参数资料
| 型号： | X5323P-2.7 |
| 厂商： | Intersil |
| 文件页数： | 9/20页 |
| 文件大小： | 0K |
| 描述： | IC SUPERVISOR CPU 32K EE 8-DIP |
| 标准包装： | 50 |
| 类型： | 简单复位/加电复位 |
| 监视电压数目： | 1 |
| 输出： | 开路漏极或开路集电极 |
| 复位： | 低有效 |
| 复位超时： | 最小为 100 ms |
| 电压 - 阀值： | 2.63V |
| 工作温度： | 0°C ~ 70°C |
| 安装类型： | 通孔 |
| 封装/外壳： | 8-DIP（0.300"，7.62mm） |
| 供应商设备封装： | 8-PDIP |
| 包装： | 管件 |
X5323, X5325
When the highest address is reached, the address counter
rolls over to address $0000 allowing the read cycle to be
continued indefinitely. The read operation is terminated by
taking CS high. Refer to the read EEPROM Array Sequence
(Figure 1).
To read the status register, the CS line is first pulled low to
select the device followed by the 8-bit RDSR instruction.
After the RDSR opcode is sent, the contents of the status
register are shifted out on the SO line. Refer to the read
status register sequence (Figure 2).
Write Sequence
Prior to any attempt to write data into the device, the “Write
Enable” Latch (WEL) must first be set by issuing the WREN
instruction (Figure 3). CS is first taken LOW, then the WREN
instruction is clocked into the device. After all eight bits of the
instruction are transmitted, CS must then be taken HIGH. If
the user continues the write operation without taking CS
HIGH after issuing the WREN instruction, the write operation
will be ignored.
To write data to the EEPROM memory array, the user then
issues the WRITE instruction followed by the 16-bit address
and then the data to be written. Any unused address bits are
specified to be “0’s”. The WRITE operation minimally takes
32 clocks. CS must go low and remain low for the duration of
the operation. If the address counter reaches the end of a
page and the clock continues, the counter will roll back to the
first address of the page and overwrite any data that may
have been previously written.
Note: When writing more than one page, you must wait one
write cycle (10ms typical) when going from one page to
another. This is required for the internal nonvolatile memory
to be programmed correctly.
CS
For the page write operation (byte or page write) to be
completed, CS can only be brought HIGH after bit 0 of the
last data byte to be written is clocked in. If it is brought HIGH
at any other time, the write operation will not be completed
(Figure 4).
To write to the status register, the WRSR instruction is
followed by the data to be written (Figure 5). Data bits 0 and
1 must be “0”.
While the write is in progress following a status register or
EEPROM Sequence, the status register may be read to
check the WIP bit. During this time the WIP bit will be high.
Operational Notes
The device powers-up in the following state:
? The device is in the low power standby state.
? A HIGH to LOW transition on CS is required to enter an
active state and receive an instruction.
? SO pin is high impedance.
? The write enable latch is reset.
? The flag bit is reset.
? Reset signal is active for t PURST .
Data Protection
The following circuitry has been included to prevent
inadvertent writes:
? A WREN instruction must be issued to set the write enable
latch.
? CS must come HIGH at the proper clock count in order to
start a nonvolatile write cycle.
0
1
2
3
4
5
6
7
8
9
10
11
12
13
14
SCK
INSTRUCTION
SI
DATA OUT
SO
HIGH IMPEDANCE
7
6
5
4
3
2
1
0
MSB
FIGURE 6. READ STATUS REGISTER SEQUENCE
9
FN8131.2
June 30, 2008
相关PDF资料 |
PDF描述 |
|---|---|
| GCM36DRSN-S664 | CONN EDGECARD 72POS DIP .156 SLD |
| X5323P | IC SUPERVISOR CPU 32K EE 8-DIP |
| RSC18DRTF-S13 | CONN EDGECARD 36POS .100 EXTEND |
| GCM36DRSD-S664 | CONN EDGECARD 72POS DIP .156 SLD |
| GCM36DRMN-S664 | CONN EDGECARD 72POS .156 WW |
相关代理商/技术参数 |
参数描述 |
|---|---|
| X5323P-4.5A | 功能描述:IC SUPERVISOR CPU 32K EE 8-DIP RoHS:否 类别:集成电路 (IC) >> PMIC - 监控器 系列:- 产品培训模块:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 标准包装:2,500 系列:- 类型:简单复位/加电复位 监视电压数目:1 输出:推挽式，图腾柱 复位:低有效 复位超时:最小 145 ms 电压 - 阀值:2.64V 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:16-WQFN 裸露焊盘 供应商设备封装:16-TQFN-EP（4x4） 包装:带卷 (TR) |
| X5323PI | 功能描述:IC SUPERVISOR CPU 32K EE 8-DIP RoHS:否 类别:集成电路 (IC) >> PMIC - 监控器 系列:- 产品培训模块:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 标准包装:2,500 系列:- 类型:简单复位/加电复位 监视电压数目:1 输出:推挽式，图腾柱 复位:低有效 复位超时:最小 145 ms 电压 - 阀值:2.64V 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:16-WQFN 裸露焊盘 供应商设备封装:16-TQFN-EP（4x4） 包装:带卷 (TR) |
| X5323PI-2.7 | 功能描述:IC SUPERVISOR CPU 32K EE 8-DIP RoHS:否 类别:集成电路 (IC) >> PMIC - 监控器 系列:- 产品培训模块:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 标准包装:2,500 系列:- 类型:简单复位/加电复位 监视电压数目:1 输出:推挽式，图腾柱 复位:低有效 复位超时:最小 145 ms 电压 - 阀值:2.64V 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:16-WQFN 裸露焊盘 供应商设备封装:16-TQFN-EP（4x4） 包装:带卷 (TR) |
| X5323PI-2.7A | 功能描述:IC SUPERVISOR CPU 32K EE 8-DIP RoHS:否 类别:集成电路 (IC) >> PMIC - 监控器 系列:- 产品培训模块:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 标准包装:2,500 系列:- 类型:简单复位/加电复位 监视电压数目:1 输出:推挽式，图腾柱 复位:低有效 复位超时:最小 145 ms 电压 - 阀值:2.64V 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:16-WQFN 裸露焊盘 供应商设备封装:16-TQFN-EP（4x4） 包装:带卷 (TR) |
| X5323PI-4.5A | 功能描述:IC SUPERVISOR CPU 32K EE 8-DIP RoHS:否 类别:集成电路 (IC) >> PMIC - 监控器 系列:- 产品培训模块:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 标准包装:2,500 系列:- 类型:简单复位/加电复位 监视电压数目:1 输出:推挽式，图腾柱 复位:低有效 复位超时:最小 145 ms 电压 - 阀值:2.64V 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:16-WQFN 裸露焊盘 供应商设备封装:16-TQFN-EP（4x4） 包装:带卷 (TR) |
发布紧急采购，3分钟左右您将得到回复。