参数资料
| 型号： | X9420WP16Z |
| 厂商： | Intersil |
| 文件页数： | 15/19页 |
| 文件大小： | 0K |
| 描述： | IC DGTL POT 1CH 16PDIP |
| 标准包装： | 30 |
| 系列： | XDCP™ |
| 接片： | 64 |
| 电阻（欧姆）： | 10k |
| 电路数： | 1 |
| 温度系数： | 标准值 ±300 ppm/°C |
| 存储器类型： | 非易失 |
| 接口： | 5 线 SPI（芯片选择，设备位址） |
| 电源电压： | 4.5 V ~ 5.5 V |
| 工作温度： | 0°C ~ 70°C |
| 安装类型： | 通孔 |
| 封装/外壳： | 16-DIP（0.300"，7.62mm） |
| 供应商设备封装： | 16-DIP |
| 包装： | 管件 |
5
FN8195.1
April 26, 2006
Figure 1. Detailed Potentiometer Block Diagram
Write in Process
The contents of the Data Registers are saved to
nonvolatile memory when the CS pin goes from LOW to
HIGH after a complete write sequence is received by
the device. The progress of this internal write operation
can be monitored by a Write In Process bit (WIP). The
WIP bit is read with a Read Status command.
INSTRUCTIONS
Address/Identification (ID) Byte
The first byte sent to the X9420 from the host,
following a CS going HIGH to LOW, is called the
Address or Identification byte. The most significant
four bits of the slave address are a device type
identifier, for the X9420 this is fixed as 0101[B] (refer
to Figure 2).
The least significant bit in the ID byte selects one of
two devices on the bus. The physical device address
is defined by the state of the A0 input pin. The X9420
compares the serial data stream with the address
input state; a successful compare of the address bit is
required for the X9420 to successfully continue the
command sequence. The A0 input can be actively
driven by a CMOS input signal or tied to VCC or VSS.
The remaining three bits in the ID byte must be set to 110.
Figure 2. Address/Identification Byte Format
Instruction Byte
The next byte sent to the X9420 contains the
instruction and register pointer information. The four
most significant bits are the instruction. The next two
bits point to one of four data registers. The format is
shown below in Figure 3.
Figure 3. Instruction Byte Format
Serial Data Path
From Interface
Circuitry
Register 0
Register 1
REGISTER 2
REGISTER 3
Serial
Bus
Input
Parallel
Bus
Input
Counter
Register
INC/DEC
Logic
UP/DN
CLK
Modified SCK
UP/DN
VH
VL
VW
8
6
C
O
U
N
T
E
R
D
E
C
O
D
E
IF WCR = 00[H] THEN VW = VL
IF WCR = 3F[H] THEN VW = VH
Wiper
(WCR)
1
00
11
0A0
Device Type
Identifier
Device Address
1
I1
I2
I3
I0
R1
R0
0
Register
Select
Instructions
X9420
相关PDF资料 |
PDF描述 |
|---|---|
| MS3108A28-18S | CONN PLUG 12POS RT ANG W/SCKT |
| MS27472E18B96P | CONN RCPT 9POS WALL MT W/PINS |
| VE-J1F-MZ-S | CONVERTER MOD DC/DC 72V 25W |
| MS3108E28-10P | CONN PLUG 7POS RT ANG W/PINS |
| MS27468E25F35PB | CONN RCPT 128POS JAM NUT W/PINS |
相关代理商/技术参数 |
参数描述 |
|---|---|
| X9420WP-2.7 | 制造商:XICOR 制造商全称:Xicor Inc. 功能描述:Single Digitally Controlled (XDCP) Potentiometer |
| X9420WPI | 制造商:XICOR 制造商全称:Xicor Inc. 功能描述:Single Digitally Controlled (XDCP) Potentiometer |
| X9420WPI-2.7 | 制造商:XICOR 制造商全称:Xicor Inc. 功能描述:Single Digitally Controlled (XDCP) Potentiometer |
| X9420WPM | 制造商:XICOR 制造商全称:Xicor Inc. 功能描述:Single Digitally Controlled (XDCP) Potentiometer |
| X9420WPM-2.7 | 制造商:XICOR 制造商全称:Xicor Inc. 功能描述:Single Digitally Controlled (XDCP) Potentiometer |
发布紧急采购，3分钟左右您将得到回复。