- 您现在的位置：买卖IC网 > PDF目录13096 > X4165S8I (Intersil)IC CPU SUPRV 16K EE RST HI 8SOIC PDF资料下载
参数资料
| 型号： | X4165S8I |
| 厂商： | Intersil |
| 文件页数： | 13/22页 |
| 文件大小： | 0K |
| 描述： | IC CPU SUPRV 16K EE RST HI 8SOIC |
| 标准包装： | 200 |
| 类型： | 简单复位/加电复位 |
| 监视电压数目： | 1 |
| 输出： | 开路漏极或开路集电极 |
| 复位： | 高有效 |
| 复位超时： | 最小为 100 ms |
| 电压 - 阀值： | 4.38V |
| 工作温度： | -40°C ~ 85°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 8-SOIC（0.154"，3.90mm 宽） |
| 供应商设备封装： | 8-SOIC |
| 包装： | 管件 |
X4163, X4165
Figure 12. Current Address Read Sequence
Signals from
the Master
SDA Bus
Signals from
the Slave
S
t
a
r
t
Slave
Address
1 0 1 0
1
A
C
K
Data
S
t
o
p
Serial Read Operations
Read operations are initiated in the same manner as
write operations with the exception that the R/W bit of
the Slave Address Byte is set to one. There are three
basic read operations: Current Address Reads, Ran-
dom Reads, and Sequential Reads.
Current Address Read
Internally the device contains an address counter that
maintains the address of the last word read incre-
mented by one. Therefore, if the last read was to
address n, the next read operation would access data
from address n+1. On power up, the address of the
address counter is undefined, requiring a read or write
operation for initialization.
Upon receipt of the Slave Address Byte with the R/W
bit set to one, the device issues an acknowledge and
then transmits the eight bits of the Data Byte. The
master terminates the read operation when it does not
respond with an acknowledge during the ninth clock
and then issues a stop condition. Refer to Figure 12
for the address, acknowledge, and data transfer
sequence.
It should be noted that the ninth clock cycle of the read
operation is not a “don’t care.” To terminate a read
operation, the master must either issue a stop condi-
tion during the ninth cycle or hold SDA HIGH during
the ninth clock cycle and then issue a stop condition.
Figure 13. Random Address Read Sequence
Random Read
Random read operation allows the master to access
any memory location in the array. Prior to issuing the
Slave Address Byte with the R/W bit set to one, the
master must first perform a “dummy” write operation.
The master issues the start condition and the Slave
Address Byte, receives an acknowledge, then issues
the Word Address Bytes. After acknowledging receipts
of the Word Address Bytes, the master immediately
issues another start condition and the Slave Address
Byte with the R/W bit set to one. This is followed by an
acknowledge from the device and then by the eight bit
word. The master terminates the read operation by not
responding with an acknowledge and then issuing a
stop condition. Refer to Figure 13 for the address,
acknowledge, and data transfer sequence.
There is a similar operation, called “Set Current
Address” where the device does no operation, but
enters a new address into the address counter if a
stop is issued instead of the second start shown in Fig-
ure 13. The device goes into standby mode after the
stop and all bus activity will be ignored until a start is
detected. The next Current Address Read operation
reads from the newly loaded address. This operation
could be useful if the master knows the next address it
needs to read, but is not ready for the data.
Signals from
the Master
S
t
a
r
t
Slave
Address
Word Address
Byte 1
Word Address
Byte 0
S
t
a
r
t
Slave
Address
S
t
o
p
SDA Bus
1 0 1 0
0
1
Signals from
the Slave
A
C
K
A
C
K
A
C
K
A
C
K
Data
13
FN8120.2
November 26, 2007
相关PDF资料 |
PDF描述 |
|---|---|
| RCE30DHFT | CONN EDGECARD 60POS 1MM SMD |
| 400VXR120MEFCSN25X30 | CAP ALUM 120UF 400V 20% SNAP-IN |
| MIC5236YM | IC REG LDO ADJ .15A 8SOIC |
| MIC5236-5.0YM | IC REG LDO 5V .15A 8-SOIC |
| RBC65DREN | CONN EDGECARD 130PS .100 EYELET |
相关代理商/技术参数 |
参数描述 |
|---|---|
| X4165S8I-2.7 | 功能描述:IC SUPERVISOR CPU 16K EE 8-SOIC RoHS:否 类别:集成电路 (IC) >> PMIC - 监控器 系列:- 标准包装:100 系列:- 类型:简单复位/加电复位 监视电压数目:1 输出:- 复位:低有效 复位超时:最小为 100 ms 电压 - 阀值:4.38V 工作温度:0°C ~ 70°C 安装类型:表面贴装 封装/外壳:8-TSSOP（0.173"，4.40mm 宽） 供应商设备封装:8-TSSOP 包装:管件 |
| X4165S8I-2.7A | 功能描述:IC SUPERVISOR CPU 16K EE 8-SOIC RoHS:否 类别:集成电路 (IC) >> PMIC - 监控器 系列:- 标准包装:100 系列:- 类型:简单复位/加电复位 监视电压数目:1 输出:- 复位:低有效 复位超时:最小为 100 ms 电压 - 阀值:4.38V 工作温度:0°C ~ 70°C 安装类型:表面贴装 封装/外壳:8-TSSOP（0.173"，4.40mm 宽） 供应商设备封装:8-TSSOP 包装:管件 |
| X4165S8I-4.5A | 功能描述:IC SUPERVISOR CPU 16K EE 8-SOIC RoHS:否 类别:集成电路 (IC) >> PMIC - 监控器 系列:- 标准包装:100 系列:- 类型:简单复位/加电复位 监视电压数目:1 输出:- 复位:低有效 复位超时:最小为 100 ms 电压 - 阀值:4.38V 工作温度:0°C ~ 70°C 安装类型:表面贴装 封装/外壳:8-TSSOP（0.173"，4.40mm 宽） 供应商设备封装:8-TSSOP 包装:管件 |
| X4165S8T1 | 功能描述:IC SUPERVISOR CPU 16K EE 8-SOIC RoHS:否 类别:集成电路 (IC) >> PMIC - 监控器 系列:- 标准包装:100 系列:- 类型:简单复位/加电复位 监视电压数目:1 输出:- 复位:低有效 复位超时:最小为 100 ms 电压 - 阀值:4.38V 工作温度:0°C ~ 70°C 安装类型:表面贴装 封装/外壳:8-TSSOP（0.173"，4.40mm 宽） 供应商设备封装:8-TSSOP 包装:管件 |
| X4165S8ZT1 | 制造商:Intersil Corporation 功能描述:PROCESSOR SUPERVISOR 4.38V 3000UA 8SOIC - Tape and Reel |
发布紧急采购，3分钟左右您将得到回复。