- 您现在的位置：买卖IC网 > PDF目录19900 > XC18V512VQ44C (Xilinx Inc)IC PROM SRL CONFIG 512K 44-VQFP PDF资料下载
参数资料
| 型号： | XC18V512VQ44C |
| 厂商： | Xilinx Inc |
| 文件页数： | 22/24页 |
| 文件大小： | 0K |
| 描述： | IC PROM SRL CONFIG 512K 44-VQFP |
| 标准包装： | 160 |
| 可编程类型： | 系统内可编程 |
| 存储容量： | 512kb |
| 电源电压： | 3 V ~ 3.6 V |
| 工作温度： | 0°C ~ 70°C |
| 封装/外壳： | 44-TQFP |
| 供应商设备封装： | 44-VQFP（10x10） |
| 包装： | 托盘 |
| 其它名称： | 122-1241 XC18V512VQ44C-ND |
XC18V00 Series In-System-Programmable Configuration PROMs
DS026 (v5.2) January 11, 2008
Product Specification
7
R
IEEE 1149.1 Boundary-Scan (JTAG)
The XC18V00 family is fully compliant with the IEEE Std.
1149.1 Boundary-Scan, also known as JTAG. A Test
Access Port (TAP) and registers are provided to support all
required Boundary-Scan instructions, as well as many of
the optional instructions specified by IEEE Std. 1149.1. In
addition, the JTAG interface is used to implement in-system
programming (ISP) to facilitate configuration, erasure, and
verification operations on the XC18V00 device.
Table 4 lists the required and optional Boundary-Scan
instructions supported in the XC18V00. Refer to the IEEE Std.
1149.1 specification for a complete description of Boundary-
Scan architecture and the required and optional instructions.
Instruction Register
The Instruction Register (IR) for the XC18V00 is eight bits
wide and is connected between TDI and TDO during an
instruction scan sequence. In preparation for an instruction
scan sequence, the instruction register is parallel loaded with
a fixed instruction capture pattern. This pattern is shifted out
onto TDO (LSB first), while an instruction is shifted into the
instruction register from TDI. The detailed composition of the
instruction capture pattern is illustrated in Figure 3.
The ISP Status field, IR(4), contains logic “1” if the device is
currently in ISP mode; otherwise, it contains logic “0”. The
Security field, IR(3), contains logic “1” if the device has been
programmed with the security option turned on; otherwise, it
contains logic “0”.
X-Ref Target - Figure 3
Boundary-Scan Register
The Boundary-Scan register is used to control and observe
the
state
of
the
device
pins
during
the
EXTEST,
SAMPLE/PRELOAD, and CLAMP instructions. Each output
pin on the XC18V00 has two register stages that contribute
to the Boundary-Scan register, while each input pin only has
one register stage.
For each output pin, the register stage nearest to TDI controls
and observes the output state, and the second stage closest to
TDO controls and observes the high-Z enable state of the pin.
For each input pin, the register stage controls and observes
the input state of the pin.
Identification Registers
The IDCODE is a fixed, vendor-assigned value that is used
to electrically identify the manufacturer and type of the
device being addressed. The IDCODE register is 32 bits
wide. The IDCODE register can be shifted out for
examination by using the IDCODE instruction. The IDCODE
is available to any other system component via JTAG.
See Table 5 for the XC18V00 IDCODE values.
The IDCODE register has the following binary format:
vvvv:ffff:ffff:aaaa:aaaa:cccc:cccc:ccc1
where
v
= the die version number
f
= the family code (50h for XC18V00 family)
a
= the ISP PROM product ID (26h or 36h for the XC18V04)
c
= the company code (49h for Xilinx)
Note: The LSB of the IDCODE register is always read as logic “1”
as defined by IEEE Std. 1149.1.
Table 5 lists the IDCODE register values for XC18V00 devices.
Table 4: Boundary-Scan Instructions
Boundary-Scan
Command
Binary
Code [7:0]
Description
Required Instructions:
BYPASS
11111111
Enables BYPASS
SAMPLE/
PRELOAD
00000001
Enables Boundary-Scan
SAMPLE/PRELOAD
operation
EXTEST
00000000
Enables Boundary-Scan
EXTEST operation
Optional Instructions:
CLAMP
11111010
Enables Boundary-Scan
CLAMP operation
HIGHZ
11111100
All outputs in high-Z state
simultaneously
IDCODE
11111110
Enables shifting out
32-bit IDCODE
USERCODE
11111101
Enables shifting out
32-bit USERCODE
XC18V00 Specific Instructions:
CONFIG
11101110
Initiates FPGA configuration
by pulsing CF pin Low once
IR[7:5]
IR[4]
IR[3]
IR[2]
IR[1:0]
TDI
→
000
ISP
Status
Security
001(1)
→ TDO
Notes:
1.
IR[1:0] = 01 is specified by IEEE Std. 1149.1
Figure 3: Instruction Register Values Loaded into IR as
Part of an Instruction Scan Sequence
Table 5: IDCODES Assigned to XC18V00 Devices
ISP-PROM
IDCODE
XC18V01
05024093h
or
<v>5034093h
XC18V02
05025093h
or
<v>5035093h
XC18V04
05026093h
or
<v>5036093h
XC18V512
05023093h
or
<v>5033093h
Notes:
1.
The <v> in the IDCODE field represents the device’s revision
code (in hex), and may vary.
相关PDF资料 |
PDF描述 |
|---|---|
| 1235L3X2 | BATTERY PK S-HD 9.0V C SIZE ZINC |
| R-78AA5.0-1.0SMD-R | CONV DC/DC 1A 5V OUT SMD |
| GBM25DSXH | CONN EDGECARD 50POS DIP .156 SLD |
| AT17LV512-10JC | IC SER CFG PROM 512K 3.3V 20PLCC |
| NCV8506D2T33G | IC REG LDO 3.3V .4A D2PAK-7 |
相关代理商/技术参数 |
参数描述 |
|---|---|
| XC18V512VQ44C0936 | 制造商:Xilinx 功能描述:XLXXC18V512VQ44C0936 IC SYSTEM GATE |
| XC18V512VQ44I | 功能描述:IC PROM SER I-TEMP 3.3V 44-VQFP RoHS:否 类别:集成电路 (IC) >> 存储器 - 用于 FPGA 的配置 Proms 系列:- 产品变化通告:Product Discontinuation 28/Jul/2010 标准包装:98 系列:- 可编程类型:OTP 存储容量:300kb 电源电压:3 V ~ 3.6 V 工作温度:-40°C ~ 85°C 封装/外壳:8-SOIC（0.154"，3.90mm 宽） 供应商设备封装:8-TSOP 包装:管件 |
| XC18V512VQG44C | 功能描述:IC PROM REPROGR 512KB 44-VQFP RoHS:是 类别:集成电路 (IC) >> 存储器 - 用于 FPGA 的配置 Proms 系列:- 产品变化通告:Product Discontinuation 28/Jul/2010 标准包装:98 系列:- 可编程类型:OTP 存储容量:300kb 电源电压:3 V ~ 3.6 V 工作温度:-40°C ~ 85°C 封装/外壳:8-SOIC（0.154"，3.90mm 宽） 供应商设备封装:8-TSOP 包装:管件 |
| XC1900A-03 | 制造商:ANAREN 制造商全称:Anaren Microwave 功能描述:Hybrid Coupler 3 dB, 90∑ |
| XC1900A-03 SR | 制造商:Anaren Inc 功能描述:RF HYBRID COUPLER |
发布紧急采购，3分钟左右您将得到回复。