参数资料
| 型号： | XR19L210IL40-F |
| 厂商： | Exar Corporation |
| 文件页数： | 4/43页 |
| 文件大小： | 0K |
| 描述： | IC UART/TXRX RS232 40QFN |
| 标准包装： | 490 |
| 特点： | * |
| 通道数： | 1，UART |
| FIFO's： | 16 字节 |
| 规程： | RS232 |
| 电源电压： | 3 V ~ 5.5 V |
| 带自动流量控制功能： | 是 |
| 带故障启动位检测功能： | 是 |
| 带调制解调器控制功能： | 是 |
| 带CMOS： | 是 |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 40-VFQFN 裸露焊盘 |
| 供应商设备封装： | 40-QFN 裸露焊盘（6x6） |
| 包装： | 托盘 |
第1页第2页第3页当前第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页
XR19L210
12
SINGLE CHANNEL INTEGRATED UART AND RS-232 TRANSCEIVER
REV. 1.0.2
2.12
Auto RTS (Hardware) Flow Control
Automatic RTS hardware flow control is used to prevent data overrun to the local receiver FIFO. The RTS
output is used to request remote unit to suspend/resume data transmission. The auto RTS flow control
features is enabled to fit specific application requirement (see Figure 10):
Enable auto RTS flow control using EFR bit-6.
The auto RTS function must be started by asserting RTS output pin (MCR bit-1 to logic 1 after it is enabled).
If using the Auto RTS interrupt:
Enable RTS interrupt through IER bit-6 (after setting EFR bit-4). The UART issues an interrupt when the RTS
pin makes a transition from low to high: ISR bit-5 will be set to logic 1.
2.13
Auto RTS Hysteresis
The L210 has a new feature that provides flow control trigger hysteresis while maintaining compatibility with
the ST16C550 UART. With the Auto RTS function enabled, an interrupt is generated when the receive FIFO
reaches the programmed RX trigger level. The RTS pin will not be de-asserted until the receive FIFO reaches
one trigger level above the programmed trigger level in the trigger table (Table 8). The RTS pin will be re-
asserted after the RX FIFO is unloaded to one trigger level lower than the programmed trigger level. This is
described in Figure 10. Under the above described conditions, the L210 will continue to accept data until the
receive FIFO gets full. The Auto RTS function is initiated when the RTS output pin is asserted.
2.14
Auto CTS Flow Control
Automatic CTS flow control is used to prevent data overrun to the remote receiver FIFO. The CTS input is
monitored to suspend/restart the local transmitter. The auto CTS flow control feature is selected to fit specific
application requirement (see Figure 10):
Enable auto CTS flow control using EFR bit-7.
If using the Auto CTS interrupt:
Enable CTS interrupt through IER bit-7 (after setting EFR bit-4). The UART issues an interrupt when the CTS
pin is de-asserted: ISR bit-5 will be set to 1, and UART will suspend transmission as soon as the stop bit of
the character in process is shifted out. Transmission is resumed after the CTS input is re-asserted, indicating
more data may be sent.
相关PDF资料 |
PDF描述 |
|---|---|
| XR19L212IL48-F | IC UART/TXRX RS232 48QFN |
| XR19L220IL40-F | IC UART/TXRX RS232 40QFN |
| XR19L222IL64-F | IC UART/TXRX RS232 64QFN |
| XR19L400IL40-F | IC UART/TXRX RS485 40QFN |
| XR19L402IL48-F | IC UART/TXRX RS485 48QFN |
相关代理商/技术参数 |
参数描述 |
|---|---|
| XR19L212 | 制造商:EXAR 制造商全称:EXAR 功能描述:TWO CHANNEL INTEGRATED UART AND RS-232 TRANSCEIVER |
| XR19L212IL48 | 制造商:EXAR 制造商全称:EXAR 功能描述:TWO CHANNEL INTEGRATED UART AND RS-232 TRANSCEIVER |
| XR19L212IL48-0B-EB | 功能描述:界面开发工具 Supports L212 48 pin QFN, PCI Interface RoHS:否 制造商:Bourns 产品:Evaluation Boards 类型:RS-485 工具用于评估:ADM3485E 接口类型:RS-485 工作电源电压:3.3 V |
| XR19L212IL48-F | 功能描述:UART 接口集成电路 UART RoHS:否 制造商:Texas Instruments 通道数量:2 数据速率:3 Mbps 电源电压-最大:3.6 V 电源电压-最小:2.7 V 电源电流:20 mA 最大工作温度:+ 85 C 最小工作温度:- 40 C 封装 / 箱体:LQFP-48 封装:Reel |
| XR19L212IL48TR-F | 制造商:Exar Corporation 功能描述:UART 2-CH 64Byte FIFO 5V 48-Pin QFN EP T/R 制造商:Exar Corporation 功能描述:XR19L212IL48TR-F |
发布紧急采购，3分钟左右您将得到回复。