- 您现在的位置：买卖IC网 > PDF目录16513 > XR19L200IL32-0B-EB (Exar Corporation)EVAL BOARD FOR XR19L200 32QFN PDF资料下载
参数资料
| 型号： | XR19L200IL32-0B-EB |
| 厂商： | Exar Corporation |
| 文件页数： | 3/40页 |
| 文件大小： | 0K |
| 描述： | EVAL BOARD FOR XR19L200 32QFN |
| 标准包装： | 1 |
| 系列： | * |
第1页第2页当前第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页
XR19L200
11
REV. 1.0.2
SINGLE CHANNEL INTEGRATED UART AND RS-232 TRANSCEIVER
upon receiving a character or delay until it reaches the FIFO trigger level. Furthermore, data delivery to the
host is guaranteed by a receive data ready time-out interrupt when data is not received for 4 word lengths as
defined by LCR[1:0] plus 12 bits time. This is equivalent to 3.7-4.6 character times. The RHR interrupt is
enabled by IER bit-0.
2.11.1
Receive Holding Register (RHR) - Read-Only
The Receive Holding Register is an 8-bit register that holds a receive data byte from the Receive Shift
Register. It provides the receive data interface to the host processor. The RHR register is part of the receive
FIFO of 16 bytes by 11-bits wide, the 3 extra bits are for the 3 error tags to be reported in LSR register. When
the FIFO is enabled by FCR bit-0, the RHR contains the first data character received by the FIFO. After the
RHR is read, the next character byte is loaded into the RHR and the errors associated with the current data
byte are immediately updated in the LSR bits 2-4.
2.12
Auto Xon/Xoff (Software) Flow Control
When software flow control is enabled (See Table 10), the L200 compares one or two sequential receive data
characters with the programmed Xon or Xoff-1,2 character value(s). If receive character(s) (RX) match the
programmed values, the L200 will halt transmission (TX) as soon as the current character has completed
transmission. When a match occurs, the Xoff (if enabled via IER bit-5) flag will be set and the interrupt output
pin will be activated. Following a suspension due to a match of the Xoff character, the L200 will monitor the
receive data stream for a match to the Xon-1,2 character. If a match is found, the L200 will resume operation
and clear the flags (ISR bit-4).
Reset initially sets the contents of the Xon/Xoff 8-bit flow control registers to a logic 0. Following reset the user
can write any Xon/Xoff value desired for software flow control. Different conditions can be set to detect Xon/
Xoff characters (See Table 10) and suspend/resume transmissions. When double 8-bit Xon/Xoff characters
are selected, the L200 compares two consecutive receive characters with two software flow control 8-bit
values (Xon1, Xon2, Xoff1, Xoff2) and controls TX transmissions accordingly. Under the above described flow
control mechanisms, flow control characters are not placed (stacked) in the user accessible RX data buffer or
FIFO.
In the event that the receive buffer is overfilling and flow control needs to be executed, the L200 automatically
sends an Xoff message (when enabled) via the serial TX output to the remote modem. The L200 sends the
Xoff character(s) two-character-times (= time taken to send two characters at the programmed baud rate) after
the receive FIFO crosses the programmed trigger level. To clear this condition, the L200 will transmit the
programmed Xon character(s) as soon as receive FIFO is less than one trigger level below the programmed
trigger level (see Table 8). The table below describes this.
FIGURE 8. RECEIVER OPERATION IN NON-FIFO MODE
Receive Data Shift
Register (RSR)
Receive
Data Byte
and Errors
RHR Interrupt (ISR bit-2)
Receive Data
Holding Register
(RHR)
RXFIFO1
16X Clock
Receive Data Characters
Data Bit
Validation
Error
Tags in
LSR bits
4:2
相关PDF资料 |
PDF描述 |
|---|---|
| VI-JVK-EZ-S | CONVERTER MOD DC/DC 40V 25W |
| 6374615-9 | C/A LC-SC DUP 62.5/125, 9M |
| ESC12DRTH-S13 | CONN EDGECARD 24POS .100 EXTEND |
| VE-JTK-EX | CONVERTER MOD DC/DC 40V 75W |
| 1-5503995-0 | CA 62.5/125UM ZIP OMCER 1.22 |
相关代理商/技术参数 |
参数描述 |
|---|---|
| XR19L200IL32-F | 功能描述:UART 接口集成电路 UART RoHS:否 制造商:Texas Instruments 通道数量:2 数据速率:3 Mbps 电源电压-最大:3.6 V 电源电压-最小:2.7 V 电源电流:20 mA 最大工作温度:+ 85 C 最小工作温度:- 40 C 封装 / 箱体:LQFP-48 封装:Reel |
| XR19L202 | 制造商:EXAR 制造商全称:EXAR 功能描述:TWO CHANNEL INTEGRATED UART AND RS-232 TRANSCEIVER |
| XR19L202IL48 | 制造商:EXAR 制造商全称:EXAR 功能描述:TWO CHANNEL INTEGRATED UART AND RS-232 TRANSCEIVER |
| XR19L202IL48-0B-EB | 功能描述:界面开发工具 Supports L202 48 pin QFN,PCI Interface RoHS:否 制造商:Bourns 产品:Evaluation Boards 类型:RS-485 工具用于评估:ADM3485E 接口类型:RS-485 工作电源电压:3.3 V |
| XR19L202IL48-F | 功能描述:UART 接口集成电路 UART RoHS:否 制造商:Texas Instruments 通道数量:2 数据速率:3 Mbps 电源电压-最大:3.6 V 电源电压-最小:2.7 V 电源电流:20 mA 最大工作温度:+ 85 C 最小工作温度:- 40 C 封装 / 箱体:LQFP-48 封装:Reel |
发布紧急采购，3分钟左右您将得到回复。