- 您现在的位置：买卖IC网 > PDF目录10935 > W681511SG (Nuvoton Technology Corporation of America)IC VOICEBAND CODEC 5V 1CH 20SOP PDF资料下载
参数资料
| 型号： | W681511SG |
| 厂商： | Nuvoton Technology Corporation of America |
| 文件页数： | 3/32页 |
| 文件大小： | 0K |
| 描述： | IC VOICEBAND CODEC 5V 1CH 20SOP |
| 其它有关文件： | CODEC Block Diagram |
| 标准包装： | 38 |
| 类型： | PCM |
| 数据接口： | PCM 音频接口 |
| 分辨率（位）： | 8 b |
| ADC / DAC 数量： | 1 / 1 |
| 三角积分调变： | 无 |
| 电压 - 电源，模拟： | 4.5 V ~ 5.5 V |
| 电压 - 电源，数字： | 4.5 V ~ 5.5 V |
| 工作温度： | -40°C ~ 85°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 20-SOIC（0.295"，7.50mm 宽） |
| 供应商设备封装： | 20-SOP |
| 包装： | 管件 |
| 配用： | W681513DK-ND - KIT DEVELOPMENT FOR W681513 W681512DK-ND - KIT DEVELOPMENT FOR W681512 W681511DK-ND - KIT DEVELOPMENT FOR W681511 W681512ES-ND - EVALUATION SYSTEM FOR W681512 |
第1页第2页当前第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页
W681511
Publication Release Date: January 2009
- 11 -
Revision A11
7.4.2. Short Frame Sync
The W681511 operates in the Short Frame Sync Mode when the Frame Sync signal at pin FST is high
for one and only one falling edge of the bit-clock at the BCLKT pin. On the following rising edge of the
bit-clock, the W681511 starts clocking out the data on the PCMT pin, which will also change from high
to low impedance state. The data transmit pin PCMT will go back to the high impedance state halfway
the LSB. The Short Frame Sync operation of the W681511 is based on an 8-bit data word. When
receiving data on the PCMR pin, the data is clocked in on the first falling edge after the falling edge
that coincides with the Frame Sync signal. The internal decision logic will determine whether the next
frame sync is a long or a short frame sync, based on the previous frame sync pulse. To avoid bus
collisions, the PCMT pin will be high impedance for two frame sync cycles after every power down
state. More detailed timing information can be found in the interface timing section.
7.4.3. General Circuit Interface (GCI)
The GCI interface mode is selected when the BCLKR pin is connected to VSS for two or more frame
sync cycles. It can be used as a 2B+D timing interface in an ISDN application. The GCI interface
consists of 4 pins : FSC (FST), DCL (BCLKT), Dout (PCMT) & Din (PCMR). The FSR pin selects
channel B1 or B2 for transmit and receive. Data transitions occur on the positive edges of the data
clock DCL. The Frame Sync positive edge is aligned with the positive edge of the data clock DCLK.
The data rate is running half the speed of the bit-clock. The channels B1 and B2 are transmitted
consecutively. Therefore, channel B1 is transmitted on the first 16 clock cycles of DCL and B2 is
transmitted on the second 16 clock cycles of DCL. For more timing information, see the timing section.
7.4.4. Interchip Digital Link (IDL)
The IDL interface mode is selected when the BCLKR pin is connected to VDD for two or more frame
sync cycles. It can be used as a 2B+D timing interface in an ISDN application. The IDL interface
consists of 4 pins : IDL SYNC (FST), IDL CLK (BCLKT), IDL TX (PCMT) & IDL RX (PCMR). The FSR
pin selects channel B1 or B2 for transmit and receive. The data for channel B1 is transmitted on the
first positive edge of the IDL CLK after the IDL SYNC pulse. The IDL SYNC pulse is one IDL CLK
cycle long. The data for channel B2 is transmitted on the eleventh positive edge of the IDL CLK after
the IDL SYNC pulse. The data for channel B1 is received on the first negative edge of the IDL CLK
after the IDL SYNC pulse. The data for channel B2 is received on the eleventh negative edge of the
IDL CLK after the IDL SYNC pulse. The transmit signal pin IDL TX becomes high impedance when
not used for data transmission and also in the time slot of the unused channel. For more timing
information, see the timing section.
