参数资料
| 型号： | X4005M8I |
| 厂商： | Intersil |
| 文件页数： | 8/16页 |
| 文件大小： | 0K |
| 描述： | IC SUPERVISOR CPU I2C 8-MSOP |
| 标准包装： | 80 |
| 类型： | 简单复位/加电复位 |
| 监视电压数目： | 1 |
| 输出： | 开路漏极或开路集电极 |
| 复位： | 高有效 |
| 复位超时： | 最小为 100 ms |
| 电压 - 阀值： | 4.38V |
| 工作温度： | -40°C ~ 85°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 8-TSSOP，8-MSOP（0.118"，3.00mm 宽） |
| 供应商设备封装： | 8-MSOP |
| 包装： | 管件 |
X4003, X4005
SCL
SDA
START
STOP
FIGURE 7. VALID START AND STOP CONDITIONS
SCL FROM
MASTER
DATA OUTPUT
FROM
TRANSMITTER
DATA OUTPUT
FROM RECEIVER
START
1
8
9
ACKNOWLEDGE
FIGURE 8. ACKNOWLEDGE RESPONSE FROM RECEIVER
SIGNALS
FROM THE
MASTER
SDA BUS
SIGNALS
FROM THE
SLAVE
ADDRESS
1 0 1 1 0 0 1 0
A
C
K
BYTE
ADDRESS
1 1 1 1 1 1 1 1
A
C
K
DATA
A
C
K
SLAVE
FIGURE 9. WRITE CONTROL REGISTER SEQUENCE
Serial Start Condition
All commands are preceded by the start condition, which is a
HIGH to LOW transition of SDA when SCL is HIGH. The
device continuously monitors the SDA and SCL lines for the
start condition and will not respond to any command until
Serial Stop Condition
All communications must be terminated by a stop condition,
which is a LOW to HIGH transition of SDA when SCL is
HIGH. The stop condition is also used to place the device
into the Standby power mode after a read sequence. A stop
condition can only be issued after the transmitting device
Serial Acknowledge
Acknowledge is a software convention used to indicate
successful data transfer. The transmitting device, either
master or slave, will release the bus after transmitting eight
bits. During the ninth clock cycle, the receiver will pull the
8
SDA line LOW to acknowledge that it received the eight bits
The device will respond with an acknowledge after
recognition of a start condition and the correct contents of
the slave address byte. Acknowledge bits are also provided
by the X4003/4005 after correct reception of the control
register address byte, after receiving the byte written to the
control register and after the second slave address in a read
question (see Figures 9 and 10).
Serial Write Operations
Slave Address Byte
Following a start condition, the master must output a slave
address byte. This byte consists of several parts:
? a device type identifier that is always ‘1011’.
? two bits of ‘0’.
? one bit of the slave command byte is a R/W bit. The R/W
bit of the slave address byte defines the operation to be
FN8113.2
June 30, 2008
相关PDF资料 |
PDF描述 |
|---|---|
| X4005M8-4.5A | IC SUPERVISOR CPU I2C 8-MSOP |
| 450MXH330MEFCSN35X30 | CAP ALUM 330UF 450V 20% SNAP-IN |
| UA78L05ACDG4 | IC REG LDO 5V .1A 8SOIC |
| X4005M8-2.7A | IC SUPERVISOR CPU I2C 8-MSOP |
| AS1364-BTDT-AD | IC REG LDO ADJ 1A 8-TDFN |
相关代理商/技术参数 |
参数描述 |
|---|---|
| X4005M8I-2.7 | 功能描述:IC SUPERVISOR CPU I2C 8-MSOP RoHS:否 类别:集成电路 (IC) >> PMIC - 监控器 系列:- 标准包装:100 系列:- 类型:简单复位/加电复位 监视电压数目:1 输出:- 复位:低有效 复位超时:最小为 100 ms 电压 - 阀值:4.38V 工作温度:0°C ~ 70°C 安装类型:表面贴装 封装/外壳:8-TSSOP（0.173"，4.40mm 宽） 供应商设备封装:8-TSSOP 包装:管件 |
| X4005M8I-2.7A | 功能描述:IC SUPERVISOR CPU I2C 8-MSOP RoHS:否 类别:集成电路 (IC) >> PMIC - 监控器 系列:- 标准包装:100 系列:- 类型:简单复位/加电复位 监视电压数目:1 输出:- 复位:低有效 复位超时:最小为 100 ms 电压 - 阀值:4.38V 工作温度:0°C ~ 70°C 安装类型:表面贴装 封装/外壳:8-TSSOP（0.173"，4.40mm 宽） 供应商设备封装:8-TSSOP 包装:管件 |
| X4005M8I-4.5A | 功能描述:IC SUPERVISOR CPU I2C 8-MSOP RoHS:否 类别:集成电路 (IC) >> PMIC - 监控器 系列:- 标准包装:100 系列:- 类型:简单复位/加电复位 监视电压数目:1 输出:- 复位:低有效 复位超时:最小为 100 ms 电压 - 阀值:4.38V 工作温度:0°C ~ 70°C 安装类型:表面贴装 封装/外壳:8-TSSOP（0.173"，4.40mm 宽） 供应商设备封装:8-TSSOP 包装:管件 |
| X4005M8IZ | 功能描述:IC SUPERVISOR CPU I2C 8-MSOP RoHS:是 类别:集成电路 (IC) >> PMIC - 监控器 系列:- 产品培训模块:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 标准包装:2,500 系列:- 类型:简单复位/加电复位 监视电压数目:1 输出:开路漏极或开路集电极 复位:低有效 复位超时:最小为 600 ms 电压 - 阀值:3.8V 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:SC-74A，SOT-753 供应商设备封装:SOT-23-5 包装:带卷 (TR) |
| X4005M8IZ-2.7 | 功能描述:IC SUPERVISOR CPU I2C 8-MSOP RoHS:是 类别:集成电路 (IC) >> PMIC - 监控器 系列:- 产品培训模块:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 标准包装:2,500 系列:- 类型:简单复位/加电复位 监视电压数目:1 输出:开路漏极或开路集电极 复位:低有效 复位超时:最小为 600 ms 电压 - 阀值:3.8V 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:SC-74A，SOT-753 供应商设备封装:SOT-23-5 包装:带卷 (TR) |
发布紧急采购，3分钟左右您将得到回复。