参数资料
| 型号： | XC3S1500-4FGG676I |
| 厂商： | Xilinx Inc |
| 文件页数： | 21/272页 |
| 文件大小： | 0K |
| 描述： | SPARTAN-3A FPGA 1.5M STD 676FBGA |
| 产品培训模块： | Extended Spartan 3A FPGA Family |
| 标准包装： | 40 |
| 系列： | Spartan®-3 |
| LAB/CLB数： | 3328 |
| 逻辑元件/单元数： | 29952 |
| RAM 位总计： | 589824 |
| 输入/输出数： | 487 |
| 门数： | 1500000 |
| 电源电压： | 1.14 V ~ 1.26 V |
| 安装类型： | 表面贴装 |
| 工作温度： | -40°C ~ 100°C |
| 封装/外壳： | 676-BGA |
| 供应商设备封装： | 676-FBGA（27x27） |
| 配用： | NANO-SPARTAN-ND - KIT NANOBOARD AND SPARTAN3 DC 807-1001-ND - DAUGHTER CARD XILINX SPARTAN 3 |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页当前第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页第44页第45页第46页第47页第48页第49页第50页第51页第52页第53页第54页第55页第56页第57页第58页第59页第60页第61页第62页第63页第64页第65页第66页第67页第68页第69页第70页第71页第72页第73页第74页第75页第76页第77页第78页第79页第80页第81页第82页第83页第84页第85页第86页第87页第88页第89页第90页第91页第92页第93页第94页第95页第96页第97页第98页第99页第100页第101页第102页第103页第104页第105页第106页第107页第108页第109页第110页第111页第112页第113页第114页第115页第116页第117页第118页第119页第120页第121页第122页第123页第124页第125页第126页第127页第128页第129页第130页第131页第132页第133页第134页第135页第136页第137页第138页第139页第140页第141页第142页第143页第144页第145页第146页第147页第148页第149页第150页第151页第152页第153页第154页第155页第156页第157页第158页第159页第160页第161页第162页第163页第164页第165页第166页第167页第168页第169页第170页第171页第172页第173页第174页第175页第176页第177页第178页第179页第180页第181页第182页第183页第184页第185页第186页第187页第188页第189页第190页第191页第192页第193页第194页第195页第196页第197页第198页第199页第200页第201页第202页第203页第204页第205页第206页第207页第208页第209页第210页第211页第212页第213页第214页第215页第216页第217页第218页第219页第220页第221页第222页第223页第224页第225页第226页第227页第228页第229页第230页第231页第232页第233页第234页第235页第236页第237页第238页第239页第240页第241页第242页第243页第244页第245页第246页第247页第248页第249页第250页第251页第252页第253页第254页第255页第256页第257页第258页第259页第260页第261页第262页第263页第264页第265页第266页第267页第268页第269页第270页第271页第272页
Spartan-3 FPGA Family: Pinout Descriptions
DS099 (v3.1) June 27, 2013
Product Specification
117
CCLK: Configuration Clock
The configuration clock signal on this pin synchronizes the reading or writing of configuration data. The CCLK pin is an
input-only pin for the Slave Serial and Slave Parallel configuration modes. In the Master Serial and Master Parallel
configuration modes, the FPGA drives the CCLK pin and CCLK should be treated as a full bidirectional I/O pin for signal
integrity analysis.
Although the CCLK frequency is relatively low, Spartan-3 FPGA output edge rates are fast. Any potential signal integrity
problems on the CCLK board trace can cause FPGA configuration to fail. Therefore, pay careful attention to the CCLK signal
integrity on the printed circuit board. Signal integrity simulation with IBIS is recommended. For all configuration modes
except JTAG, consider the signal integrity at every CCLK trace destination, including the FPGA’s CCLK pin. For more details
on CCLK design considerations, see Chapter 2 of UG332, Spartan-3 Generation Configuration User Guide.
