参数资料
| 型号： | XR16L784CV-F |
| 厂商： | Exar Corporation |
| 文件页数： | 29/51页 |
| 文件大小： | 0K |
| 描述： | IC UART 8B 3.3V QUAD 64LQFP |
| 标准包装： | 160 |
| 特点： | * |
| 通道数： | 4，QUART |
| FIFO's： | 64 字节 |
| 规程： | RS485 |
| 电源电压： | 2.97 V ~ 5.5 V |
| 带自动流量控制功能： | 是 |
| 带IrDA 编码器/解码器： | 是 |
| 带故障启动位检测功能： | 是 |
| 带调制解调器控制功能： | 是 |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 64-LQFP |
| 供应商设备封装： | 64-LQFP（10x10） |
| 包装： | 托盘 |
| 其它名称： | 1016-1281 |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页当前第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页第44页第45页第46页第47页第48页第49页第50页第51页
XR16L784
35
REV. 1.2.3
HIGH PERFORMANCE 2.97V TO 5.5V QUAD UART
MSR[0]: Delta CTS# Input Flag
Logic 0 = No change on CTS# input (default).
Logic 1 = The CTS# input has changed state since the last time it was monitored. A modem status interrupt
will be generated if MSR interrupt is enabled (IER bit-3.
MSR[1]: Delta DSR# Input Flag
Logic 0 = No change on DSR# input (default).
Logic 1 = The DSR# input has changed state since the last time it was monitored. A modem status interrupt
will be generated if MSR interrupt is enabled (IER bit-3.
MSR[2]: Delta RI# Input Flag
Logic 0 = No change on RI# input (default).
Logic 1 = The RI# input has changed from a logic 0 to a logic 1, ending of the ringing signal. A modem status
interrupt will be generated if MSR interrupt is enabled (IER bit-3.
MSR[3]: Delta CD# Input Flag
Logic 0 = No change on CD# input (default).
Logic 1 = Indicates that the CD# input has changed state since the last time it was monitored. A modem
status interrupt will be generated if MSR interrupt is enabled (IER bit-3.
MSR[4]: CTS Input Status
CTS# pin may function as automatic hardware flow control signal input if it is enabled and selected by Auto
CTS (EFR bit-7) and RTS/CTS flow control select (MCR bit-2). Auto CTS flow control allows starting and
stopping of local data transmissions based on the modem CTS# signal. A HIGH on the CTS# pin will stop
UART transmitter as soon as the current character has finished transmission, and a LOW will resume data
transmission. Normally MSR bit-4 bit is the complement of the CTS# input. However in the loopback mode, this
bit is equivalent to the RTS# bit in the MCR register. The CTS# input may be used as a general purpose input
when the modem interface is not used.
MSR[5]: DSR Input Status
This input may be used for auto DTR/DSR flow control function, see auto hardware flow control section.
Normally this bit is the complement of the DSR# input. In the loopback mode, this bit is equivalent to the DTR#
bit in the MCR register. The DSR# input may be used as a general purpose input when the modem interface is
not used.
MSR[6]: RI Input Status
Normally this bit is the complement of the RI# input. In the loopback mode this bit is equivalent to bit-2 in the
MCR register. The RI# input may be used as a general purpose input when the modem interface is not used.
MSR[7]: CD Input Status
Normally this bit is the complement of the CD# input. In the loopback mode this bit is equivalent to bit-3 in the
MCR register. The CD# input may be used as a general purpose input when the modem interface is not used.
4.10
Modem Status Register (MSR) - Write Only
The upper four bits 4-7 of this register sets the delay in number of bits time for the auto RS485 turn around
from transmit to receive.
MSR [7:4]
When Auto RS485 feature is enabled (FCTR bit-5=1) and RTS# output is connected to the enable input of a
RS-485 transceiver. These 4 bits select from 0 to 15 bit-time delay after the end of the last stop-bit of the last
transmitted character. This delay controls when to change the state of RTS# output. This delay is very useful in
long-cable networks. Table 16 shows the selection. The bits are enabled by EFR bit-4.
相关PDF资料 |
PDF描述 |
|---|---|
| XR16C854CV-F | IC UART FIFO 128B QUAD 64LQFP |
| ST16C654IQ64-F | IC UART FIFO 64B QUAD 64LQFP |
| XR16V654IV-F | IC UART FIFO 64B QUAD 64LQFP |
| ST16C654CQ64-F | IC UART FIFO 64B QUAD 64LQFP |
| ST16C654DCQ64-F | IC UART FIFO 64B QUAD 64LQFP |
相关代理商/技术参数 |
参数描述 |
|---|---|
| XR16L784CVTR-F | 功能描述:UART 接口集成电路 3.3V QUAD UART RoHS:否 制造商:Texas Instruments 通道数量:2 数据速率:3 Mbps 电源电压-最大:3.6 V 电源电压-最小:2.7 V 电源电流:20 mA 最大工作温度:+ 85 C 最小工作温度:- 40 C 封装 / 箱体:LQFP-48 封装:Reel |
| XR16L784IV | 制造商:EXAR 制造商全称:EXAR 功能描述:HIGH PERFORMANCE 2.97V TO 5.5V QUAD UART |
| XR16L784IV-F | 功能描述:UART 接口集成电路 2.97V-5.5V 64B FIFO temp -45 to 85C RoHS:否 制造商:Texas Instruments 通道数量:2 数据速率:3 Mbps 电源电压-最大:3.6 V 电源电压-最小:2.7 V 电源电流:20 mA 最大工作温度:+ 85 C 最小工作温度:- 40 C 封装 / 箱体:LQFP-48 封装:Reel |
| XR16L784IVTR-F | 功能描述:UART 接口集成电路 PCI BUS QUAD UART RoHS:否 制造商:Texas Instruments 通道数量:2 数据速率:3 Mbps 电源电压-最大:3.6 V 电源电压-最小:2.7 V 电源电流:20 mA 最大工作温度:+ 85 C 最小工作温度:- 40 C 封装 / 箱体:LQFP-48 封装:Reel |
| XR16L788 | 制造商:EXAR 制造商全称:EXAR 功能描述:HIGH PERFORMANCE OCTAL UART |
发布紧急采购，3分钟左右您将得到回复。