- 您现在的位置：买卖IC网 > PDF目录15088 > X4045S8Z-2.7A (Intersil)IC CPU SUPERV 4K EEPROM 8-SOIC PDF资料下载
参数资料
| 型号： | X4045S8Z-2.7A |
| 厂商： | Intersil |
| 文件页数： | 12/24页 |
| 文件大小： | 0K |
| 描述： | IC CPU SUPERV 4K EEPROM 8-SOIC |
| 产品培训模块： | Solutions for Industrial Control Applications |
| 标准包装： | 100 |
| 类型： | 简单复位/加电复位 |
| 监视电压数目： | 1 |
| 输出： | 开路漏极或开路集电极 |
| 复位： | 高有效 |
| 复位超时： | 最小为 100 ms |
| 电压 - 阀值： | 2.92V |
| 工作温度： | 0°C ~ 70°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 8-SOIC（0.154"，3.90mm 宽） |
| 供应商设备封装： | 8-SOIC |
| 包装： | 管件 |
X4043, X4045
Figure 10. Byte Write Sequence
Signals from
the Master
S
t
a
r
t
Slave
Address
Byte
Address
Data
S
t
o
p
SDA Bus
0
Signals from
the Slave
A
C
K
A
C
K
A
C
K
Page Write
The device is capable of a page write operation. It is
initiated in the same manner as the byte write opera-
tion; but instead of terminating the write cycle after the
first data byte is transferred, the master can transmit
an unlimited number of 8-bit bytes. After the receipt of
each byte, the device will respond with an acknowl-
edge, and the address is internally incremented by
one. The page address remains constant. When the
counter reaches the end of the page, it “rolls over” and
goes back to ‘0’ on the same page. This means that
the master can write 16 bytes to the page starting at
any location on that page. If the master begins writing
at location 10, and loads 12 bytes, then the first 5
bytes are written to locations 10 through 15, and the
last 7 bytes are written to locations 0 through 6. After-
wards, the address counter would point to location 7 of
the page that was just written. If the master supplies
more than 16 bytes of data, then new data over-writes
the previous data, one byte at a time.
Figure 11. Page Write Operation
(1 ≤ n ≤ 16)
S
Signals from
the Master
t
a
r
Slave
Address
Byte
Address
Data
(1)
Data
(n)
S
t
o
SDA Bus
t
0
p
Signals from
the Slave
A
C
K
A
C
K
A
C
K
A
C
K
Figure 12. Writing 12-bytes to a 16-byte page starting at location 10
7 Bytes
5 Bytes
Address
=6
Address Pointer
Ends Here
Addr = 7
Address
10
Address
n-1
The master terminates the data byte loading by issu-
ing a stop condition, which causes the device to begin
the nonvolatile write cycle. As with the byte write opera-
tion, all inputs are disabled until completion of the inter-
nal write cycle. See Figure 11 for the address,
acknowledge, and data transfer sequence.
12
Stops and Write Modes
Stop conditions (that terminate write operations) must
be sent by the master after sending at least 1 full data
byte, plus the subsequent ACK signal. If a stop is
issued in the middle of a data byte, or before 1 full
data byte plus its associated ACK is sent, then the
device will reset itself without performing the write. The
contents of the array will not be effected.
FN8118.2
March 16, 2006
相关PDF资料 |
PDF描述 |
|---|---|
| RBM36DSEI | CONN EDGECARD 72POS .156 EYELET |
| H2AXG-10108-V4-ND | JUMPER-H1503TR/A2015V/X 8" |
| H2AXG-10108-S4-ND | JUMPER-H1503TR/A2015S/X 8" |
| H2AXG-10108-R4-ND | JUMPER-H1503TR/A2015R/X 8" |
| H2AXG-10108-N4-ND | JUMPER-H1503TR/A2015N/X 8" |
相关代理商/技术参数 |
参数描述 |
|---|---|
| X4045S8Z-4.5A | 功能描述:IC CPU SUPERV 4K EEPROM 8-SOIC RoHS:是 类别:集成电路 (IC) >> PMIC - 监控器 系列:- 产品培训模块:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 标准包装:2,500 系列:- 类型:简单复位/加电复位 监视电压数目:1 输出:开路漏极或开路集电极 复位:低有效 复位超时:最小为 600 ms 电压 - 阀值:3.8V 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:SC-74A，SOT-753 供应商设备封装:SOT-23-5 包装:带卷 (TR) |
| X4045S8ZT1 | 功能描述:IC CPU SUPERV 4K EEPROM 8-SOIC RoHS:是 类别:集成电路 (IC) >> PMIC - 监控器 系列:- 产品培训模块:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 标准包装:2,500 系列:- 类型:简单复位/加电复位 监视电压数目:1 输出:开路漏极或开路集电极 复位:低有效 复位超时:最小为 600 ms 电压 - 阀值:3.8V 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:SC-74A，SOT-753 供应商设备封装:SOT-23-5 包装:带卷 (TR) |
| X4045SF1 | 制造商:ABB Control 功能描述:CCT,45VA,460V,SINGLE |
| X4045-SKT | 制造商:P&S 功能描述:5128Bit CPU Supervisor with 4Kb SPI EEPROM |
| X4050PSF1 | 制造商:ABB Low Voltage Products and Systems 功能描述:CCT,50VA,460V,SINGLE |
发布紧急采购，3分钟左右您将得到回复。