参数资料
| 型号： | XCV405E-7BG560I |
| 厂商： | Xilinx Inc |
| 文件页数： | 54/118页 |
| 文件大小： | 0K |
| 描述： | IC FPGA 1.8V 560-MBGA |
| 产品变化通告： | FPGA Family Discontinuation 18/Apr/2011 |
| 标准包装： | 1 |
| 系列： | Virtex®-E EM |
| LAB/CLB数： | 2400 |
| 逻辑元件/单元数： | 10800 |
| RAM 位总计： | 573440 |
| 输入/输出数： | 404 |
| 门数： | 129600 |
| 电源电压： | 1.71 V ~ 1.89 V |
| 安装类型： | 表面贴装 |
| 工作温度： | -40°C ~ 100°C |
| 封装/外壳： | 560-LBGA，金属 |
| 供应商设备封装： | 560-MBGA（42.5x42.5） |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页第44页第45页第46页第47页第48页第49页第50页第51页第52页第53页当前第54页第55页第56页第57页第58页第59页第60页第61页第62页第63页第64页第65页第66页第67页第68页第69页第70页第71页第72页第73页第74页第75页第76页第77页第78页第79页第80页第81页第82页第83页第84页第85页第86页第87页第88页第89页第90页第91页第92页第93页第94页第95页第96页第97页第98页第99页第100页第101页第102页第103页第104页第105页第106页第107页第108页第109页第110页第111页第112页第113页第114页第115页第116页第117页第118页
Virtex-E 1.8 V Extended Memory Field Programmable Gate Arrays
Module 2 of 4
DS025-2 (v3.0) March 21, 2014
36
R
— OBSOLETE — OBSOLETE — OBSOLETE — OBSOLETE —
The LVTTL OBUFT additionally can support one of two slew
rate modes to minimize bus transients. By default, the slew
rate for each output buffer is reduced to minimize power bus
transients when switching non-critical signals.
LVTTL
3-state
output
buffers
have
selectable
drive
strengths.
The format for LVTTL OBUFT symbol names is as follows.
OBUFT_<slew_rate>_<drive_strength>
<slew_rate> can be either F (Fast), or S (Slow) and
<drive_strength> is specified in milliamps (2, 4, 6, 8, 12, 16,
or 24).
The following list details variations of the OBUFT symbol.
OBUFT
OBUFT_S_2
OBUFT_S_4
OBUFT_S_6
OBUFT_S_8
OBUFT_S_12
OBUFT_S_16
OBUFT_S_24
OBUFT_F_2
OBUFT_F_4
OBUFT_F_6
OBUFT_F_8
OBUFT_F_12
OBUFT_F_16
OBUFT_F_24
OBUFT_LVCMOS2
OBUFT_PCI33_3
OBUFT_PCI66_3
OBUFT_GTL
OBUFT_GTLP
OBUFT_HSTL_I
OBUFT_HSTL_III
OBUFT_HSTL_IV
OBUFT_SSTL3_I
OBUFT_SSTL3_II
OBUFT_SSTL2_I
OBUFT_SSTL2_II
OBUFT_CTT
OBUFT_AGP
OBUFT_LVCMOS18
OBUFT_LVDS
OBUFT_LVPECL
The Virtex-E series supports eight banks for the HQ and PQ
packages. The CS package supports four VCCO banks.
The SelectI/O OBUFT placement restrictions require that
within a given VCCO bank each OBUFT share the same out-
put source drive voltage. Input buffers of any type and out-
put buffers that do not require VCCO can be placed within
the same VCCO bank.
The LOC property can specify a location for the OBUFT.
3-state output buffers and bidirectional buffers can have
either a weak pull-up resistor, a weak pull-down resistor, or
a weak “keeper” circuit. Control this feature by adding the
appropriate symbol to the output net of the OBUFT (PUL-
LUP, PULLDOWN, or KEEPER).
The weak “keeper” circuit requires the input buffer within the
IOB to sample the I/O signal. So, OBUFTs programmed for
an I/O standard that requires a VREF have automatic place-
ment of a VREF in the bank with an OBUFT configured with
a weak “keeper” circuit. This restriction does not affect most
circuit design as applications using an OBUFT configured
with a weak “keeper” typically implement a bidirectional I/O.
In this case the IBUF (and the corresponding VREF) are
explicitly placed.
The LOC property can specify a location for the OBUFT.
IOBUF
Use the IOBUF symbol for bidirectional signals that require
both an input buffer and a 3-state output buffer with an
active high 3-state pin. The generic input/output buffer
IOBUF appears in Figure 42.
The extension to the base name defines which I/O standard
the IOBUF uses. With no extension specified for the generic
IOBUF symbol, the assumed standard is LVTTL input buffer
and slew rate limited LVTTL with 12 mA drive strength for
the output buffer.
The LVTTL IOBUF additionally can support one of two slew
rate modes to minimize bus transients. By default, the slew
rate for each output buffer is reduced to minimize power bus
transients when switching non-critical signals.
LVTTL bidirectional buffers have selectable output drive
strengths.
The format for LVTTL IOBUF symbol names is as follows.
IOBUF_<slew_rate>_<drive_strength>
<slew_rate> can be either F (Fast), or S (Slow) and
<drive_strength> is specified in milliamps (2, 4, 6, 8, 12, 16,
or 24).
Figure 41: 3-State Output Buffer Symbol (OBUFT)
O
I
OBUFT
x133_05_111699
T
相关PDF资料 |
PDF描述 |
|---|---|
| XC4VLX80-10FF1148I | IC FPGA VIRTEX-4LX 1148FFBGA |
| XC4VLX80-11FFG1148C | IC FPGA VIRTEX-4 LX 80K 1148FBGA |
| XC4VLX80-10FFG1148I | IC FPGA VIRTEX-4 LX 80K 1148FBGA |
| XCV600E-8FG900C | IC FPGA 1.8V C-TEMP 900-FBGA |
| XCV600E-7FG900I | IC FPGA 1.8V I-TEMP 900-FBGA |
相关代理商/技术参数 |
参数描述 |
|---|---|
| XCV405E-7BG676C | 制造商:XILINX 制造商全称:XILINX 功能描述:Virtex-E 1.8 V Extended Memory Field Programmable Gate Arrays |
| XCV405E-7BG676I | 制造商:XILINX 制造商全称:XILINX 功能描述:Virtex-E 1.8 V Extended Memory Field Programmable Gate Arrays |
| XCV405E-7BG900C | 制造商:XILINX 制造商全称:XILINX 功能描述:Virtex-E 1.8 V Extended Memory Field Programmable Gate Arrays |
| XCV405E-7BG900I | 制造商:XILINX 制造商全称:XILINX 功能描述:Virtex-E 1.8 V Extended Memory Field Programmable Gate Arrays |
| XCV405E-7FG404C | 制造商:XILINX 制造商全称:XILINX 功能描述:Virtex-E 1.8 V Extended Memory Field Programmable Gate Arrays |
发布紧急采购，3分钟左右您将得到回复。