参数资料
| 型号： | XR16L788CQ-F |
| 厂商： | Exar Corporation |
| 文件页数： | 18/54页 |
| 文件大小： | 0K |
| 描述： | IC UART 64B 3.3V OCTAL 100QFP |
| 标准包装： | 66 |
| 特点： | * |
| 通道数： | 8 |
| FIFO's： | 64 字节 |
| 规程： | RS485 |
| 电源电压： | 2.97 V ~ 5.5 V |
| 带自动流量控制功能： | 是 |
| 带IrDA 编码器/解码器： | 是 |
| 带故障启动位检测功能： | 是 |
| 带调制解调器控制功能： | 是 |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 100-BQFP |
| 供应商设备封装： | 100-QFP（14x20） |
| 包装： | 托盘 |
| 其它名称： | 1016-1283 |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页当前第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页第44页第45页第46页第47页第48页第49页第50页第51页第52页第53页第54页
XR16L788
25
REV. 1.2.3
HIGH PERFORMANCE 2.97V TO 5.5V OCTAL UART
3.1.5
RESET [7:0] (default 0x00)
The 8-bit RESET register provides the software with the ability to reset the UART(s) when there is a need.
Each bit is self-resetting after it is written a logic 1 to perform a reset to that channel. All registers in that
channel will be reset to the default condition, see Table 19 for details. As an example, bit-0 =1 resets UART
channel 0 with bit-7=1 resets channel 7.
3.1.6
SLEEP [7:0] (default 0x00)
The 8-bit Sleep register enables each UART separately to enter Sleep mode. Sleep mode reduces power
consumption when the system needs to put the UART(s) to idle. The UART enters sleep mode when there is
no interrupt pending. When all 8 UARTs are put to sleep, the on-chip oscillator shuts off to further conserve
power. In this case, the octal UART is awaken by any of the UART channel on from a receive data byte or a
change on the serial port. The UART is ready after 32 crystal clocks to ensure full functionality. Also, a special
interrupt is generated with an indication of no pending interrupt. Logic 0 (default) and logic 1 disable and
enable sleep mode respectively.
3.1.7
Device Identification and Revision
There are 2 internal registers that provide device identification and revision, DVID and DREV registers. The 8-
bit content in the DVID register provides device identification. A return value of 0x28 from this register indicates
the device is a XR16L788. The DREV register returns a 8-bit value of 0x01 for revision A, 0x02 for revision B
and so on. This information is very useful to the software driver for identifying which device it is communicating
with and to keep up with revision changes.
3.1.7.1
DVID [7:0] (default 0x28)
Device identification for the type of UART. The upper nibble indicates it is a XR16L78x series with lower nibble
indicating the number of channels.
Examples:
XR16L788 = 0x28
XR16L784 = 0x24
3.1.7.2
DREV [7:0] (default (0x01)
Revision number of the XR16L788. A 0x01 represents "revision-A" with 0x02 for rev-B and so forth.
Ch-6
Ch-7
Ch-5 Ch-4 Ch-3 Ch-2 Ch-1 Ch-0
RESET Register
Individual UART Channel Reset Enable
Bit-7 Bit-6 Bit-5 Bit-4 Bit-3 Bit-2 Bit-1 Bit-0
Ch-6
Ch-7
Ch-5 Ch-4 Ch-3 Ch-2 Ch-1 Ch-0
Bit-7 Bit-6 Bit-5 Bit-4 Bit-3 Bit-2 Bit-1 Bit-0
SLEEP Register
Individual UART Channel Sleep Enable
相关PDF资料 |
PDF描述 |
|---|---|
| XR16C864CQ-F | IC UART FIFO 128B QUAD 100QFP |
| XR17D154IV-F | IC UART PCI BUS QUAD 144LQFP |
| XR16C854IV-F | IC UART FIFO 128B QUAD 64LQFP |
| XR16C854DIV-F | IC UART FIFO 128B QUAD 64LQFP |
| XR16C854CQ-F | IC UART FIFO 128B QUAD 100QFP |
相关代理商/技术参数 |
参数描述 |
|---|---|
| XR16L788CQTR-F | 功能描述:UART 接口集成电路 3.3V OCTAL UART RoHS:否 制造商:Texas Instruments 通道数量:2 数据速率:3 Mbps 电源电压-最大:3.6 V 电源电压-最小:2.7 V 电源电流:20 mA 最大工作温度:+ 85 C 最小工作温度:- 40 C 封装 / 箱体:LQFP-48 封装:Reel |
| XR16L788IQ | 制造商:Exar Corporation 功能描述:3.3V OCTAL UART |
| XR16L788IQ-F | 功能描述:UART 接口集成电路 2.97V-5.5V 64B FIFO temp -45 to 85C RoHS:否 制造商:Texas Instruments 通道数量:2 数据速率:3 Mbps 电源电压-最大:3.6 V 电源电压-最小:2.7 V 电源电流:20 mA 最大工作温度:+ 85 C 最小工作温度:- 40 C 封装 / 箱体:LQFP-48 封装:Reel |
| XR16L788IQTR-F | 功能描述:UART 接口集成电路 3.3V OCTAL UART RoHS:否 制造商:Texas Instruments 通道数量:2 数据速率:3 Mbps 电源电压-最大:3.6 V 电源电压-最小:2.7 V 电源电流:20 mA 最大工作温度:+ 85 C 最小工作温度:- 40 C 封装 / 箱体:LQFP-48 封装:Reel |
| XR16M2550 | 制造商:EXAR 制造商全称:EXAR 功能描述:HIGH PERFORMANCE LOW VOLTAGE DUART WITH 16-BYTE FIFO |
发布紧急采购，3分钟左右您将得到回复。