- 您现在的位置：买卖IC网 > PDF目录11542 > XCCACE-TQ144I (Xilinx Inc)IC ACE CONTROLLER CHIP PDF资料下载
参数资料
| 型号： | XCCACE-TQ144I |
| 厂商： | Xilinx Inc |
| 文件页数： | 3/69页 |
| 文件大小： | 0K |
| 描述： | IC ACE CONTROLLER CHIP |
| 产品变化通告： | XCCACE-TQ144I Discontinuation 27/Feb/2006 |
| 标准包装： | 1 |
| 控制器类型： | ACE 控制器 |
| 电源电压： | 3 V ~ 3.6 V |
| 电流 - 电源： | 30mA |
| 工作温度： | -40°C ~ 85°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 144-LQFP |
| 供应商设备封装： | 144-TQFP（20x20） |
| 包装： | 托盘 |
第1页第2页当前第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页第44页第45页第46页第47页第48页第49页第50页第51页第52页第53页第54页第55页第56页第57页第58页第59页第60页第61页第62页第63页第64页第65页第66页第67页第68页第69页
System ACE CompactFlash Solution
DS080 (v3.0) April 7, 2014
Product Specification
R
— OBSOLETE — OBSOLETE — OBSOLETE — OBSOLETE —
Controlling the Number of Reserved Sectors
Windows 2000, Windows NT, and Windows 98 default to
one reserved sector when formatting. Therefore, formatting
the CF card using these Windows operating systems is not
problematical in this regard.
In Windows XP, however, the DOS format command auto-
matically formats the CF card with from two to eight
reserved sectors, depending on the density of the CF card.
Because the DOS format command does not allow specifi-
cation of the number of reserved sectors, an alternate disk
formatting
utility
(such
as
mkdosfs,
available
from
http://www1.mager.org/mkdosfs) must be used. When
the CF card is correctly formatted, Windows XP can be
used to perform normal file access (read/write) operations
without causing any additional problems.
Microprocessor Interface (MPU)
The MPU Interface provides a useful means of monitoring
the status of and controlling the System ACE CF controller,
as well as CompactFlash card READ / WRITE data. The
MPU is not required for normal operation, but when used, it
provides numerous capabilities. This interface enables
communication between an MPU device and a Compact-
Flash module and the FPGA target system.
The MPU interface is composed of a set of registers that
provide a means for communicating with CompactFlash
control
logic,
configuration
control
logic,
and
other
resources in the System ACE CF controller. Specifically, this
interface can be used to read the identity of a Compact-
Flash device and read/write sectors from or to a Compact-
Flash device.
The MPU interface can also be used to control configuration
flow. The MPU interface enables monitoring of System ACE
CF controller configuration status and error conditions. The
MPU interface can be used to delay configuration, start con-
figuration, determine the source of configuration (Compact-
Flash or MPU), control the bitstream version, reset the
device, etc.
Two important issues should be understood when using the
microprocessor port:
For the System ACE CF controller to be properly
synchronized, the device driving the MPU interface
must be synchronized to the CLK signal
The MPU must comply with System ACE timing
requirements
This general-purpose microprocessor interface can update
the CompactFlash, read the ACE status, or obtain direct
access to the JTAG configuration ports using the ACE
Microprocessor commands. This interface supports either
8-bit (default) or 16-bit data transfers. The bus width can be
configured dynamically.
All communications between the System ACE CF controller
and a host microprocessor involve transfer of data to or from
ACE registers. There are 128 addressable registers in 8-bit
mode and 64 addressable registers in 16-bit mode. For
easy selection of a new configuration from CompactFlash
data, the MPU interface allows for easy reconfiguration of
an FPGA chain or capability.
When using the MPU interface as the configuration source,
the CFGTCK output for the System ACE CF controller
device is derived from the CLK input to the System ACE CF
controller (supplied by the MPU), and the operating fre-
quency of the CFGTCK is the same as CLK.
The minimum clock operating frequency is 0 MHz.
The maximum clock operating frequency is either 33
MHz or the maximum JTAG TCK clock speed dictated
by the devices in the JTAG chain and/or the board
design. The lowest of these values should be used.
The following sections describe supported operations when
using the MPU interface.
MPU Port Signal Description
MPU interface port signals are described in Table 6.
Table 6: MPU Interface Port Signal Description
Name
Width
Direction
Active
Description
MPA
7
In
N/A
Synchronous address inputs. The internal address register is loaded by MPA
by a combination of the rising edge of CLK and MPCE LOW.
MPD
16
In/Out
N/A
Synchronous data input/output pins. Both the data input and output path are
registered and triggered by the rising edge of CLK.
MPCE
1In
LOW
Synchronous active LOW chip enable. MPCE LOW is used to enable the
MPU interface. MPCE LOW is also used in conjunction with MPOE LOW to
enable the MPD output.
相关PDF资料 |
PDF描述 |
|---|---|
| VI-21W-IY-B1 | CONVERTER MOD DC/DC 5.5V 50W |
| VE-21X-IY-B1 | CONVERTER MOD DC/DC 5.2V 50W |
| VI-B1X-IY-B1 | CONVERTER MOD DC/DC 5.2V 50W |
| V72A24C400B3 | CONVERTER MOD DC/DC 24V 400W |
| V72A15C400BL2 | CONVERTER MOD DC/DC 15V 400W |
相关代理商/技术参数 |
参数描述 |
|---|---|
| XCCACE-TQG144I | 功能描述:IC ACE CONTROLLER CHIP TQ144 RoHS:是 类别:集成电路 (IC) >> 接口 - 控制器 系列:- 标准包装:4,900 系列:- 控制器类型:USB 2.0 控制器 接口:串行 电源电压:3 V ~ 3.6 V 电流 - 电源:135mA 工作温度:0°C ~ 70°C 安装类型:表面贴装 封装/外壳:36-VFQFN 裸露焊盘 供应商设备封装:36-QFN（6x6） 包装:* 其它名称:Q6396337A |
| XCCAE7C13N | 制造商:Schneider Electric 功能描述:ABSOLUTE ENCDER SINGLE TURN 13 BITS 11 30V DC 制造商:SCHNEIDER ELECTRIC 功能描述:ABSOLUTE ENCDER SINGLE TURN |
| XCC-C0 | 制造商:Excelsys Technologies 功能描述:ELECTRONIC PART |
| XCCN0000 | 制造商:Red Lion Controls 功能描述:OPTION CARD, DSP/MC CANOPEN OPTION CARD 制造商:Red Lion Controls 功能描述:DSP/MC CANOPEN OPTION CARD |
| XCCPM23121L10 | 制造商:Schneider Electric 功能描述:pre-wired M23 female connector - for incremental encoder - cable 10m 制造商:Schneider Electric 功能描述:Cable Assembly Pre-Wired Pigtail 10m 10 POS M23 Circular F |
发布紧急采购，3分钟左右您将得到回复。