- 您现在的位置：买卖IC网 > PDF目录300157 > XCS30XL-4TQ280I (Xilinx, Inc.) Spartan and Spartan-XL Families Field Programmable Gate Arrays PDF资料下载
参数资料
| 型号： | XCS30XL-4TQ280I |
| 厂商： | Xilinx, Inc. |
| 英文描述： | Spartan and Spartan-XL Families Field Programmable Gate Arrays |
| 中文描述： | 斯巴达和Spartan - xL的家庭现场可编程门阵列 |
| 文件页数： | 29/82页 |
| 文件大小： | 863K |
| 代理商： | XCS30XL-4TQ280I |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页当前第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页第44页第45页第46页第47页第48页第49页第50页第51页第52页第53页第54页第55页第56页第57页第58页第59页第60页第61页第62页第63页第64页第65页第66页第67页第68页第69页第70页第71页第72页第73页第74页第75页第76页第77页第78页第79页第80页第81页第82页
Spartan and Spartan-XL Families Field Programmable Gate Arrays
DS060 (v1.6) September 19, 2001
Product Specification
1-800-255-7778
R
Configuration
The 0010 preamble code indicates that the following 24 bits
represent the length count for serial modes. The length
count is the total number of configuration clocks needed to
load the complete configuration data. (Four additional con-
figuration clocks are required to complete the configuration
process, as discussed below.) After the preamble and the
length count have been passed through to any device in the
daisy chain, its DOUT is held High to prevent frame start
bits from reaching any daisy-chained devices. In Spar-
tan-XL Express mode, the length count bits are ignored,
and DOUT is held Low, to disable the next device in the
pseudo daisy chain.
A specific configuration bit, early in the first frame of a mas-
ter device, controls the configuration-clock rate and can
increase it by a factor of eight. Therefore, if a fast configura-
tion clock is selected by the bitstream, the slower clock rate
is used until this configuration bit is detected.
Each frame has a start field followed by the frame-configu-
ration data bits and a frame error field. If a frame data error
is detected, the FPGA halts loading, and signals the error by
pulling the open-drain INIT pin Low. After all configuration
frames have been loaded into an FPGA using a serial
mode, DOUT again follows the input data so that the
remaining data is passed on to the next device. In
Spartan-XL Express mode, when the first device is fully pro-
grammed, DOUT goes High to enable the next device in the
chain.
Delaying Configuration After Power-Up
There are two methods of delaying configuration after
power-up: put a logic Low on the PROGRAM input, or pull
the bidirectional INIT pin Low, using an open-collector
(open-drain) driver. (See Figure 30.)
A Low on the PROGRAM input is the more radical
approach, and is recommended when the power-supply rise
time is excessive or poorly defined. As long as PROGRAM
is Low, the FPGA keeps clearing its configuration memory.
When PROGRAM goes High, the configuration memory is
cleared one more time, followed by the beginning of config-
uration, provided the INIT input is not externally held Low.
Note that a Low on the PROGRAM input automatically
forces a Low on the INIT output. The Spartan/XL PRO-
GRAM pin has a permanent weak pull-up. Avoid holding
PROGRAM Low for more than 500
s.
Using an open-collector or open-drain driver to hold INIT
Low before the beginning of configuration causes the FPGA
to wait after completing the configuration memory clear
operation. When INIT is no longer held Low externally, the
device determines its configuration mode by capturing the
state of the Mode pins, and is ready to start the configura-
tion process. A master device waits up to an additional
300
s to make sure that any slaves in the optional daisy
chain have seen that INIT is High.
