参数资料
| 型号： | X5163PI-4.5A |
| 厂商： | Intersil |
| 文件页数： | 5/21页 |
| 文件大小： | 0K |
| 描述： | IC SUPERVISOR CPU 16K EE 8-DIP |
| 标准包装： | 50 |
| 类型： | 简单复位/加电复位 |
| 监视电压数目： | 1 |
| 输出： | 开路漏极或开路集电极 |
| 复位： | 低有效 |
| 复位超时： | 最小为 100 ms |
| 电压 - 阀值： | 4.63V |
| 工作温度： | -40°C ~ 85°C |
| 安装类型： | 通孔 |
| 封装/外壳： | 8-DIP（0.300"，7.62mm） |
| 供应商设备封装： | 8-PDIP |
| 包装： | 管件 |
X5163, X5165
Principles Of Operation
Power-on Reset
Application of power to the X5163, X5165 activates a Power-
on Reset Circuit. This circuit goes active at 1V and pulls the
RESET/RESET pin active. This signal prevents the system
microprocessor from starting to operate with insufficient
voltage or prior to stabilization of the oscillator. When V CC
exceeds the device V TRIP value for 200ms (nominal) the
circuit releases RESET/RESET, allowing the processor to
begin executing code.
Low Voltage Monitoring
During operation, the X5163, X5165 monitors the V CC level
and asserts RESET/RESET if supply voltage falls below a
preset minimum V TRIP . The RESET/RESET signal prevents
the microprocessor from operating in a power fail or
brownout condition. The RESET/RESET signal remains
active until the voltage drops below 1V. It also remains active
until V CC returns and exceeds V TRIP for 200ms.
Watchdog Timer
The Watchdog Timer circuit monitors the microprocessor
activity by monitoring the WDI input. The microprocessor
must toggle the CS/WDI pin periodically to prevent a
RESET/RESET signal. The CS/WDI pin must be toggled
from HIGH to LOW prior to the expiration of the watchdog
time out period. The state of two nonvolatile control bits in
the Status Register determine the watchdog timer period.
The microprocessor can change these watchdog bits, or
they may be “locked” by tying the WP pin LOW and setting
the WPEN bit HIGH.
V CC Threshold Reset Procedure
The X5163, X5165 has a standard V CC threshold (V TRIP )
voltage. This value will not change over normal operating
To set the new V TRIP voltage, apply th e desired V TRIP
threshold to the V CC pin and tie the CS/WDI pin and the WP
pin HIGH. RESET and SO pins are left unconnected. Then
apply the programming voltage V P to both SCK and SI and
pulse CS/WDI LOW then HIGH. Remove V P and the
sequence is complete.
CS
V P
SCK
V P
SI
FIGURE 1. SET V TRIP VOLTAGE
Resetting the V TRIP Voltage
This procedure sets the V TRIP to a “native” voltage level. For
example, if the current V TRIP is 4.4V and the V TRIP is reset,
the new V TRIP is something less than 1.7V. This procedure
must be used to set the voltage to a lower value.
To reset the V TRIP voltage, apply a voltage between 2.7 and
5.5V to the V CC pin. Tie the CS/WDI pin, the WP pin, AND
THE SCK pin HIGH. RESET and SO pins are left
unconnected. Then apply the programming voltage V P to the
SI pin ONLY and pulse CS/WDI LOW then HIGH. Remove V P
and the sequence is complete.
CS
and storage conditions. However, in applications where the
standard V TRIP is not exactly right, or for higher precision in
SCK
V CC
the V TRIP value, the X5163, X5165 threshold may be
adjusted.
Setting the V TRIP Voltage
This procedure sets the V TRIP to a higher voltage value. For
example, if the current V TRIP is 4.4V and the new V TRIP is
4.6V, this procedure directly makes the change. If the new
setting is lower than the current setting, then it is necessary
to reset the trip point before setting the new value.
5
SI
V P
FIGURE 2. RESET V TRIP VOLTAGE
FN8128.3
June 1, 2006
相关PDF资料 |
PDF描述 |
|---|---|
| X5163PI-2.7A | IC SUPERVISOR CPU 16K EE 8-DIP |
| EBM44DSAI | CONN EDGECARD 88POS R/A .156 SLD |
| X5163PI-2.7 | IC SUPERVISOR CPU 16K EE 8-DIP |
| X5163PI | IC SUPERVISOR CPU 16K EE 8-DIP |
| X5163P-4.5A | IC SUPERVISOR CPU 16K EE 8-DIP |
相关代理商/技术参数 |
参数描述 |
|---|---|
| X5163PIZ | 功能描述:IC CPU SUPERV 16K EEPROM 8-PDIP RoHS:是 类别:集成电路 (IC) >> PMIC - 监控器 系列:- 产品培训模块:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 标准包装:2,500 系列:- 类型:简单复位/加电复位 监视电压数目:1 输出:开路漏极或开路集电极 复位:低有效 复位超时:最小为 600 ms 电压 - 阀值:3.8V 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:SC-74A，SOT-753 供应商设备封装:SOT-23-5 包装:带卷 (TR) |
| X5163PIZ-2.7 | 功能描述:IC CPU SUPERV 16K EEPROM 8-PDIP RoHS:是 类别:集成电路 (IC) >> PMIC - 监控器 系列:- 产品培训模块:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 标准包装:2,500 系列:- 类型:简单复位/加电复位 监视电压数目:1 输出:开路漏极或开路集电极 复位:低有效 复位超时:最小为 600 ms 电压 - 阀值:3.8V 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:SC-74A，SOT-753 供应商设备封装:SOT-23-5 包装:带卷 (TR) |
| X5163PIZ-2.7A | 功能描述:IC CPU SUPERV 16K EEPROM 8-PDIP RoHS:是 类别:集成电路 (IC) >> PMIC - 监控器 系列:- 产品培训模块:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 标准包装:2,500 系列:- 类型:简单复位/加电复位 监视电压数目:1 输出:开路漏极或开路集电极 复位:低有效 复位超时:最小为 600 ms 电压 - 阀值:3.8V 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:SC-74A，SOT-753 供应商设备封装:SOT-23-5 包装:带卷 (TR) |
| X5163PIZ-4.5A | 功能描述:IC CPU SUPERV 16K EEPROM 8-PDIP RoHS:是 类别:集成电路 (IC) >> PMIC - 监控器 系列:- 产品培训模块:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 标准包装:2,500 系列:- 类型:简单复位/加电复位 监视电压数目:1 输出:开路漏极或开路集电极 复位:低有效 复位超时:最小为 600 ms 电压 - 阀值:3.8V 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:SC-74A，SOT-753 供应商设备封装:SOT-23-5 包装:带卷 (TR) |
| X5163PZ | 功能描述:IC CPU SUPERV 16K EEPROM 8-PDIP RoHS:是 类别:集成电路 (IC) >> PMIC - 监控器 系列:- 产品培训模块:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 标准包装:2,500 系列:- 类型:简单复位/加电复位 监视电压数目:1 输出:开路漏极或开路集电极 复位:低有效 复位超时:最小为 600 ms 电压 - 阀值:3.8V 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:SC-74A，SOT-753 供应商设备封装:SOT-23-5 包装:带卷 (TR) |
发布紧急采购，3分钟左右您将得到回复。