7.4.5. System Timing
The system can work at 256 kHz, 512 kHz, 1536 kHz, 1544 kHz, 2048 kHz, 2560 kHz & 4096 kHz
master clock rates. The system clock is supplied through the master clock input MCLK and can be
derived from the bit-clock if desired. An internal pre-scaler is used to generate a fixed 256 kHz and 8
kHz sample clock for the internal CODEC. The pre-scaler measures the master clock frequency
versus the Frame Sync frequency and sets the division ratio accordingly. If the Frame Sync is low for
the entire frame sync period while the MCLK and BCLK pin clock signals are still present, the
W681511 will enter the low power standby mode. Another way to power down is to set the PUI pin to
low. When the system needs to be powered up again, the PUI pin needs to be set to high and the
Frame Sync pulse needs to be present. It will take two Frame Sync cycles before the pin PCMT will
become low impedance.
相关PDF资料 |
PDF描述 |
|---|---|
| VI-2NK-CU | CONVERTER MOD DC/DC 40V 200W |
| VI-2N4-CU | CONVERTER MOD DC/DC 48V 200W |
| VI-2N2-CU | CONVERTER MOD DC/DC 15V 200W |
| VI-2N1-CU | CONVERTER MOD DC/DC 12V 200W |
| VE-2NX-CU | CONVERTER MOD DC/DC 5.2V 200W |
相关代理商/技术参数 |
参数描述 |
|---|---|
| W681511SG TR | 功能描述:IC VOICEBAND CODEC 5V 1CH 20SOP RoHS:是 类别:集成电路 (IC) >> 接口 - 编解码器 系列:- 标准包装:2,500 系列:- 类型:立体声音频 数据接口:串行 分辨率（位）:18 b ADC / DAC 数量:2 / 2 三角积分调变:是 S/N 比，标准 ADC / DAC (db):81.5 / 88 动态范围，标准 ADC / DAC (db):82 / 87.5 电压 - 电源，模拟:2.6 V ~ 3.3 V 电压 - 电源，数字:1.7 V ~ 3.3 V 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:48-WFQFN 裸露焊盘 供应商设备封装:48-TQFN-EP（7x7） 包装:带卷 (TR) |
| W681512 | 制造商:WINBOND 制造商全称:Winbond 功能描述:SINGLE-CHANNEL VOICEBAND CODEC |
| W681512DK | 功能描述:KIT DEVELOPMENT FOR W681512 RoHS:否 类别:编程器，开发系统 >> 评估演示板和套件 系列:- 标准包装:1 系列:- 主要目的:电信，线路接口单元（LIU） 嵌入式:- 已用 IC / 零件:IDT82V2081 主要属性:T1/J1/E1 LIU 次要属性:- 已供物品:板，电源，线缆，CD 其它名称:82EBV2081 |
| W681512ES | 功能描述:EVALUATION SYSTEM FOR W681512 RoHS:否 类别:编程器，开发系统 >> 过时/停产零件编号 系列:- 标准包装:1 系列:- 类型:MCU 适用于相关产品:Freescale MC68HC908LJ/LK（80-QFP ZIF 插口） 所含物品:面板、缆线、软件、数据表和用户手册 其它名称:520-1035 |
| W681512R | 功能描述:IC VOICEBAND CODEC 5V 1CH 20SSOP RoHS:否 类别:集成电路 (IC) >> 接口 - 编解码器 系列:- 标准包装:2,500 系列:- 类型:立体声音频 数据接口:串行 分辨率（位）:18 b ADC / DAC 数量:2 / 2 三角积分调变:是 S/N 比，标准 ADC / DAC (db):81.5 / 88 动态范围，标准 ADC / DAC (db):82 / 87.5 电压 - 电源，模拟:2.6 V ~ 3.3 V 电压 - 电源，数字:1.7 V ~ 3.3 V 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:48-WFQFN 裸露焊盘 供应商设备封装:48-TQFN-EP（7x7） 包装:带卷 (TR) |
发布紧急采购，3分钟左右您将得到回复。