参数资料
| 型号： | XC4020E-2HQ240I |
| 厂商： | Xilinx Inc |
| 文件页数： | 46/68页 |
| 文件大小： | 0K |
| 描述： | IC FPGA I-TEMP 5V 2SPD 240-HQFP |
| 产品变化通告： | XC1700 PROMs,XC5200,HQ,SCD Parts Discontinuation 19/Jul/2010 |
| 标准包装： | 1 |
| 系列： | XC4000E/X |
| LAB/CLB数： | 784 |
| 逻辑元件/单元数： | 1862 |
| RAM 位总计： | 25088 |
| 输入/输出数： | 193 |
| 门数： | 20000 |
| 电源电压： | 4.5 V ~ 5.5 V |
| 安装类型： | 表面贴装 |
| 工作温度： | -40°C ~ 100°C |
| 封装/外壳： | 240-BFQFP 裸露焊盘 |
| 供应商设备封装： | 240-PQFP（32x32） |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页第44页第45页当前第46页第47页第48页第49页第50页第51页第52页第53页第54页第55页第56页第57页第58页第59页第60页第61页第62页第63页第64页第65页第66页第67页第68页
R
XC4000E and XC4000X Series Field Programmable Gate Arrays
6-54
May 14, 1999 (Version 1.6)
Start-up from a User Clock (STARTUP.CLK)
When, instead of CCLK, a user-supplied start-up clock is
selected, Q1 is used to bridge the unknown phase relation-
ship between CCLK and the user clock. This arbitration
causes an unavoidable one-cycle uncertainty in the timing
of the rest of the start-up sequence.
DONE Goes High to Signal End of Conguration
XC4000 Series devices read the expected length count
from the bitstream and store it in an internal register. The
length count varies according to the number of devices and
the composition of the daisy chain. Each device also counts
the number of CCLKs during conguration.
Two conditions have to be met in order for the DONE pin to
go high:
the chip's internal memory must be full, and
the conguration length count must be met,
exactly.
This is important because the counter that determines
when the length count is met begins with the very rst
CCLK, not the rst one after the preamble.
Therefore, if a stray bit is inserted before the preamble, or
the data source is not ready at the time of the rst CCLK,
the internal counter that holds the number of CCLKs will be
one ahead of the actual number of data bits read. At the
end of conguration, the conguration memory will be full,
but the number of bits in the internal counter will not match
the expected length count.
As a consequence, a Master mode device will continue to
send out CCLKs until the internal counter turns over to
zero, and then reaches the correct length count a second
time. This will take several seconds [224
CCLK period] —
which is sometimes interpreted as the device not congur-
ing at all.
If it is not possible to have the data ready at the time of the
rst CCLK, the problem can be avoided by increasing the
number in the length count by the appropriate value. The
XACT User Guide includes detailed information about man-
ually altering the length count.
Note that DONE is an open-drain output and does not go
High unless an internal pull-up is activated or an external
pull-up is attached. The internal pull-up is activated as the
default by the bitstream generation software.
Release of User I/O After DONE Goes High
By default, the user I/O are released one CCLK cycle after
the DONE pin goes High. If CCLK is not clocked after
DONE goes High, the outputs remain in their initial state —
3-stated, with a 50 k
- 100 k pull-up. The delay from
DONE High to active user I/O is controlled by an option to
the bitstream generation software.
Release of Global Set/Reset After DONE Goes
High
By default, Global Set/Reset (GSR) is released two CCLK
cycles after the DONE pin goes High. If CCLK is not
clocked twice after DONE goes High, all ip-ops are held
in their initial set or reset state. The delay from DONE High
to GSR inactive is controlled by an option to the bitstream
generation software.
Conguration Complete After DONE Goes High
Three full CCLK cycles are required after the DONE pin
goes High, as shown in Figure 47 on page 53. If CCLK is
not clocked three times after DONE goes High, readback
cannot be initiated and most boundary scan instructions
cannot be used.
Conguration Through the Boundary Scan
Pins
XC4000 Series devices can be congured through the
boundary scan pins. The basic procedure is as follows:
Power up the FPGA with INIT held Low (or drive the
PROGRAM pin Low for more than 300 ns followed by a
High while holding INIT Low). Holding INIT Low allows
enough time to issue the CONFIG command to the
FPGA. The pin can be used as I/O after conguration if
a resistor is used to hold INIT Low.