During configuration, the CCLK pin has a pull-up resistor to VCCAUX, regardless of the HSWAP_EN pin. After configuration,
the CCLK pin is pulled High to VCCAUX by default as defined by the CclkPin bitstream selection, although this behavior is
programmable. Any clocks applied to CCLK after configuration are ignored unless the bitstream option Persist is set to Yes,
which retains the configuration interface. Persist is set to No by default. However, if Persist is set to Yes, then all clock
edges are potentially active events, depending on the other configuration control signals.
The bitstream generator option ConfigRate determines the frequency of the internally-generated CCLK oscillator required
for the Master configuration modes. The actual frequency is approximate due to the characteristics of the silicon oscillator
and varies by up to 50% over the temperature and voltage range. By default, CCLK operates at approximately 6 MHz. Via
the ConfigRate option, the oscillator frequency is set at approximately 3, 6, 12, 25, or 50 MHz. At power-on, CCLK always
starts operation at its lowest frequency. The device does not start operating at the higher frequency until the ConfigRate
control bits are loaded during the configuration process.
PROG_B: Program/Configure Device
This asynchronous pin initiates the configuration or re-configuration processes. A Low-going pulse resets the configuration
logic, initializing the configuration memory. This initialization process cannot finish until PROG_B returns High. Asserting
PROG_B Low for an extended period delays the configuration process. At power-up, there is always a pull-up resistor to
VCCAUX on this pin, regardless of the HSWAP_EN input. After configuration, the bitstream generator option ProgPin
determines whether or not the pull-up resistor is present. By default, the ProgPin option retains the pull-up resistor.
After configuration, hold the PROG_B input High. Any Low-going pulse on PROG_B lasting 300 ns or longer restarts the
configuration process.
DONE: Configuration Done, Delay Start-Up Sequence
The FPGA produces a Low-to-High transition on this pin indicating that the configuration process is complete. The bitstream
generator option DriveDone determines whether this pin functions as a totem-pole output that can drive High or as an
open-drain output. If configured as an open-drain output—which is the default behavior—then a pull-up resistor is required
to produce a High logic level. There is a bitstream option that provides an internal pull-up resistor, otherwise an external
pull-up resistor is required.
The open-drain option permits the DONE lines of multiple FPGAs to be tied together, so that the common node transitions
High only after all of the FPGAs have completed configuration. Externally holding the open-drain DONE pin Low delays the
start-up sequence, which marks the transition to user mode.
Table 73: PROG_B Operation
PROG_B Input
Response
Power-up
Automatically initiates configuration process.
Low-going pulse
Initiate (re-)configuration process and continue to completion.
Extended Low
Initiate (re-)configuration process and stall process at step where configuration memory is cleared. Process is
stalled until PROG_B returns High.
1
If the configuration process is started, continue to completion. If configuration process is complete, stay in User
mode.
相关PDF资料 |
PDF描述 |
|---|---|
| XC3S1500-5FGG676C | SPARTAN-3A FPGA 1.5M 676-FBGA |
| 25AA640XT-I/ST | IC EEPROM 64KBIT 1MHZ 8TSSOP |
| 24LC128-E/P | IC EEPROM 128KBIT 400KHZ 8DIP |
| XC2V250-4FG256I | IC FPGA VIRTEX-II 256FGBGA |
| 25LC320/P | IC EEPROM 32KBIT 2MHZ 8DIP |
相关代理商/技术参数 |
参数描述 |
|---|---|
| XC3S1500-4FT256C | 制造商:XILINX 制造商全称:XILINX 功能描述:Spartan-3 FPGA |
| XC3S1500-4FT256I | 制造商:XILINX 制造商全称:XILINX 功能描述:Spartan-3 FPGA |
| XC3S1500-4PQ208C | 制造商:XILINX 制造商全称:XILINX 功能描述:Spartan-3 FPGA |
| XC3S1500-4PQ208I | 制造商:XILINX 制造商全称:XILINX 功能描述:Spartan-3 FPGA |
| XC3S1500-4PQG208C | 制造商:XILINX 制造商全称:XILINX 功能描述:Spartan-3 FPGA Family: Complete Data Sheet |
发布紧急采购，3分钟左右您将得到回复。