- 您现在的位置：买卖IC网 > PDF目录13090 > X4285V8I (Intersil)IC SUPERV 128K EE RST HI 8TSSOP PDF资料下载
参数资料
| 型号： | X4285V8I |
| 厂商： | Intersil |
| 文件页数： | 6/22页 |
| 文件大小： | 0K |
| 描述： | IC SUPERV 128K EE RST HI 8TSSOP |
| 标准包装： | 200 |
| 类型： | 简单复位/加电复位 |
| 监视电压数目： | 1 |
| 复位： | 高有效 |
| 复位超时： | 最小为 100 ms |
| 电压 - 阀值： | 4.38V |
| 工作温度： | -40°C ~ 85°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 8-TSSOP（0.173"，4.40mm 宽） |
| 供应商设备封装： | 8-TSSOP |
| 包装： | 管件 |
X4283, X4285
Setting the V TRIP Voltage
This procedure is used to set the V TRIP to a higher or
lower voltage value. It is necessary to reset the trip
point before setting the new value.
To set the new V TRIP voltage, start by setting the WEL
bit in the control register, then apply the desired V TRIP
threshold voltage to the V CC pin and the programming
voltage, V P , to the WP pin and 2 byte address and 1
byte of “00” data. The stop bit following a valid write
operation initiates the V TRIP programming sequence.
Bring WP LOW to complete the operation.
Resetting the V TRIP Voltage
This procedure is used to set the V TRIP to a “native”
voltage level. For example, if the current V TRIP is 4.4V
and the new V TRIP must be 4.0V, then the V TRIP must
be reset. When V TRIP is reset, the new V TRIP is some-
thing less than 1.7V. This procedure must be used to
set the voltage to a lower value.
To reset the new V TRIP voltage start by setting the
WEL bit in the control register, apply V CC and the pro-
gramming voltage, V P , to the WP pin and 2 byte
address and 1 byte of “00” data. The stop bit of a valid
write operation initiates the V TRIP programming
sequence. Bring WP LOW to complete the operation.
Figure 2. Reset V TRIP Level Sequence (V CC > 3V. WP = 12-15V, WEL bit set)
WP
V P = 12-15V
0 1 2 3 4 5 6 7
0 1 2 3 4 5 6 7
0 1 2 3 4 5 6 7
0 1 2 3 4 5 6 7
SCL
SDA
A0h
00h
03h
00h
Figure 3. Sample V TRIP Reset Circuit
V P
V TRIP
Adj.
RESET
4.7K
1
2
3
4
SOIC
X4283
8
7
6
5
Adjust
Run
SCL
μC
SDA
6
FN8121.1
May 23, 2006
相关PDF资料 |
PDF描述 |
|---|---|
| 80ZLJ1200M18X40 | CAP ALUM 1200UF 80V 20% RADIAL |
| 1812-822J | INDUCTOR UNSHIELDED 8.2UH SMD |
| ASM22DRTI-S13 | CONN EDGECARD 44POS .156 EXTEND |
| MIC5236-3.3YMM | IC REG LDO 3.3V .15A 8-MSOP |
| X4285V8-2.7 | IC SUPERV 128K EE RST HI 8TSSOP |
相关代理商/技术参数 |
参数描述 |
|---|---|
| X4285V8I-2.7 | 功能描述:IC SUPERV 128K EE RST HI 8TSSOP RoHS:否 类别:集成电路 (IC) >> PMIC - 监控器 系列:- 标准包装:1 系列:- 类型:简单复位/加电复位 监视电压数目:1 输出:开路漏极或开路集电极 复位:低有效 复位超时:标准传输延迟为 60 µs 电压 - 阀值:3V 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:SC-74A，SOT-753 供应商设备封装:SOT-23-5 包装:Digi-Reel® 其它名称:LM8364BALMF30DKR |
| X4285V8I-2.7A | 功能描述:IC SUPERVISOR CPU 128K EE 8TSSOP RoHS:否 类别:集成电路 (IC) >> PMIC - 监控器 系列:- 标准包装:100 系列:- 类型:简单复位/加电复位 监视电压数目:1 输出:- 复位:低有效 复位超时:最小为 100 ms 电压 - 阀值:4.38V 工作温度:0°C ~ 70°C 安装类型:表面贴装 封装/外壳:8-TSSOP（0.173"，4.40mm 宽） 供应商设备封装:8-TSSOP 包装:管件 |
| X4285V8I-4.5A | 功能描述:IC SUPERVISOR CPU 128K EE 8TSSOP RoHS:否 类别:集成电路 (IC) >> PMIC - 监控器 系列:- 标准包装:100 系列:- 类型:简单复位/加电复位 监视电压数目:1 输出:- 复位:低有效 复位超时:最小为 100 ms 电压 - 阀值:4.38V 工作温度:0°C ~ 70°C 安装类型:表面贴装 封装/外壳:8-TSSOP（0.173"，4.40mm 宽） 供应商设备封装:8-TSSOP 包装:管件 |
| X-428796A | 制造商:Volex Group 功能描述:LEAD BLACK 2.5M AUSTRALIAN 制造商:Volex Group 功能描述:LEAD, BLACK, 2.5M, AUSTRALIAN |
| X-428802A | 制造商:Volex Group 功能描述:LEAD HOT CONDITION BLACK 2M 制造商:Volex Group 功能描述:LEAD, HOT CONDITION, BLACK, 2M 制造商:Volex Group 功能描述:LEAD, HOT CONDITION, BLACK, 2M; Connector Type A:IEC Socket; Connector Type B:Wire; Voltage Rating:250V; Current Rating:10A; Cable Length - Imperial:6.56ft; Cable Length - Metric:2m; Jacket Colour:Black; SVHC:No SVHC (18-Jun-2012); ;RoHS Compliant: Yes |
发布紧急采购，3分钟左右您将得到回复。