Issue the CONFIG command to the TMS input
Wait for INIT to go High
Sequence the boundary scan Test Access Port to the
SHIFT-DR state
Toggle TCK to clock data into TDI pin.
The user must account for all TCK clock cycles after INIT
goes High, as all of these cycles affect the Length Count
compare.
For more detailed information, refer to the Xilinx application
note XAPP017, “
Boundary Scan in XC4000 Devices.” This
application note also applies to XC4000E and XC4000X
devices.
Product Obsolete or Under Obsolescence
相关PDF资料 |
PDF描述 |
|---|---|
| XC4020E-2HQ208I | IC FPGA I-TEMP 5V 2SPD 208-HQFP |
| RMC65DRAN-S734 | CONN EDGECARD 130PS .100 R/A PCB |
| IDT7130LA55PF8 | IC SRAM 8KBIT 55NS 64TQFP |
| IDT7130LA100PF8 | IC SRAM 8KBIT 100NS 64TQFP |
| IDT71V35761SA200BQGI8 | IC SRAM 4MBIT 200MHZ 165FBGA |
相关代理商/技术参数 |
参数描述 |
|---|---|
| XC4020E-2PG223C | 功能描述:IC FPGA C-TEMP 5V 2SPD 223-CPGA RoHS:否 类别:集成电路 (IC) >> 嵌入式 - FPGA（现场可编程门阵列） 系列:XC4000E/X 标准包装:1 系列:Kintex-7 LAB/CLB数:25475 逻辑元件/单元数:326080 RAM 位总计:16404480 输入/输出数:350 门数:- 电源电压:0.97 V ~ 1.03 V 安装类型:表面贴装 工作温度:0°C ~ 85°C 封装/外壳:900-BBGA，FCBGA 供应商设备封装:900-FCBGA（31x31） 其它名称:122-1789 |
| XC4020E-2PG223I | 功能描述:IC FPGA I-TEMP 5V 2SPD 223-CPGA RoHS:否 类别:集成电路 (IC) >> 嵌入式 - FPGA（现场可编程门阵列） 系列:XC4000E/X 标准包装:1 系列:Kintex-7 LAB/CLB数:25475 逻辑元件/单元数:326080 RAM 位总计:16404480 输入/输出数:350 门数:- 电源电压:0.97 V ~ 1.03 V 安装类型:表面贴装 工作温度:0°C ~ 85°C 封装/外壳:900-BBGA，FCBGA 供应商设备封装:900-FCBGA（31x31） 其它名称:122-1789 |
| XC4020E3HQ2081 | 制造商:XILINX 功能描述:* |
| XC4020E-3HQ208C | 功能描述:IC FPGA 784 CLB'S 208-HQFP RoHS:否 类别:集成电路 (IC) >> 嵌入式 - FPGA（现场可编程门阵列） 系列:XC4000E/X 产品变化通告:XC4000(E,L) Discontinuation 01/April/2002 标准包装:24 系列:XC4000E/X LAB/CLB数:100 逻辑元件/单元数:238 RAM 位总计:3200 输入/输出数:80 门数:3000 电源电压:4.5 V ~ 5.5 V 安装类型:表面贴装 工作温度:-40°C ~ 100°C 封装/外壳:120-BCBGA 供应商设备封装:120-CPGA（34.55x34.55） |
| XC4020E-3HQ208I | 功能描述:IC FPGA I-TEMP 5V 3SPD 208-HQFP RoHS:否 类别:集成电路 (IC) >> 嵌入式 - FPGA（现场可编程门阵列） 系列:XC4000E/X 标准包装:1 系列:Kintex-7 LAB/CLB数:25475 逻辑元件/单元数:326080 RAM 位总计:16404480 输入/输出数:350 门数:- 电源电压:0.97 V ~ 1.03 V 安装类型:表面贴装 工作温度:0°C ~ 85°C 封装/外壳:900-BBGA，FCBGA 供应商设备封装:900-FCBGA（31x31） 其它名称:122-1789 |
发布紧急采购，3分钟左右您将得到回复。