- 您现在的位置：买卖IC网 > PDF目录18828 > XR18W750IL48-F (Exar Corporation)IC WIRELESS UART CTRLR 48QFN PDF资料下载
参数资料
| 型号： | XR18W750IL48-F |
| 厂商： | Exar Corporation |
| 文件页数： | 24/44页 |
| 文件大小： | 0K |
| 描述： | IC WIRELESS UART CTRLR 48QFN |
| 标准包装： | 260 |
| 功能： | 控制器 |
| RF 型： | 通用 |
| 次要属性： | I²C 接口 |
| 封装/外壳： | 48-VFQFN 裸露焊盘 |
| 包装： | 托盘 |
| 其它名称： | 1016-1473 XR18W750IL48-F-ND |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页当前第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页第44页
XR18W750
WIRELESS UART CONTROLLER
REV. 1.0.0
FCR[2]: TX FIFO Reset
This bit is only active when FCR bit-0 is a ‘1’.
? Logic 0 = No transmit FIFO reset (default).
? Logic 1 = Reset the transmit FIFO pointers and FIFO level counter logic (the transmit shift register is not
cleared or altered). This bit will return to a logic 0 after resetting the FIFO.
FCR[3]: DMA Mode Select
Controls the behavior of the TXRDY# and RXRDY# pins. See DMA operation section for details.
? Logic 0 = Normal Operation (default).
? Logic 1 = DMA Mode.
FCR[5:4]: Transmit FIFO Trigger Select
(logic 0 = default, TX trigger level = 1)
These 2 bits set the trigger level for the transmit FIFO. The UART will issue a transmit interrupt when the
number of characters in the FIFO falls below the selected trigger level, or when it gets empty in case that the
FIFO did not get filled over the trigger level on last re-load. Table 10 below shows the selections. EFR bit-4
must be set to ‘1’ before these bits can be accessed. Note that the receiver and the transmitter cannot use
different trigger tables. Whichever selection is made last applies to both the RX and TX side.
FCR[7:6]: Receive FIFO Trigger Select
(logic 0 = default, RX trigger level =1)
The FCTR Bits 5-4 are associated with these 2 bits. These 2 bits are used to set the trigger level for the receive
FIFO. The UART will issue a receive interrupt when the number of the characters in the FIFO crosses the
trigger level. Table 10 shows the complete selections. Note that the receiver and the transmitter cannot use
different trigger tables. Whichever selection is made last applies to both the RX and TX side.
T ABLE 10: T RANSMIT AND R ECEIVE FIFO T RIGGER T ABLE AND L EVEL S ELECTION
T RIGGER
T ABLE
FCTR
B IT -5
FCTR
B IT -4
FCR
B IT -7
FCR
B IT -6
FCR
B IT -5
FCR
BIT -4
R ECEIVE
T RIGGER L EVEL
T RANSMIT
T RIGGER
L EVEL
C OMPATIBILITY
Table-A
0
0
0
0
1 (default)
16C550, 16C2550,
0
0
1
1
0
1
0
1
1 (default)
4
8
14
16C2552, 16C554,
16C580
Table-B
0
1
0
0
16
16C650A
0
1
1
1
0
1
8
24
30
0
0
1
1
0
1
0
1
24
8
16
24
28
相关PDF资料 |
PDF描述 |
|---|---|
| 5026-84 | BANTAM PLUG/2 ALLIGATOR CLIP 84" |
| 4772-12-0 | PIN TIP PLUG/.025 SQ RCPT 12"BLK |
| 4741-24-9 | CORD .025 SQ PIN RCPT 24" WHITE |
| AN920031 | TLAPS SENSOR DL NO MAG 0-180DEG |
| D3V-21G3-1C4A-K | SWITCH LEVER 20A SPDT .250 QC |
相关代理商/技术参数 |
参数描述 |
|---|---|
| XR18W750IL48TR-F | 功能描述:UART 接口集成电路 XR18W750IL48TR-F RoHS:否 制造商:Texas Instruments 通道数量:2 数据速率:3 Mbps 电源电压-最大:3.6 V 电源电压-最小:2.7 V 电源电流:20 mA 最大工作温度:+ 85 C 最小工作温度:- 40 C 封装 / 箱体:LQFP-48 封装:Reel |
| XR18W753 | 制造商:EXAR 制造商全称:EXAR 功能描述:SINGLE CHIP 868MHZ TO 956MHZ RF TRANSCEIVER |
| XR18W753IL48 | 制造商:EXAR 制造商全称:EXAR 功能描述:SINGLE CHIP 868MHZ TO 956MHZ RF TRANSCEIVER |
| XR18W753IL48-F | 功能描述:射频接收器 UART RoHS:否 制造商:Skyworks Solutions, Inc. 类型:GPS Receiver 封装 / 箱体:QFN-24 工作频率:4.092 MHz 工作电源电压:3.3 V 封装:Reel |
| XR18W753L48-0A-EB | 功能描述:界面开发工具 900MHz RF EVAL Board RoHS:否 制造商:Bourns 产品:Evaluation Boards 类型:RS-485 工具用于评估:ADM3485E 接口类型:RS-485 工作电源电压:3.3 V |
发布紧急采购，3分钟左右您将得到回复。