Figure 30: Power-up Configuration Sequence
INIT
High? if
Master
Sample
Mode Line
Load One
Configuration
Data Frame
Frame
Error
Pass
Configuration
Data to DOUT
VCC
Valid
No
Yes
No
Yes
Operational
Start-Up
Sequence
No
Yes
~1.3
s per Frame
Master Delays Before
Sampling Mode Line
Master CCLK
Goes Active
F
Pull INIT Low
and Stop
DS060_30_080400
EXTEST*
SAMPLE/PRELOAD
BYPASS
CONFIGURE*
(* if PROGRAM = High)
SAMPLE/PRELOAD
BYPASS
EXTEST
SAMPLE PRELOAD
BYPASS
USER 1
USER 2
CONFIGURE
READBACK
If Boundary Scan
is Selected
Config-
uration
memory
Full
CCLK
Count Equals
Length
Count
Completely Clear
Configuration Memory
Once More
LDC
Output
=
L,
HDC
Output
=
H
Boundary Scan
Instructions
Available:
I/O
Active
Keep Clearing
Configuration
Memory
Test MODE, Generate
One Time-Out Pulse
of 16 or 64 ms
PROGRAM
= Low
No
Yes
相关PDF资料 |
PDF描述 |
|---|---|
| XCS30XL-4TQ84C | Spartan and Spartan-XL Families Field Programmable Gate Arrays |
| XCS30XL-4TQ84I | Spartan and Spartan-XL Families Field Programmable Gate Arrays |
| XCS30XL-4VQ144C | Spartan and Spartan-XL Families Field Programmable Gate Arrays |
| XCS30XL-4VQ208C | Spartan and Spartan-XL Families Field Programmable Gate Arrays |
| XCS30XL-4VQ208I | Spartan and Spartan-XL Families Field Programmable Gate Arrays |
相关代理商/技术参数 |
参数描述 |
|---|---|
| XCS30XL-4TQ84C | 制造商:XILINX 制造商全称:XILINX 功能描述:Spartan and Spartan-XL Families Field Programmable Gate Arrays |
| XCS30XL-4TQ84I | 制造商:XILINX 制造商全称:XILINX 功能描述:Spartan and Spartan-XL Families Field Programmable Gate Arrays |
| XCS30XL-4TQG144C | 功能描述:IC SPARTAN-XL FPGA 30K 144-TQFP RoHS:是 类别:集成电路 (IC) >> 嵌入式 - FPGA（现场可编程门阵列） 系列:Spartan®-XL 标准包装:1 系列:Kintex-7 LAB/CLB数:25475 逻辑元件/单元数:326080 RAM 位总计:16404480 输入/输出数:350 门数:- 电源电压:0.97 V ~ 1.03 V 安装类型:表面贴装 工作温度:0°C ~ 85°C 封装/外壳:900-BBGA，FCBGA 供应商设备封装:900-FCBGA（31x31） 其它名称:122-1789 |
| XCS30XL-4TQG144I | 功能描述:IC SPARTAN-XL FPGA 30K 144-TQFP RoHS:是 类别:集成电路 (IC) >> 嵌入式 - FPGA（现场可编程门阵列） 系列:Spartan®-XL 标准包装:1 系列:Kintex-7 LAB/CLB数:25475 逻辑元件/单元数:326080 RAM 位总计:16404480 输入/输出数:350 门数:- 电源电压:0.97 V ~ 1.03 V 安装类型:表面贴装 工作温度:0°C ~ 85°C 封装/外壳:900-BBGA，FCBGA 供应商设备封装:900-FCBGA（31x31） 其它名称:122-1789 |
| XCS30XL-4VQ100C | 功能描述:IC FPGA 3.3V C-TEMP HP 100VQFP RoHS:否 类别:集成电路 (IC) >> 嵌入式 - FPGA（现场可编程门阵列） 系列:Spartan®-XL 标准包装:1 系列:Kintex-7 LAB/CLB数:25475 逻辑元件/单元数:326080 RAM 位总计:16404480 输入/输出数:350 门数:- 电源电压:0.97 V ~ 1.03 V 安装类型:表面贴装 工作温度:0°C ~ 85°C 封装/外壳:900-BBGA，FCBGA 供应商设备封装:900-FCBGA（31x31） 其它名称:122-1789 |
发布紧急采购，3分钟左右您将得到回复。