参数资料
| 型号： | XR16V2650IL-F |
| 厂商： | Exar Corporation |
| 文件页数： | 22/47页 |
| 文件大小： | 0K |
| 描述： | IC UART FIFO 32B DUAL 32QFN |
| 标准包装： | 490 |
| 特点： | * |
| 通道数： | 2，DUART |
| FIFO's： | 32 字节 |
| 规程： | RS232，RS422 |
| 电源电压： | 2.25 V ~ 3.6 V |
| 带自动流量控制功能： | 是 |
| 带IrDA 编码器/解码器： | 是 |
| 带故障启动位检测功能： | 是 |
| 带调制解调器控制功能： | 是 |
| 带CMOS： | 是 |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 32-VFQFN 裸露焊盘 |
| 供应商设备封装： | 32-QFN 裸露焊盘（5x5） |
| 包装： | 托盘 |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页当前第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页第44页第45页第46页第47页
XR16V2650
29
REV. 1.0.2
HIGH PERFORMANCE DUART WITH 32-BYTE FIFO
LCR[6]: Transmit Break Enable
When enabled, the Break control bit causes a break condition to be transmitted (the TX output is forced to a
“space", LOW state). This condition remains, until disabled by setting LCR bit-6 to a logic 0.
Logic 0 = No TX break condition (default).
Logic 1 = Forces the transmitter output (TX) to a “space”, LOW, for alerting the remote receiver of a line
break condition.
LCR[7]: Baud Rate Divisors Enable
Baud rate generator divisor (DLL, DLM and DLD) enable.
Logic 0 = Data registers are selected (default).
Logic 1 = Divisor latch registers are selected.
4.7
Modem Control Register (MCR) or General Purpose Outputs Control - Read/Write
The MCR register is used for controlling the serial/modem interface signals or general purpose inputs/outputs.
MCR[0]: DTR# Output
The DTR# pin is a modem control output. If the modem interface is not used, this output may be used as a
general purpose output.
Logic 0 = Force DTR# output HIGH (default).
Logic 1 = Force DTR# output LOW.
MCR[1]: RTS# Output
The RTS# pin is a modem control output and may be used for automatic hardware flow control by enabled by
EFR bit-6. If the modem interface is not used, this output may be used as a general purpose output.
Logic 0 = Force RTS# HIGH (default).
Logic 1 = Force RTS# LOW.
MCR[2]: IrDA RX Inversion or OP1# (legacy term)
When Infrared mode is enabled (MCR[6]=1 and EFR[4]=1), this bit selects the idle state of the encoded IrDA
data. In internal loopback mode, this bit functions like the OP1# in the 16C550.
Logic 0 = Select RX input as active-low encoded IrDA data (Idle state will be low) (default).
Logic 1 = Select RX input as active-high encoded IrDA data (Idle state will be high).
In the Internal Loopback Mode, this bit controls the state of the modem input RI# bit in the MSR register as
shown in Figure 12.
MCR[3]: OP2# Output / INT Output Enable
This bit enables or disables the operation of INT, interrupt output. If INT output is not used, OP2# can be used
as a general purpose output.
Logic 0 = INT (A-B) outputs disabled (three state mode) and OP2# output set HIGH(default).
Logic 1 = INT (A-B) outputs enabled (active mode) and OP2# output set LOW.
MCR[4]: Internal Loopback Enable
Logic 0 = Disable loopback mode (default).
Logic 1 = Enable local loopback mode, see loopback section and Figure 12.
相关PDF资料 |
PDF描述 |
|---|---|
| ATMEGA324A-MCHR | IC MCU AVR 32K 20MHZ 44QFN |
| XR16L2752CJTR-F | IC UART FIFO 64B DUAL 44PLCC |
| ST16C650AIQ48TR-F | IC UART FIFO 32B 48TQFP |
| ST16C552ACJ68TR-F | IC UART FIFO 16B DUAL 68PLCC |
| ST16C650ACJ44TR-F | IC UART FIFO 32B 44PLCC |
相关代理商/技术参数 |
参数描述 |
|---|---|
| XR16V2650IM | 制造商:Rochester Electronics LLC 功能描述: 制造商:Exar Corporation 功能描述: |
| XR16V2650IM-0B-EB | 功能描述:UART 接口集成电路 Supports V2650 48 ld TQFP, PCI Interface RoHS:否 制造商:Texas Instruments 通道数量:2 数据速率:3 Mbps 电源电压-最大:3.6 V 电源电压-最小:2.7 V 电源电流:20 mA 最大工作温度:+ 85 C 最小工作温度:- 40 C 封装 / 箱体:LQFP-48 封装:Reel |
| XR16V2650IM-F | 功能描述:UART 接口集成电路 UART RoHS:否 制造商:Texas Instruments 通道数量:2 数据速率:3 Mbps 电源电压-最大:3.6 V 电源电压-最小:2.7 V 电源电流:20 mA 最大工作温度:+ 85 C 最小工作温度:- 40 C 封装 / 箱体:LQFP-48 封装:Reel |
| XR16V2650IMTR-F | 制造商:Exar Corporation 功能描述:UART 2-CH 32Byte FIFO 2.5V/3.3V 48-Pin TQFP T/R 制造商:Exar Corporation 功能描述:XR16V2650IMTR-F |
| XR16V2651 | 制造商:EXAR 制造商全称:EXAR 功能描述:HIGH PERFORMANCE DUART WITH 32-BYTE FIFO AND POWERSAVE |
发布紧急采购，3分钟左右您将得到回复。