参数资料
| 型号： | X95840WV20IZ-2.7 |
| 厂商： | Intersil |
| 文件页数： | 2/13页 |
| 文件大小： | 0K |
| 描述： | IC XDCP QUAD 256TAP 10K 20-TSSOP |
| 标准包装： | 75 |
| 系列： | XDCP™ |
| 接片： | 256 |
| 电阻（欧姆）： | 10k |
| 电路数： | 4 |
| 温度系数： | 标准值 ±45 ppm/°C |
| 存储器类型： | 非易失 |
| 接口： | I²C（设备位址） |
| 电源电压： | 2.7 V ~ 5.5 V |
| 工作温度： | -40°C ~ 85°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 20-TSSOP（0.173"，4.40mm 宽） |
| 供应商设备封装： | 20-TSSOP |
| 包装： | 管件 |
10
FN8213.2
July 5, 2006
The X95840 is pre-programed with 80h in the four IVRs.
WR: Wiper Register, IVR: Initial value Register.
I2C Serial Interface
The X95840 supports a bidirectional I2C bus oriented
protocol. The protocol defines any device that sends data
onto the bus as a transmitter and the receiving device as the
receiver. The device controlling the transfer is a master and
the device being controlled is the slave. The master always
initiates data transfers and provides the clock for both
transmit and receive operations. Therefore, the X95840
operates as a slave device in all applications.
All communication over the I2C interface is conducted by
sending the MSB of each byte of data first.
Protocol Conventions
Data states on the SDA line can change only during SCL
LOW periods. SDA state changes during SCL HIGH are
reserved for indicating START and STOP conditions (See
Figure 15). On power up of the X95840 the SDA pin is in the
input mode.
All I2C interface operations must begin with a START
condition, which is a HIGH to LOW transition of SDA while
SCL is HIGH. The X95840 continuously monitors the SDA
and SCL lines for the START condition and does not
respond to any command until this condition is met (See
Figure 15). A START condition is ignored during the power
up sequence and during internal non-volatile write cycles.
All I2C interface operations must be terminated by a STOP
condition, which is a LOW to HIGH transition of SDA while
SCL is HIGH (See Figure 15). A STOP condition at the end
of a read operation, or at the end of a write operation to
volatile bytes only places the device in its standby mode. A
STOP condition during a write operation to a non-volatile
byte, initiates an internal non-volatile write cycle. The device
enters its standby state when the internal non-volatile write
cycle is completed.
An ACK, Acknowledge, is a software convention used to
indicate a successful data transfer. The transmitting device,
either master or slave, releases the SDA bus after
transmitting eight bits. During the ninth clock cycle, the
receiver pulls the SDA line LOW to acknowledge the
reception of the eight bits of data (See Figure 16).
The X95840 responds with an ACK after recognition of a
START condition followed by a valid Identification Byte, and
once again after successful receipt of an Address Byte. The
X95840 also responds with an ACK after receiving a Data
Byte of a write operation. The master must respond with an
ACK after receiving a Data Byte of a read operation
A valid Identification Byte contains 1010 as the four MSBs,
and the following three bits matching the logic values
present at pins A2, A1, and A0. The LSB in the Read/Write
bit. Its value is “1” for a Read operation, and “0” for a Write
operation. See Table 2.
TABLE 2. IDENTIFICATION BYTE FORMAT
TABLE 1. MEMORY MAP
ADDRESS
NON-VOLATILE
VOLATILE
8
—
Access Control
7
Reserved
6
5
4
General Purpose
Not Available
3
2
1
0
IVR3
IVR2
IVR1
IVR0
WR3
WR2
WR1
WR0
1
0
1
0
A2
A1
A0
R/W
(MSB)
(LSB)
Logic values at pins A2, A1, and A0 respectively
SDA
SCL
START
DATA
STOP
STABLE
CHANGE
DATA
STABLE
FIGURE 15. VALID DATA CHANGES, START, AND STOP CONDITIONS
X95840
相关PDF资料 |
PDF描述 |
|---|---|
| ADG3241BKSZ-REEL | IC SW BUS 2.5-3.3V 1BIT SC70-6 |
| ADF4118BRUZ | IC PLL FREQ SYNTHESIZER 16-TSSOP |
| ADF4113BRUZ | IC SYNTH PLL RF 4.0GHZ 16-TSSOP |
| VI-BTW-MW-B1 | CONVERTER MOD DC/DC 5.5V 100W |
| X95840UV20IZ-2.7 | IC XDCP QUAD 256TAP 50K 20-TSSOP |
相关代理商/技术参数 |
参数描述 |
|---|---|
| X95RP-2 | 功能描述:消费电池与相机电池 D 18900mAh 2 PK Titanium Alkaline RoHS:否 制造商:FDK Batteries 电池大小:CR1/3N 输出电压:3 V 容量:160 mAh 化学性质:Lithium 端接类型:Pressure Contacts 可再充电/不可再充电:Non-Rechargeable |
| X95RP-4 | 功能描述:消费电池与相机电池 NOT AVAILABLE THROUGH MOUSER RoHS:否 制造商:FDK Batteries 电池大小:CR1/3N 输出电压:3 V 容量:160 mAh 化学性质:Lithium 端接类型:Pressure Contacts 可再充电/不可再充电:Non-Rechargeable |
| X96010 | 制造商:INTERSIL 制造商全称:Intersil Corporation 功能描述:Sensor Conditioner with Dual Look Up Table Memory and DACs |
| X96010V14I | 功能描述:CONDITIONER SGNL DUAL MEM & DAC RoHS:否 类别:集成电路 (IC) >> 接口 - 传感器和探测器接口 系列:- 其它有关文件:Automotive Product Guide 产品培训模块:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 标准包装:74 系列:- 类型:触控式传感器 输入类型:数字 输出类型:数字 接口:JTAG，串行 电流 - 电源:100µA 安装类型:表面贴装 封装/外壳:20-TSSOP（0.173"，4.40mm 宽） 供应商设备封装:20-TSSOP 包装:管件 |
| X96010V14IZ | 功能描述:板上安装温度传感器 SENSOR CONDITIONER W/DL LOOP UP TABLE RoHS:否 制造商:Omron Electronics 输出类型:Digital 配置: 准确性:+/- 1.5 C, +/- 3 C 温度阈值: 数字输出 - 总线接口:2-Wire, I2C, SMBus 电源电压-最大:5.5 V 电源电压-最小:4.5 V 最大工作温度:+ 50 C 最小工作温度:0 C 关闭: 安装风格: 封装 / 箱体: 设备功能:Temperature and Humidity Sensor |
发布紧急采购，3分钟左右您将得到回复。