- 您现在的位置：买卖IC网 > PDF目录13096 > X4165S8I (Intersil)IC CPU SUPRV 16K EE RST HI 8SOIC PDF资料下载
参数资料
| 型号： | X4165S8I |
| 厂商： | Intersil |
| 文件页数： | 12/22页 |
| 文件大小： | 0K |
| 描述： | IC CPU SUPRV 16K EE RST HI 8SOIC |
| 标准包装： | 200 |
| 类型： | 简单复位/加电复位 |
| 监视电压数目： | 1 |
| 输出： | 开路漏极或开路集电极 |
| 复位： | 高有效 |
| 复位超时： | 最小为 100 ms |
| 电压 - 阀值： | 4.38V |
| 工作温度： | -40°C ~ 85°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 8-SOIC（0.154"，3.90mm 宽） |
| 供应商设备封装： | 8-SOIC |
| 包装： | 管件 |
X4163, X4165
Figure 10. Writing 12-bytes to a 64-byte page starting at location 60.
8 Bytes
4 Bytes
Address
=7
Address Pointer
Ends Here
Addr = 8
Address
60
Address
n-1
The master terminates the Data Byte loading by issuing
a stop condition, which causes the device to begin the
nonvolatile write cycle. As with the byte write operation,
all inputs are disabled until completion of the internal
write cycle. See Figure 9 for the address, acknowledge,
and data transfer sequence.
Stops and Write Modes
Stop conditions that terminate write operations must
Figure 11. Acknowledge Polling Sequence
Byte load completed
by issuing STOP.
Enter ACK Polling
Issue START
be sent by the master after sending at least 1 full data
byte plus the subsequent ACK signal. If a stop is
issued in the middle of a data byte, or before 1 full
data byte plus its associated ACK is sent, then the
device will reset itself without performing the write. The
contents of the array will not be effected.
Acknowledge Polling
The disabling of the inputs during nonvolatile cycles
Issue Slave Address
Byte (Read or Write)
ACK
returned?
YES
NO
Issue STOP
can be used to take advantage of the typical 5ms write
cycle time. Once the stop condition is issued to indi-
cate the end of the master’s byte load operation, the
Nonvolatile Cycle
complete. Continue
command sequence?
NO
Issue STOP
device initiates the internal nonvolatile cycle. Acknowl-
edge polling can be initiated immediately. To do this,
the master issues a start condition followed by the
Slave Address Byte for a write or read operation. If the
device is still busy with the nonvolatile cycle then no
ACK will be returned. If the device has completed the
write operation, an ACK will be returned and the host
can then proceed with the read or write operation.
Refer to the flow chart in Figure 11.
12
YES
Continue Normal
Read or Write
Command Sequence
PROCEED
FN8120.2
November 26, 2007
相关PDF资料 |
PDF描述 |
|---|---|
| RCE30DHFT | CONN EDGECARD 60POS 1MM SMD |
| 400VXR120MEFCSN25X30 | CAP ALUM 120UF 400V 20% SNAP-IN |
| MIC5236YM | IC REG LDO ADJ .15A 8SOIC |
| MIC5236-5.0YM | IC REG LDO 5V .15A 8-SOIC |
| RBC65DREN | CONN EDGECARD 130PS .100 EYELET |
相关代理商/技术参数 |
参数描述 |
|---|---|
| X4165S8I-2.7 | 功能描述:IC SUPERVISOR CPU 16K EE 8-SOIC RoHS:否 类别:集成电路 (IC) >> PMIC - 监控器 系列:- 标准包装:100 系列:- 类型:简单复位/加电复位 监视电压数目:1 输出:- 复位:低有效 复位超时:最小为 100 ms 电压 - 阀值:4.38V 工作温度:0°C ~ 70°C 安装类型:表面贴装 封装/外壳:8-TSSOP（0.173"，4.40mm 宽） 供应商设备封装:8-TSSOP 包装:管件 |
| X4165S8I-2.7A | 功能描述:IC SUPERVISOR CPU 16K EE 8-SOIC RoHS:否 类别:集成电路 (IC) >> PMIC - 监控器 系列:- 标准包装:100 系列:- 类型:简单复位/加电复位 监视电压数目:1 输出:- 复位:低有效 复位超时:最小为 100 ms 电压 - 阀值:4.38V 工作温度:0°C ~ 70°C 安装类型:表面贴装 封装/外壳:8-TSSOP（0.173"，4.40mm 宽） 供应商设备封装:8-TSSOP 包装:管件 |
| X4165S8I-4.5A | 功能描述:IC SUPERVISOR CPU 16K EE 8-SOIC RoHS:否 类别:集成电路 (IC) >> PMIC - 监控器 系列:- 标准包装:100 系列:- 类型:简单复位/加电复位 监视电压数目:1 输出:- 复位:低有效 复位超时:最小为 100 ms 电压 - 阀值:4.38V 工作温度:0°C ~ 70°C 安装类型:表面贴装 封装/外壳:8-TSSOP（0.173"，4.40mm 宽） 供应商设备封装:8-TSSOP 包装:管件 |
| X4165S8T1 | 功能描述:IC SUPERVISOR CPU 16K EE 8-SOIC RoHS:否 类别:集成电路 (IC) >> PMIC - 监控器 系列:- 标准包装:100 系列:- 类型:简单复位/加电复位 监视电压数目:1 输出:- 复位:低有效 复位超时:最小为 100 ms 电压 - 阀值:4.38V 工作温度:0°C ~ 70°C 安装类型:表面贴装 封装/外壳:8-TSSOP（0.173"，4.40mm 宽） 供应商设备封装:8-TSSOP 包装:管件 |
| X4165S8ZT1 | 制造商:Intersil Corporation 功能描述:PROCESSOR SUPERVISOR 4.38V 3000UA 8SOIC - Tape and Reel |
发布紧急采购，3分钟左右您将得到回复。