- 您现在的位置：买卖IC网 > PDF目录245678 > W19B320ATT7M (WINBOND ELECTRONICS CORP) 2M X 16 FLASH 3V PROM, 70 ns, PDSO48 PDF资料下载
参数资料
| 型号： | W19B320ATT7M |
| 厂商： | WINBOND ELECTRONICS CORP |
| 元件分类： | PROM |
| 英文描述： | 2M X 16 FLASH 3V PROM, 70 ns, PDSO48 |
| 封装： | 12 X 20 MM, LEAD FREE, TSOP-48 |
| 文件页数： | 24/53页 |
| 文件大小： | 479K |
| 代理商： | W19B320ATT7M |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页当前第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页第44页第45页第46页第47页第48页第49页第50页第51页第52页第53页
W19B320AT/B
- 30 -
SA = Address of the sector to be verified (in AUTOSELECT mode) or erased. Address bits A20-A12 uniquely select any sector.
BA = Address of the bank that is being switched to AUTOSELECT mode, is in bypass mode, or is being erased
Notes:
1. See Bus Operations Table for details.
2. All values are in hexadecimal.
3. Except for the read cycle and the fourth cycle of the AUTOSELECT command sequence, all bus cycles are write cycles.
4. Data bits DQ15-DQ8 are don’t care in command sequences, except for RD and PD.
5. Unless otherwise noted, address bits A20-A11 are “don’t care”.
6. No unlock or command cycles required when bank is reading array data.
7. The Reset command is required to return to the read mode (or to the erase-suspend-read mode if previously in Erase
Suspend) when a bank is in the AUTOSELECT mode, or if DQ5 goes high (while the bank is providing status
information).
8. The fourth cycle of the AUTOSELECT command sequence is a read cycle. The system must provide the bank address
to obtain the manufacturer ID, device ID, or Security Sector factory protect information. Data bits DQ15-DQ8 are don’t
care. See the AUTOSELECT Command Sequence section for more information.
9. The data is 82h for factory locked and 02h for not factory locked.
10. The data is 00h for an unprotected sector/sector block and 01h for a protected sector/sector block.
11. The Unlock Bypass command is required prior to the Unlock Bypass Program command.
12. The Unlock Bypass Reset command is required to return to the read mode when the bank is in the unlock bypass mode.
13. The system may read and program in non-erasing sectors, or enter the AUTOSELECT mode, when in the Erase
Suspend mode. The Erase Suspend command is valid only during a sector erase operation, and requires the bank
address.
14. The Erase Resume command is valid only during the Erase Suspend mode, and requires the bank address.
15. Command is valid when device is ready to read array data or when device is in AUTOSELECT mode.
7.5.5
Write Operation Status
STATUS
DQ7
(NOTE 2)
DQ6
DQ5
(NOTE1)
DQ3
DQ2
(NOTE 2)
RY/#BY
Embedded Program
Algorithm
#DQ7
Toggle
0
N/A
No toggle
0
Standard
Mode
Embedded Erase Algorithm
0
Toggle
0
1
Toggle
0
Erase
Suspended
Sector
1
No toggle
0
N/A
Toggle
1
Erase-
Suspend
Read
Non-Erase
Suspended
Sector
Data
1
Erase
Suspend
Mode
Erase-Suspend-Program
#DQ7
Toggle
0
N/A
0
Notes:
1. DQ5 switches to ‘1’ when an Embedded Program or Embedded Erase operation has exceeded the maximum timing
limits. Refer to DQ5 description section for more information.
2. DQ7 and DQ2 require a valid address when reading status information. Refer to the appropriate subsection for further
details.
3. When reading write operation status bits, the system must always provide the bank address where the Embedded
Algorithm is in progress. The device outputs array data if the system addresses a non-busy bank.
相关PDF资料 |
PDF描述 |
|---|---|
| W3DG6416V10D1 | 16M X 64 SYNCHRONOUS DRAM MODULE, ZMA144 |
| W3EG7266S265D3 | 64M X 72 DDR DRAM MODULE, 0.75 ns, DMA184 |
| WED3EG72M32S403JD3GG | 32M X 72 DDR DRAM MODULE, 0.7 ns, DMA184 |
| WED9LAPC2C16P8BI | 4M X 32 SYNCHRONOUS DRAM, PBGA153 |
| W19B320ABB8L | 2M X 16 FLASH 3V PROM, 70 ns, PBGA48 |
相关代理商/技术参数 |
参数描述 |
|---|---|
| W19B320B | 制造商:WINBOND 制造商全称:Winbond 功能描述:32Mbit, 2.7~3.6-volt single bank CMOS flash memory |
| W19B320BB | 制造商:WINBOND 制造商全称:Winbond 功能描述:32Mbit, 2.7~3.6-volt single bank CMOS flash memory |
| W19B320BB-H | 制造商:WINBOND 制造商全称:Winbond 功能描述:2.7~3.6-volt write (program and erase) operations |
| W19B320BB-M | 制造商:WINBOND 制造商全称:Winbond 功能描述:2.7~3.6-volt write (program and erase) operations |
| W19B320BT | 制造商:WINBOND 制造商全称:Winbond 功能描述:32Mbit, 2.7~3.6-volt single bank CMOS flash memory |
发布紧急采购，3分钟左右您将得到回复。