- 您现在的位置：买卖IC网 > PDF目录300103 > W25Q40BVSSIG (WINBOND ELECTRONICS CORP) 4M X 1 FLASH 2.7V PROM, PDSO8 PDF资料下载
参数资料
| 型号： | W25Q40BVSSIG |
| 厂商： | WINBOND ELECTRONICS CORP |
| 元件分类： | PROM |
| 英文描述： | 4M X 1 FLASH 2.7V PROM, PDSO8 |
| 封装： | 0.208 INCH, GREEN, PLASTIC, SOIC-8 |
| 文件页数： | 3/73页 |
| 文件大小： | 2222K |
| 代理商： | W25Q40BVSSIG |
第1页第2页当前第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页第44页第45页第46页第47页第48页第49页第50页第51页第52页第53页第54页第55页第56页第57页第58页第59页第60页第61页第62页第63页第64页第65页第66页第67页第68页第69页第70页第71页第72页第73页
W25Q40BV
Publication Release Date: July 08, 2010
- 11 -
Preliminary - Revision B
8.
CONTROL AND STATUS REGISTERS
The Read Status Register-1 and Status Register-2 instructions can be used to provide status on the
availability of the Flash memory array, if the device is write enabled or disabled, the state of write
protection, Quad SPI setting, Security Register lock status and Erase/Program Suspend status. The Write
Status Register instruction can be used to configure the device write protection features, Quad SPI setting
and Security Register OTP lock. Write access to the Status Register is controlled by the state of the non-
volatile Status Register Protect bits (SRP0, SRP1), the Write Enable instruction, and during
Standard/Dual SPI operations, the /WP pin.
8.1 STATUS REGISTER
8.1.1
BUSY
BUSY is a read only bit in the status register (S0) that is set to a 1 state when the device is executing a
Page Program, Quad Page Program, Sector Erase, Block Erase, Chip Erase, Write Status Register or
Erase/Program Security Register instruction. During this time the device will ignore further instructions
except for the Read Status Register and Erase/Program Suspend instruction (see tW, tPP, tSE, tBE, and
tCE in AC Characteristics). When the program, erase or write status/security register instruction has
completed, the BUSY bit will be cleared to a 0 state indicating the device is ready for further instructions.
8.1.2
Write Enable Latch (WEL)
Write Enable Latch (WEL) is a read only bit in the status register (S1) that is set to 1 after executing a
Write Enable Instruction. The WEL status bit is cleared to 0 when the device is write disabled. A write
disable state occurs upon power-up or after any of the following instructions: Write Disable, Page
Program, Quad Page Program, Sector Erase, Block Erase, Chip Erase, Write Status Register, Erase
Security Register and Program Security Register.
8.1.3
Block Protect Bits (BP2, BP1, BP0)
The Block Protect Bits (BP2, BP1, BP0) are non-volatile read/write bits in the status register (S4, S3, and
S2) that provide Write Protection control and status. Block Protect bits can be set using the Write Status
Register Instruction (see tW in AC characteristics). All, none or a portion of the memory array can be
protected from Program and Erase instructions (see Status Register Memory Protection table). The
factory default setting for the Block Protection Bits is 0, none of the array protected.
8.1.4
Top/Bottom Block Protect (TB)
The non-volatile Top/Bottom bit (TB) controls if the Block Protect Bits (BP2, BP1, BP0) protect from the
Top (TB=0) or the Bottom (TB=1) of the array as shown in the Status Register Memory Protection table.
The factory default setting is TB=0. The TB bit can be set with the Write Status Register Instruction
depending on the state of the SRP0, SRP1 and WEL bits.
8.1.5
Sector/Block Protect (SEC)
The non-volatile Sector/Block Protect bit (SEC) controls if the Block Protect Bits (BP2, BP1, BP0) protect
either 4KB Sectors (SEC=1) or 64KB Blocks (SEC=0) in the Top (TB=0) or the Bottom (TB=1) of the
array as shown in the Status Register Memory Protection table. The default setting is SEC=0.
相关PDF资料 |
PDF描述 |
|---|---|
| W27L02-90 | 256K X 8 EEPROM 12V, 90 ns, PDIP32 |
| W28J800BT90L | 512K X 16 FLASH 2.7V PROM, 90 ns, PDSO48 |
| W28J800BT90C | 512K X 16 FLASH 2.7V PROM, 90 ns, PDSO48 |
| W29EE011-20 | 128K X 8 EEPROM 5V, 200 ns, PDIP32 |
| W39L040P-70Z | 512K X 8 FLASH 3.3V PROM, 70 ns, PQCC32 |
相关代理商/技术参数 |
参数描述 |
|---|---|
| W25Q40BVSSIP | 制造商:WINBOND 制造商全称:Winbond 功能描述:4M-BIT SERIAL FLASH MEMORY WITH DUAL AND QUAD SPI |
| W25Q40BVZPIG | 制造商:WINBOND 制造商全称:Winbond 功能描述:4M-BIT SERIAL FLASH MEMORY WITH DUAL AND QUAD SPI |
| W25Q40BVZPIP | 制造商:WINBOND 制造商全称:Winbond 功能描述:4M-BIT SERIAL FLASH MEMORY WITH DUAL AND QUAD SPI |
| W25Q40BW | 制造商:WINBOND 制造商全称:Winbond 功能描述:1.8V 4M-BIT SERIAL FLASH MEMORY WITH DUAL AND QUAD SPI |
| W25Q40BWSNIG | 功能描述:IC FLASH SPI 4MBIT 8SOIC RoHS:是 类别:集成电路 (IC) >> 存储器 系列:SpiFlash® 标准包装:2,500 系列:- 格式 - 存储器:EEPROMs - 串行 存储器类型:EEPROM 存储容量:1K (128 x 8) 速度:100kHz 接口:UNI/O?（单线） 电源电压:1.8 V ~ 5.5 V 工作温度:-40°C ~ 85°C 封装/外壳:8-TSSOP，8-MSOP（0.118"，3.00mm 宽） 供应商设备封装:8-MSOP 包装:带卷 (TR) |
发布紧急采购，3分钟左右您将得到回复。