参数资料
型号: XR16V2652IL-0B-EB
厂商: Exar Corporation
文件页数: 11/48页
文件大小: 0K
描述: EVAL BOARD FOR V2652 32QFN
标准包装: 1
系列: *
XR16V2652
19
REV. 1.0.2
HIGH PERFORMANCE DUART WITH 32-BYTE FIFO
2.19
Sleep Mode with Auto Wake-Up
The V2652 supports low voltage system designs, hence, a sleep mode is included to reduce its power
consumption when the chip is not actively used.
All of these conditions must be satisfied for the V2652 to enter sleep mode:
no interrupts pending for both channels of the V2652 (ISR bit-0 = 1)
sleep mode of both channels are enabled (IER bit-4 = 1)
modem inputs are not toggling (MSR bits 0-3 = 0)
RX input pins are idling HIGH
The V2652 stops its crystal oscillator to conserve power in the sleep mode. User can check the XTAL2 pin for
no clock output as an indication that the device has entered the sleep mode.
The V2652 resumes normal operation by any of the following:
a receive data start bit transition (HIGH to LOW)
a data byte is loaded to the transmitter, THR or FIFO
a change of logic state on any of the modem or general purpose serial inputs: CTS#, DSR#, CD#, RI#
If the V2652 is awakened by any one of the above conditions, it will return to the sleep mode automatically after
all interrupting conditions have been serviced and cleared. If the V2652 is awakened by the modem inputs, a
read to the MSR is required to reset the modem inputs. In any case, the sleep mode will not be entered while
an interrupt is pending from channel A or B. The V2652 will stay in the sleep mode of operation until it is
disabled by setting IER bit-4 to a logic 0.
If the address lines, data bus lines, IOW#, IOR#, CS#, CHSEL, and modem input lines remain steady when the
V2652 is in sleep mode, the maximum current will be in the microamp range as specified in the DC Electrical
Characteristics on page 37. If the input lines are floating or are toggling while the V2652 is in sleep mode, the
current can be up to 100 times more. If any of those signals are toggling or floating, then an external buffer
would be required to keep the address, data and control lines steady to achieve the low current. As an
alternative, please refer to the XR16V2651 which is pin-to-pin and software compatible with the V2652 but with
some additional pins and the PowerSave feature that eliminates any unnecessary external buffer.
A word of caution: owing to the starting up delay of the crystal oscillator after waking up from sleep mode, the
first few receive characters may be lost. The number of characters lost during the restart also depends on your
operating data rate. More characters are lost when operating at higher data rate. Also, it is important to keep
RX A/B inputs idling HIGH or “marking” condition during sleep mode to avoid receiving a “break” condition
upon the restart. This may occur when the external interface transceivers (RS-232, RS-422 or another type)
are also put to sleep mode and cannot maintain the “marking” condition. To avoid this, the designer can use a
47k-100k ohm pull-up resistor on the RXA and RXB pins.
相关PDF资料
PDF描述
5022-392J INDUCTOR 3.90UH 5% TOLERANCE SMD
GSM11DRTN-S13 CONN EDGECARD 22POS .156 EXTEND
RCM10DTKI-S288 CONN EDGECARD 20POS .156 EXTEND
A3DDB-1636G IDC CABLE- AKR16B/AE16G/AKR16B
MCP1316T-29LE/OT IC SUPERVISOR 2.90V P-P SOT23-5
相关代理商/技术参数
参数描述
XR16V2652IL32 制造商:EXAR 制造商全称:EXAR 功能描述:HIGH PERFORMANCE DUART WITH 32-BYTE FIFO
XR16V2652IL-F 功能描述:UART 接口集成电路 UART RoHS:否 制造商:Texas Instruments 通道数量:2 数据速率:3 Mbps 电源电压-最大:3.6 V 电源电压-最小:2.7 V 电源电流:20 mA 最大工作温度:+ 85 C 最小工作温度:- 40 C 封装 / 箱体:LQFP-48 封装:Reel
XR16V2652ILTR-F 制造商:Exar Corporation 功能描述:UART 2-CH 32Byte FIFO 2.5V/3.3V 32-Pin QFN EP T/R 制造商:Exar Corporation 功能描述:XR16V2652ILTR-F
XR16V2750 制造商:EXAR 制造商全称:EXAR 功能描述:HIGH PERFORMANCE DUART WITH 64-BYTE FIFO
XR16V2750_07 制造商:EXAR 制造商全称:EXAR 功能描述:HIGH PERFORMANCE DUART WITH 64-BYTE FIFO