- 您现在的位置：买卖IC网 > PDF目录297648 > V048T240T012 SPECIALTY ANALOG CIRCUIT, XMA60 PDF资料下载
参数资料
| 型号： | V048T240T012 |
| 元件分类： | 模拟信号调理 |
| 英文描述： | SPECIALTY ANALOG CIRCUIT, XMA60 |
| 封装： | ROHS COMPLIANT, SMD-60 |
| 文件页数： | 11/11页 |
| 文件大小： | 691K |
| 代理商： | V048T240T012 |
vicorpower.com
800-735-6200
VI Chip Voltage Transformation Module
V048F240T012
Rev. 2.2
Page 9 of 11
Figure 15 — VTM test circuit
Parallel Operation
In applications requiring higher current or redundancy, VTMs can be
operated in parallel without adding control circuitry or signal lines. To
maximize current sharing accuracy, it is imperative that the source and
load impedance on each VTM in a parallel array be equal. If VTMs are
being fed by an upstream PRM, the VC nodes of all VTMs must be
connected to the PRM VC.
To achieve matched impedances, dedicated power planes within the PC
board should be used for the output and output return paths to the
array of paralleled VTMs. This technique is preferable to using traces of
varying size and length.
The VTM power train and control architecture allow bi-directional
power transfer when the VTM is operating within its specified ranges.
Bi-directional power processing improves transient response in the
event of an output load dump. The VTM may operate in reverse,
returning output power back to the input source. It does so efficiently.
Input Impedance Recommendations
To take full advantage of the VTM’s capabilities, the impedance of the
source (input source plus the PC board impedance) must be low over a
range from DC to 5 MHz. The input of the VTM (factorized bus) should
be locally bypassed with a 8 F low Q aluminum electrolytic capacitor.
Additional input capacitance may be added to improve transient
performance or compensate for high source impedance. The VTM has
extremely wide bandwidth so the source response to transients is
usually the limiting factor in overall output response of the VTM.
Anomalies in the response of the source will appear at the output of
the VTM, multiplied by its K factor of 1/2. The DC resistance of the
source should be kept as low as possible to minimize voltage deviations
on the input to the VTM. If the VTM is going to be operating close to
the high limit of its input range, make sure input voltage deviations will
not trigger the input overvoltage turn-off threshold.
Input Fuse Recommendations
VI Chips are not internally fused in order to provide flexibility in
configuring power systems. However, input line fusing of VI Chips
must always be incorporated within the power system. A fast acting
fuse is required to meet safety agency Conditions of Acceptability. The
input line fuse should be placed in series with the +In port.
Application Notes
For VTM and VI Chip application notes on soldering, thermal
management, board layout, and system design click on the link below:
Application Note
F1
Load
+
–
Input reflected ripple
measurement point
C2
0.47 μF
ceramic
+
–
14 V
-In
PC
VC
TM
+In
-Out
+Out
VTM
+Out
-Out
K
Ro
Notes:
C3 should be placed close
to the load
R3 may be ESR of C3 or a
separate damping resistor.
C3
3.3 F
R3
10 m
C1
47 F
Al electrolytic
10A
Fuse
IQ
+
–
+
VOUT
VIN
VI
K
+
–
+
–
IOUT
ROUT
–
VI Chip VTM Level 1 DC Behavioral Model for 48 V to 24 V, 12.5 A
Figure 16 — This model characterizes the DC operation of the VI Chip VTM, including the converter transfer function and its losses. The model enables
estimates or simulations of output voltage as a function of input voltage and output load, as well as total converter power dissipation or heat generation.
43.6 m
1/2 Vin
1/2 Iout
83 mA
相关PDF资料 |
PDF描述 |
|---|---|
| V048F240M012 | SPECIALTY ANALOG CIRCUIT, XMA60 |
| V048T480M006 | SPECIALTY ANALOG CIRCUIT, XMA |
| V110C12E100B | 1-OUTPUT 100 W DC-DC REG PWR SUPPLY MODULE |
| V110C12M100B2 | 1-OUTPUT 100 W DC-DC REG PWR SUPPLY MODULE |
| V110C12T100BN | 1-OUTPUT 100 W DC-DC REG PWR SUPPLY MODULE |
相关代理商/技术参数 |
参数描述 |
|---|---|
| V048T320M006 | 制造商:VICOR 制造商全称:Vicor Corporation 功能描述:VTM Current Multiplier |
| V048T320M009 | 制造商:Vicor Corporation 功能描述:VTM CURRENT MULTIPLIER 32V 9A |
| V048T320T006 | 制造商:VICOR 制造商全称:Vicor Corporation 功能描述:VTM Current Multiplier |
| V048T320T009 | 功能描述:VTM CURRENT MULTIPLIER 32V 9.40A RoHS:是 类别:电源 - 板载 >> DC DC 转换器（分解式） 系列:V-I Chip™, VTM™ 应用说明:Factorized Power Architecture and V-I Chips 产品培训模块:VI Chip Bus Converter Modules 标准包装:1 系列:V-I Chip™, BCM™ 类型:总线转换器模块 输出数:1 电压 - 输入（最小）:330V 电压 - 输入（最大）:365V 输出电压:12.5V 电流 - 输出（最大）:24A 电源（瓦） - 制造商系列:300W 电压 - 隔离:4.242kV（4242V） 应用:商用 特点:具有远程开/关功能和 UVLO 安装类型:通孔 封装/外壳:模块 尺寸/尺寸:1.28" L x 0.87" W x 0.26" H（32.5mm x 22.0mm x 6.7mm） 包装:托盘 工作温度:-55°C ~ 125°C 效率:95.3% 电源（瓦特）- 最大:300W 重量:0.031 磅（14.06g） |
| V048T480M006 | 制造商:Vicor Corporation 功能描述:VTM CURRENT MULTIPLIER 48V 6A |
发布紧急采购，3分钟左右您将得到回复。