- 您现在的位置：买卖IC网 > Datasheet目录58 > XIB-E (Digi International/Maxstream)BOARD INTERFACE ETHERNET Datasheet资料下载
参数资料
| 型号： | XIB-E |
| 厂商： | Digi International/Maxstream |
| 文件页数： | 33/64页 |
| 文件大小： | 1858K |
| 描述： | BOARD INTERFACE ETHERNET |
| 标准包装： | 1 |
| 附件类型： | 接口板 |
| 适用于相关产品： | XStream 和 Xcite 收音机 |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页当前第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页第44页第45页第46页第47页第48页第49页第50页第51页第52页第53页第54页第55页第56页第57页第58页第59页第60页第61页第62页第63页第64页
XStream"燨EM燫F燤odule?燩roduct燤anual爒5.x00燵2006.02.24]?/DIV>
SY (Time before Initialization) Command
AT Command: ATSY
Binary Command: 0x17 (23 decimal)
<Networking & Security> SY Command keeps a
communication channel open as long as module
transmits or receives before the active connection
expires. It can be used to reduce latency in a
query/response sequence and should be set 100
ms longer than the delay between transmissions.
Parameter Range: 0 0xFF
This command allows multiple XStream Modules
to share a hopping channel for a given amount of time after receiving data. By default, all
packets include an RF initializer that contains channel information used to synchronize any
listening receivers to the transmitters hopping pattern. Once a new module comes within range,
it is able to instantly synchronize to the transmitter and start receiving data. If no new modules
are introduced into the system, the synchronization information becomes redundant once
modules have become synchronized.
[x 100 milliseconds]
Default Parameter Value: 0 (Disabled - channel
initialization info sent with each RF packet.)
Number of bytes returned: 1
SY Command allows the modules to remove this information from the RF Initializer after the
initial synchronization. For example, changing the SY Parameter to 0x14 (20 decimal) allows all
modules to remain in sync for 2 seconds after the last data packet was received. Synchronization
information is not re-sent unless transmission stops for more than 2 seconds. This command
allows significant savings in packet transmission time.
Warning: Not recommended for use in an interference-prone environment. Interference can break up
the session and the communications channel will not be available again until SY time expires.
With SY set to zero, the channel session is opened and closed with each transmission - resulting
in a more robust link with more latency.
TO (DO2 Timeout) Command
AT Command: ATTO
Binary Command: 0x31 (49 decimal)
Parameter Range: 0 0xFFFF [x 1 second]
Default Parameter Value: 3
Number of bytes returned: 2
Minimum Firmware Version Required: 4.30
<Serial Interfacing>DO2 output will return to
default after no DI2 status information is
received during the timeout period.
Use with CS = 2 or 4.
TR (Transmit Error Count) Command
AT Command: ATTR
Binary Command: 0x1B (27 decimal)
Parameter Range: 0 0xFFFF
Default Parameter Value: 0
Number of bytes returned: 2
Related Commands: RR (Retries)
Minimum Firmware Version Required: 4.22
<Diagnostics> Read number of retransmit
failures. The number of retransmit errors is
incremented each time a packet is not
acknowledged within the number of retransmits
specified by the RR (Retries) parameter. It
therefore counts the number of packets that were
not successfully received and have been dropped.
The TR parameter is not non-volatile and therefore is reset to zero each time the module is reset.
牋牘?006燤axStream,營nc.燙onfidential燼nd燩roprietary?/DIV>
33?/DIV>
相关PDF资料 |
PDF描述 |
|---|---|
| XIB-R | BOARD INTERFACE RS232/485 |
| ZMN2400HPDB | BOARD ROUTER DEV ZIGBEE 100MW |
| ZMN24HPDK-B | KIT DEV W/ZIGBEE ZMN2400HP |
| ZNI1000TC | IC TEMP SENSOR NI1000 SOT23-3 |
| 02110102-000 | SNSR TILT RATIO 60DEG 500MA FLNG |
相关代理商/技术参数 |
参数描述 |
|---|---|
| XIB-R | 功能描述:界面模块 RS-232/485 interface 24XStream 9XCite RoHS:否 制造商:4D Systems 产品:Serial Converters 通道/端口数量: 数据速率: 接口类型:USB, UART 工作电源电压:3.3 V, 5 V 最大工作温度: |
| XIB-U | 功能描述:界面模块 USB interface board 24XStream 9XCite RoHS:否 制造商:4D Systems 产品:Serial Converters 通道/端口数量: 数据速率: 接口类型:USB, UART 工作电源电压:3.3 V, 5 V 最大工作温度: |
| XIC25040 | 制造商:XIC 功能描述:25040 24HR '6 |
| XILINXPWR-079 | 功能描述:电源管理IC开发工具 Pow Mgt Eval Mod for Xilinx FPGAs RoHS:否 制造商:Maxim Integrated 产品:Evaluation Kits 类型:Battery Management 工具用于评估:MAX17710GB 输入电压: 输出电压:1.8 V |
| XILINXPWR-080 | 功能描述:电源管理IC开发工具 Pow Mgt Eval Mod for Xilinx FPGAs RoHS:否 制造商:Maxim Integrated 产品:Evaluation Kits 类型:Battery Management 工具用于评估:MAX17710GB 输入电压: 输出电压:1.8 V |
发布紧急采购，3分钟左右您将得到回复。