- 您现在的位置：买卖IC网 > PDF目录17002 > VNCLO-PSU-USA (FTDI, Future Technology Devices International Ltd)POWER SUPPLY FOR VNCLO-MB1A USA PDF资料下载
参数资料
| 型号： | VNCLO-PSU-USA |
| 厂商： | FTDI, Future Technology Devices International Ltd |
| 文件页数： | 16/25页 |
| 文件大小： | 0K |
| 描述： | POWER SUPPLY FOR VNCLO-MB1A USA |
| 应用说明： | Vinco LCD Interface Example Vinco Graphics Display Example Vinco Volt Meter Example Using the Vinco Libraries |
| 产品变化通告： | Name Change to Vinco 22/Apr/2011 |
| 特色产品： | Vinco Development Board |
| 标准包装： | 1 |
| 系列： | Vinco |
| 附件类型： | 电源 |
| 适用于相关产品： | FTDI Vinco 卡 |
| 其它名称： | 768-1092 |
Document Reference No.: FT_000327
Vinco Development Module Datasheet Version 2.01
Clearance No.: FTDI#173
5
Debugger Interface
The purpose of the debugger interface, J8, is to provide access to the VNC2 silicon/firmware debugger.
The debug interface can be accessed by connecting a VNC2_Debugger_Programmer_Module to the J8
connector. This debugger/programmer module will give access to the debugger through a USB connection
to a PC via the Integrated Development Environment (IDE). The IDE is accessed through a GUI to the
VNC2 software development tool-chain and gives the following debug capabilities through the debugger
interface:
?
?
?
Flash Erase, Write and Program.
Application debug - application code can have breakpoints, be single stepped and can be halted.
Detailed internal debug - memory and register read/write access.
The IDE may be downloaded from http://www.ftdichip.com/Firmware/V2TC/VNC2toolchain.htm
The Debugger Interface, and how to use it, is further described in the following applications note:
5.1 Signal Description - Debugger Interface
Name
Pin No.
J7-1
Name
IO0
On PCB
DBG
Type
I/O
Debugger Interface
Description
Not connected. Used to make sure that the debug
J7-2
J7-3
J7-4
-
GND
RESET#
[Key]
GND
RST#
-
PWR
Input
module is connected correctly.
Module ground supply pin
Can be used by an external device to reset the
VNC2. This pin is also used in combination with
PROG# and the UART interface to program
firmware into the VNC2.
This pin is used in combination with the RESET#
J7-5
J7-6
PROG#
5V0
PRG#
VCC
Input
PWR Input
pin and the UART interface to program firmware
into the VNC2.
5.0V module supply pin. This pin can be used to
provide the 5.0V input to the Vinco from the
debugger interface when the Vinco is not powered
from the USB connector (VBUs) or the CN1
Table 5.1 – Signal Name and Description – Debugger Interface
Note: # defines active low signals.
Copyright ? 2012 Future Technology Devices International Limited
12
相关PDF资料 |
PDF描述 |
|---|---|
| 381LX123M025A012 | CAP ALUM 12000UF 25V 20% SNAP |
| GBM31DCTH-S288 | CONN EDGECARD 62POS .156 EXTEND |
| ESM12DSEH | CONN EDGECARD 24POS .156 EYELET |
| TLV2542EVM | EVAL MOD FOR TLV2542 |
| VI-20P-EY | CONVERTER MOD DC/DC 13.8V 50W |
相关代理商/技术参数 |
参数描述 |
|---|---|
| VNCLO-SHLD1A | 制造商:FTDI 制造商全称:FTDI 功能描述:Vinculo Development Module |
| VNCLO-SHLD-1A | 功能描述:模块配件 Vinco Prototyping Shield Accessory RoHS:否 制造商:Lantronix 产品: 用于: |
| VNCLO-START1 | 功能描述:界面开发工具 VINCO PLUS DEBUGGER PROGRAMMER MODULE RoHS:否 制造商:Bourns 产品:Evaluation Boards 类型:RS-485 工具用于评估:ADM3485E 接口类型:RS-485 工作电源电压:3.3 V |
| VND05 | 制造商:STMICROELECTRONICS 制造商全称:STMicroelectronics 功能描述:ISO HIGH SIDE SMART POWER SOLID STATE RELAY |
| VND05B | 功能描述:固态继电器-PCB安装 40V 1.6A Hi-Side SSR RoHS:否 制造商:Omron Electronics 控制电压范围: 负载电压额定值:40 V 负载电流额定值:120 mA 触点形式:1 Form A (SPST-NO) 输出设备:MOSFET 封装 / 箱体:USOP-4 安装风格:SMD/SMT |
发布紧急采购，3分钟左右您将得到回复。