参数资料
| 型号： | XR16L784CV-F |
| 厂商： | Exar Corporation |
| 文件页数： | 33/51页 |
| 文件大小： | 0K |
| 描述： | IC UART 8B 3.3V QUAD 64LQFP |
| 标准包装： | 160 |
| 特点： | * |
| 通道数： | 4，QUART |
| FIFO's： | 64 字节 |
| 规程： | RS485 |
| 电源电压： | 2.97 V ~ 5.5 V |
| 带自动流量控制功能： | 是 |
| 带IrDA 编码器/解码器： | 是 |
| 带故障启动位检测功能： | 是 |
| 带调制解调器控制功能： | 是 |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 64-LQFP |
| 供应商设备封装： | 64-LQFP（10x10） |
| 包装： | 托盘 |
| 其它名称： | 1016-1281 |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页当前第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页第44页第45页第46页第47页第48页第49页第50页第51页
XR16L784
39
REV. 1.2.3
HIGH PERFORMANCE 2.97V TO 5.5V QUAD UART
EFR[5]: Special Character Detect Enable
Logic 0 = Special Character Detect Disabled (default).
Logic 1 = Special Character Detect Enabled. The UART compares each incoming receive character with
data in Xoff-2 register. If a match exists, the received data will be transferred to FIFO and ISR bit-4 will be set
to indicate detection of the special character. Bit-0 corresponds with the LSB bit for the receive character. If
flow control is set for comparing Xon1, Xoff1 (EFR [1:0]=10) then flow control and special character work
normally. However, if flow control is set for comparing Xon2, Xoff2 (EFR[1:0]=01) then flow control works
normally, but Xoff2 will not go to the FIFO, and will generate an Xoff interrupt and a special character
interrupt.
EFR[6]: Auto RTS or DTR Flow Control Enable
RTS#/DTR# output may be used for hardware flow control by setting EFR bit-6 to logic 1. When Auto RTS/
DTR is selected, an interrupt will be generated when the receive FIFO is filled to the programmed trigger level
and RTS/DTR# will de-assert (HIGH) at the next upper trigger or selected hysteresis level. RTS/DTR# will re-
assert (LOW) when FIFO data falls below the next lower trigger or selected hysteresis level (see FCTR bits 4-
7). The RTS# or DTR# output must be asserted (LOW) before the auto RTS/DTR can take effect. The selection
for RTS# or DTR# is through MCR bit-2. RTS/DTR# pin will function as a general purpose output when
hardware flow control is disabled.
Logic 0 = Automatic RTS/DTR flow control is disabled (default).
Logic 1 = Enable Automatic RTS/DTR flow control.
EFR[7]: Auto CTS Flow Control Enable
Automatic CTS or DSR Flow Control.
Logic 0 = Automatic CTS/DSR flow control is disabled (default).
Logic 1 = Enable Automatic CTS/DSR flow control. Transmission stops when CTS/DSR# pin de-asserts
(HIGH). Transmission resumes when CTS/DSR# pin is asserted (LOW). The selection for CTS# or DSR# is
through MCR bit-2.
4.14
TXCNT[7:0]: Transmit FIFO Level Counter - Read Only
Transmit FIFO level byte count from 0x00 (zero) to 0x40 (64). This 8-bit register gives an indication of the
number of characters in the transmit FIFO. The FIFO level Byte count register is read only. The user can take
advantage of the FIFO level byte counter for faster data loading to the transmit FIFO., which reduces CPU
bandwidth requirements.
4.15
TXTRG [7:0]: Transmit FIFO Trigger Level - Write Only
An 8-bit value written to this register sets the TX FIFO trigger level from 0x00 (zero) to 0x40 (64). The TX FIFO
trigger level generates an interrupt whenever the data level in the transmit FIFO falls below this preset trigger
level.
4.16
RXCNT[7:0]: Receive FIFO Level Counter - Read Only
Receive FIFO level byte count from 0x00 (zero) to 0x40 (64). It gives an indication of the number of characters
in the receive FIFO. The FIFO level byte count register is read only. The user can take advantage of the FIFO
level byte counter for faster data unloading from the receiver FIFO, which reduces CPU bandwidth
requirements.
4.17
RXTRG[7:0]: Receive FIFO Trigger Level - Write Only
An 8-bit value written to this register, sets the RX FIFO trigger level from 0x00 (zero) to 0x40 (64). The RX
FIFO trigger level generates an interrupt whenever the receive FIFO level rises to this preset trigger level.
相关PDF资料 |
PDF描述 |
|---|---|
| XR16C854CV-F | IC UART FIFO 128B QUAD 64LQFP |
| ST16C654IQ64-F | IC UART FIFO 64B QUAD 64LQFP |
| XR16V654IV-F | IC UART FIFO 64B QUAD 64LQFP |
| ST16C654CQ64-F | IC UART FIFO 64B QUAD 64LQFP |
| ST16C654DCQ64-F | IC UART FIFO 64B QUAD 64LQFP |
相关代理商/技术参数 |
参数描述 |
|---|---|
| XR16L784CVTR-F | 功能描述:UART 接口集成电路 3.3V QUAD UART RoHS:否 制造商:Texas Instruments 通道数量:2 数据速率:3 Mbps 电源电压-最大:3.6 V 电源电压-最小:2.7 V 电源电流:20 mA 最大工作温度:+ 85 C 最小工作温度:- 40 C 封装 / 箱体:LQFP-48 封装:Reel |
| XR16L784IV | 制造商:EXAR 制造商全称:EXAR 功能描述:HIGH PERFORMANCE 2.97V TO 5.5V QUAD UART |
| XR16L784IV-F | 功能描述:UART 接口集成电路 2.97V-5.5V 64B FIFO temp -45 to 85C RoHS:否 制造商:Texas Instruments 通道数量:2 数据速率:3 Mbps 电源电压-最大:3.6 V 电源电压-最小:2.7 V 电源电流:20 mA 最大工作温度:+ 85 C 最小工作温度:- 40 C 封装 / 箱体:LQFP-48 封装:Reel |
| XR16L784IVTR-F | 功能描述:UART 接口集成电路 PCI BUS QUAD UART RoHS:否 制造商:Texas Instruments 通道数量:2 数据速率:3 Mbps 电源电压-最大:3.6 V 电源电压-最小:2.7 V 电源电流:20 mA 最大工作温度:+ 85 C 最小工作温度:- 40 C 封装 / 箱体:LQFP-48 封装:Reel |
| XR16L788 | 制造商:EXAR 制造商全称:EXAR 功能描述:HIGH PERFORMANCE OCTAL UART |
发布紧急采购，3分钟左右您将得到回复。