- 您现在的位置：买卖IC网 > PDF目录68583 > WJLXT972ALC.A4-857345 (CORTINA SYSTEMS INC) DATACOM, ETHERNET TRANSCEIVER, PQFP64 PDF资料下载
参数资料
| 型号： | WJLXT972ALC.A4-857345 |
| 厂商： | CORTINA SYSTEMS INC |
| 元件分类： | 网络接口 |
| 英文描述： | DATACOM, ETHERNET TRANSCEIVER, PQFP64 |
| 封装： | 10 X 10 MM, 1.40 MM HEIGHT, ROHS COMPLIANT, LQFP-64 |
| 文件页数： | 19/80页 |
| 文件大小： | 931K |
| 代理商： | WJLXT972ALC.A4-857345 |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页当前第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页第44页第45页第46页第47页第48页第49页第50页第51页第52页第53页第54页第55页第56页第57页第58页第59页第60页第61页第62页第63页第64页第65页第66页第67页第68页第69页第70页第71页第72页第73页第74页第75页第76页第77页第78页第79页第80页
Page 26
Cortina Systems LXT972A Single-Port 10/100 Mbps PHY Transceiver
LXT972A PHY
Datasheet
249186, Revision 5.2
13 September 2007
5.4 Initialization
The digital and analog circuits require 3.3 V supplies (VCCA and VCCD). These inputs
may be supplied from a single source. Each supply input must be de-coupled to ground.
An additional supply may be used for the MII (VCCIO). The supply may be either 2.5 V or
3.3 V. Also, the inputs on the MII interface are tolerant to 5 V signals from the controller on
the other side of the MII interface. For MII I/O characteristics, see Table 23, Digital I/O
Notes:
1. Bring up power supplies as close to the same time as possible.
2. As a matter of good practice, keep power supplies as clean as possible.
5.3.2
Clock Requirements
5.3.2.1
External Crystal/Oscillator
The LXT972A PHY requires a reference clock input that is used to generate transmit
signals and recover receive signals. It may be provided by either of two methods: by
connecting a crystal across the oscillator pins (XI and XO) with load capacitors, or by
connecting an external clock source to pin XI.
The connection of a clock source to the XI pin requires the XO pin to be left open. To
minimize transmit jitter, Cortina recommends a crystal-based clock instead of a derived
clock (that is, a PLL-based clock).
A crystal is typically used in NIC applications. An external 25 MHz clock source, rather
than a crystal, is frequently used in switch applications. For clock timing requirements, see
5.3.2.2
MDIO Clock
The MII management channel (MDIO) also requires an external clock. The managed data
clock (MDC) speed is a maximum of 8 MHz.
5.4
Initialization
This section includes the following topics:
When the LXT972A PHY is first powered on, reset, or encounters a link failure state, it
checks the MDIO register configuration bits to determine the line speed and operating
conditions to use for the network link.
Table 13 shows the LXT972A PHY initialization sequence. The configuration bits may be
set by the Hardware Control or MDIO interface.
5.4.1
MDIO Control Mode and Hardware Control Mode
In the MDIO Control mode, the LXT972A PHY reads the Hardware Control Interface pins
to set the initial (default) values of the MDIO registers. Once the initial values are set, bit
control reverts to the MDIO interface.
The following modes are available using either Hardware Control or MDIO control:
相关PDF资料 |
PDF描述 |
|---|---|
| WJLXT971ALC.A4SE000 | DATACOM, ETHERNET TRANSCEIVER, PQFP64 |
| WJLXT971ALC.A4SE001 | DATACOM, ETHERNET TRANSCEIVER, PQFP64 |
| WJLXT971ALE.A4SE000 | DATACOM, ETHERNET TRANSCEIVER, PQFP64 |
| WJLXT971ALE.A4SE001 | DATACOM, ETHERNET TRANSCEIVER, PQFP64 |
| WJLXT971ALC.A4SE000 | DATACOM, ETHERNET TRANSCEIVER, PQFP64 |
相关代理商/技术参数 |
参数描述 |
|---|---|
| WJLXT972MLC.A4 | 功能描述:IC TRANS 3.3V ETHERNET 48-LQFP RoHS:是 类别:集成电路 (IC) >> 接口 - 驱动器，接收器，收发器 系列:- 产品培训模块:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 标准包装:25 系列:- 类型:收发器 驱动器/接收器数:2/2 规程:RS232 电源电压:4.5 V ~ 5.5 V 安装类型:通孔 封装/外壳:16-DIP（0.300"，7.62mm） 供应商设备封装:16-PDIP 包装:管件 |
| WJLXT972MLC.A4 S L7U9 | 制造商:Intel 功能描述:PHY 1-CH 10Mbps/100Mbps 64-Pin LQFP |
| WJLXT972MLC.A4-864115 | 功能描述:TXRX ETH 10/100 SGL PORT 48-LQFP RoHS:是 类别:集成电路 (IC) >> 接口 - 驱动器，接收器，收发器 系列:- 产品培训模块:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 标准包装:50 系列:- 类型:收发器 驱动器/接收器数:1/1 规程:RS422，RS485 电源电压:4.75 V ~ 5.25 V 安装类型:通孔 封装/外壳:8-DIP（0.300"，7.62mm） 供应商设备封装:8-PDIP 包装:管件 产品目录页面:1402 (CN2011-ZH PDF) |
| WJLXT972MLCA4 | 制造商:Cortina Systems Inc 功能描述: |
| WJM1000 | 功能描述:射频模块 902-928 MHz US ISM EPC Class 1 Gen 2 RoHS:否 制造商:Linx Technologies 产品:Transceiver Modules 频带:902 MHz to 928 MHz 输出功率:- 15.5 dBm to + 12.5 dBm 接口类型:UART 工作电源电压:- 0.3 VDC to + 5.5 VDC 传输供电电流:38.1 mA 接收供电电流:22.7 mA 天线连接器类型:U.FL 最大工作温度:+ 85 C 尺寸:1.15 mm x 0.63 mm x 0.131 mm |
发布紧急采购，3分钟左右您将得到回复。