参数资料
| 型号： | X95840WV20IZ-2.7 |
| 厂商： | Intersil |
| 文件页数： | 13/13页 |
| 文件大小： | 0K |
| 描述： | IC XDCP QUAD 256TAP 10K 20-TSSOP |
| 标准包装： | 75 |
| 系列： | XDCP™ |
| 接片： | 256 |
| 电阻（欧姆）： | 10k |
| 电路数： | 4 |
| 温度系数： | 标准值 ±45 ppm/°C |
| 存储器类型： | 非易失 |
| 接口： | I²C（设备位址） |
| 电源电压： | 2.7 V ~ 5.5 V |
| 工作温度： | -40°C ~ 85°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 20-TSSOP（0.173"，4.40mm 宽） |
| 供应商设备封装： | 20-TSSOP |
| 包装： | 管件 |
9
FN8213.2
July 5, 2006
Principles of Operation
The X95840 in as integrated circuit incorporating four DCPs
with their associated registers, non-volatile memory, and a
I2C serial interface providing direct communication between
a host and the potentiometers and memory.
DCP Description
Each DCP is implemented with a combination of resistor
elements and CMOS switches. The physical ends of each
DCP are equivalent to the fixed terminals of a mechanical
potentiometer (RH and RL pins). The RW pin of each DCP is
connected to intermediate nodes, and is equivalent to the
wiper terminal of a mechanical potentiometer. The position
of the wiper terminal within the DCP is controlled by an 8-bit
volatile Wiper Register (WR). Each DCP has its own WR.
When the WR of a DCP contains all zeroes (WR<7:0>: 00h),
its wiper terminal (RW) is closest to its “Low” terminal (RL).
When the WR of a DCP contains all ones (WR<7:0>: FFh),
its wiper terminal (RW) is closest to its “High” terminal (RH).
As the value of the WR increases from all zeroes (00h) to all
ones (255 decimal), the wiper moves monotonically from the
position closest to RL to the closest to RH. At the same time,
the resistance between RW and RL increases monotonically,
while the resistance between RH and RW decreases
monotonically.
While the X95840 is being powered up, all four WRs are
reset to 80h (128 decimal), which locates RW roughly at the
center between RL and RH. Soon after the power supply
voltage becomes large enough for reliable non-volatile
memory reading, the X95840 reads the value stored on four
different non-volatile Initial Value Registers (IVRs) and loads
them into their corresponding WRs.
The WRs and IVRs can be read or written directly using the
I2C serial interface as described in the following sections.
Memory Description
The X95840 contains eight non-volatile bytes. they are
accessed by I2C interface operations with Address Bytes 0
through 7 decimal. The first four non-volatile bytes at
addresses 0, 1, 2, and 3, contain the initial value loaded at
power-up into the volatile Wiper Registers (WRs) of DCP0,
DCP1, DCP2, and DCP3 respectively. Bytes at addresses 4,
5, and 6 are available to the user as general purpose
registers. The byte at address 7 is reserved; the user should
not write to it, and its value should be ignored if read.
The volatile WR, and the non-volatile Initial Value Register
(IVR) of a DCP are accessed with the same Address Byte.
A volatile byte at address 8 decimal, controls what byte is
read or written when accessing DCP registers: the WR, the
IVR, or both.
When the byte at address 8 is all zeroes, which is the default
at power up:
A read operation to addresses 0, 1, 2 or 3 outputs the
value of the non-volatile IVRs.
A write operation to addresses 0, 1, 2, or 3 writes the
same value to the WR and IVR of the corresponding DCP.
When the byte at address 8 is 80h (128 decimal):
A read operation to addresses 0, 1, 2, or 3 outputs the
value of the volatile WR.
A write operation to addresses 0, 1, 2, or 3 only writes to
the corresponding volatile WR.
It is not possible to write to an IVR without writing the same
value to its corresponding WR.
00h and 80h are the only values that should be written to
address 8. All other values are reserved and must not be
written to address 8.
To access the general purpose bytes at addresses 4, 5, or 6,
the value at address 8 must be all zeros.
FIGURE 13. MIDSCALE GLITCH, CODE 80h TO 7Fh (WIPER 0)
FIGURE 14. LARGE SIGNAL SETTLING TIME
Typical Performance Curves (Continued)
Wiper Movement Mid Point
From 80h to 7fh
Signal at Wiper (Wiper Unloaded)
SCL
Signal at Wiper
(Wiper Unloaded Movement
From ffh to 00h)
X95840
相关PDF资料 |
PDF描述 |
|---|---|
| ADG3241BKSZ-REEL | IC SW BUS 2.5-3.3V 1BIT SC70-6 |
| ADF4118BRUZ | IC PLL FREQ SYNTHESIZER 16-TSSOP |
| ADF4113BRUZ | IC SYNTH PLL RF 4.0GHZ 16-TSSOP |
| VI-BTW-MW-B1 | CONVERTER MOD DC/DC 5.5V 100W |
| X95840UV20IZ-2.7 | IC XDCP QUAD 256TAP 50K 20-TSSOP |
相关代理商/技术参数 |
参数描述 |
|---|---|
| X95RP-2 | 功能描述:消费电池与相机电池 D 18900mAh 2 PK Titanium Alkaline RoHS:否 制造商:FDK Batteries 电池大小:CR1/3N 输出电压:3 V 容量:160 mAh 化学性质:Lithium 端接类型:Pressure Contacts 可再充电/不可再充电:Non-Rechargeable |
| X95RP-4 | 功能描述:消费电池与相机电池 NOT AVAILABLE THROUGH MOUSER RoHS:否 制造商:FDK Batteries 电池大小:CR1/3N 输出电压:3 V 容量:160 mAh 化学性质:Lithium 端接类型:Pressure Contacts 可再充电/不可再充电:Non-Rechargeable |
| X96010 | 制造商:INTERSIL 制造商全称:Intersil Corporation 功能描述:Sensor Conditioner with Dual Look Up Table Memory and DACs |
| X96010V14I | 功能描述:CONDITIONER SGNL DUAL MEM & DAC RoHS:否 类别:集成电路 (IC) >> 接口 - 传感器和探测器接口 系列:- 其它有关文件:Automotive Product Guide 产品培训模块:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 标准包装:74 系列:- 类型:触控式传感器 输入类型:数字 输出类型:数字 接口:JTAG，串行 电流 - 电源:100µA 安装类型:表面贴装 封装/外壳:20-TSSOP（0.173"，4.40mm 宽） 供应商设备封装:20-TSSOP 包装:管件 |
| X96010V14IZ | 功能描述:板上安装温度传感器 SENSOR CONDITIONER W/DL LOOP UP TABLE RoHS:否 制造商:Omron Electronics 输出类型:Digital 配置: 准确性:+/- 1.5 C, +/- 3 C 温度阈值: 数字输出 - 总线接口:2-Wire, I2C, SMBus 电源电压-最大:5.5 V 电源电压-最小:4.5 V 最大工作温度:+ 50 C 最小工作温度:0 C 关闭: 安装风格: 封装 / 箱体: 设备功能:Temperature and Humidity Sensor |
发布紧急采购，3分钟左右您将得到回复。