- 您现在的位置：买卖IC网 > PDF目录68746 > W33D2031 (WINBOND ELECTRONICS CORP) LIQUID CRYSTAL DISPLAY DRIVER, PQFP64 PDF资料下载
参数资料
| 型号： | W33D2031 |
| 厂商： | WINBOND ELECTRONICS CORP |
| 元件分类： | 显示驱动器 |
| 英文描述： | LIQUID CRYSTAL DISPLAY DRIVER, PQFP64 |
| 封装： | PLASTIC, QFP-64 |
| 文件页数： | 2/28页 |
| 文件大小： | 305K |
| 代理商： | W33D2031 |
第1页当前第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页
W33D0001 SERIES
- 10 -
1.5 Timer mode:
The timer mode is controlled by the ATS pin with first priority. When the ATS pin is high, the timer
function is inhibited meaning the timer data cannot display on the LCD panel. This timer function
exists only when ATS pin is low, the MS pin is high, and Timer bit is equal to zero. Refer to Figure 9.
In timer mode, the elapsed conversation time since the beginning of the call is displayed on the LCD
panel. When the MS pin goes from low to high and the no data is transmitted, the LCD panel will
show a flashing first digit (3 bars).
When the MS pin is high, and no data transmission occur for more than 6 seconds, the timer will
automatically start to count until the MS pin returns to a low state (in this case, the timer data will be
kept for 5 sec. Befor being transferned to clock data). The maximum counting time is 11-59-59, and
cycles to 00-00-00 to start again.
The other method of starting and stopping the timer is by triggering the TIM pin. A high trigger input
on the TIM pin will reverse the current condition of the timer; thus if the timer is counting, a high
trigger on TIM will stop the counter, and vice versa. When the timer is in the initial state and the first
trigger on the TIM pin occurs before the normal mode transmission data, the timer will display the
previous counting number.
Detailed flow charts depicting the above three operating modes are shown in Figure 5 and Figure 6.
2. Reset Function
There are two methods for initializing the chip: one is power-on reset, the other is pulling the RST
pin low (low active).
2.1. Power-on reset
At power on reset , the power-on reset circuit will generate a pulse to reset the chip. All LCD
segments will flash momentarily for about 2 seconds and the built-in clock will start from 1
1 0000
and the normal mode data of 128 dots will be reset to "0".
2.2. RST Pin function
Pulling RST low will reset all of the chip's functions except for the clock. All LCD segments will flash
momentarily for about 2 seconds and the 128 dots will be reset to "0".
3. LCD Format
The LCD panel is 1/3 bias, 1/4 duty. Refer to Figure 10 and Figure 11. The LCD format is shown in
Figure 12.
相关PDF资料 |
PDF描述 |
|---|---|
| W33D2041 | LIQUID CRYSTAL DISPLAY DRIVER, PQFP64 |
| W33D2111 | LIQUID CRYSTAL DISPLAY DRIVER, PQFP64 |
| W33D2121 | LIQUID CRYSTAL DISPLAY DRIVER, PQFP64 |
| W33D2131 | LIQUID CRYSTAL DISPLAY DRIVER, PQFP64 |
| W33D2141 | LIQUID CRYSTAL DISPLAY DRIVER, PQFP64 |
相关代理商/技术参数 |
参数描述 |
|---|---|
| W33-D3B1Q-20 | 制造商:TE Connectivity 功能描述: |
| W33FX-22 | 制造商:Magnecraft 功能描述: |
| W33HSX-178 | 制造商:Struthers-Dunn 功能描述: |
| W33HSX-179 | 制造商:Struthers-Dunn 功能描述: |
| W33HSX-182 | 制造商:Struthers-Dunn 功能描述: |
发布紧急采购，3分钟左右您将得到回复。