参数资料
型号: XR19L212IL48-F
厂商: Exar Corporation
文件页数: 8/52页
文件大小: 0K
描述: IC UART/TXRX RS232 48QFN
标准包装: 260
特点: *
通道数: 2,DUART
FIFO's: 64 字节
规程: RS232
电源电压: 3.3 V ~ 5.5 V
带自动流量控制功能:
带IrDA 编码器/解码器:
带故障启动位检测功能:
带调制解调器控制功能:
带CMOS:
安装类型: 表面贴装
封装/外壳: 48-VFQFN 裸露焊盘
供应商设备封装: 48-QFN-EP(7x7)
包装: 托盘
XR19L212
16
TWO CHANNEL INTEGRATED UART AND RS-232 TRANSCEIVER
REV. 1.0.1
NOTE: Table-B selected as Trigger Table for
2.13
Auto RTS (Hardware) Flow Control
Automatic RTS hardware flow control is used to prevent data overrun to the local receiver FIFO. The RTS
output is used to request remote unit to suspend/resume data transmission. The auto RTS flow control feature
is enabled to fit specific application requirement (see Figure 11):
Enable auto RTS flow control using EFR bit-6.
The auto RTS function must be started by asserting RTS output pin (MCR bit-1 to logic 1 after it is enabled).
If using the Auto RTS interrupt:
Enable RTS interrupt through IER bit-6 (after setting EFR bit-4). The UART issues an interrupt when the RTS
pin makes a transition from low to high: ISR bit-5 will be set to logic 1.
2.14
Auto RTS Hysteresis
The L212 has a new feature that provides flow control trigger hysteresis while maintaining compatibility with
the XR16C850, ST16C650A and ST16C550 family of UARTs. With the Auto RTS function enabled, an interrupt
is generated when the receive FIFO reaches the programmed RX trigger level. The RTS pin will not be de-
asserted until the receive FIFO reaches the upper limit of the hysteresis level. The RTS pin will be re-asserted
after the RX FIFO is unloaded to the lower limit of the hysteresis level. Under the above described conditions,
the L212 will continue to accept data until the receive FIFO gets full. The Auto RTS function is initiated when
the RTS output pin is asserted. Table 13 shows the complete details for the Auto RTS Hysteresis levels.
Please note that this table is for programmable trigger levels only (Table D). The hysteresis values for Tables
A-C are the next higher and next lower trigger levels in the corresponding table.
FIGURE 10. RECEIVER OPERATION IN FIFO AND AUTO RTS FLOW CONTROL MODE
Receive Data Shift
Register (RSR)
RXFIFO1
16X Clock
E
rro
rTag
s
(6
4-
set
s
)
Er
ro
rTag
s
in
LSR
bi
ts
4:2
64 bytes by 11-bit
wide FIFO
Receive Data Characters
FIFO Trigger=16
Example:
- RX FIFO trigger level selected at 16 bytes
(See Note below)
Data fills to 24
Data falls to 8
Data Bit
Validation
Receive
Data FIFO
Receive
Data
Receive Data
Byte and Errors
RHR Interrupt (ISR bit-2) programmed for
desired FIFO trigger level.
FIFO is Enabled by FCR bit-0=1
RTS# de-asserts when data fills above the flow
control trigger level to suspend remote transmitter.
Enable by EFR bit-6=1, MCR bit-1.
RTS# re-asserts when data falls below the flow
control trigger level to restart remote transmitter.
Enable by EFR bit-6=1, MCR bit-1.
相关PDF资料
PDF描述
XR19L220IL40-F IC UART/TXRX RS232 40QFN
XR19L222IL64-F IC UART/TXRX RS232 64QFN
XR19L400IL40-F IC UART/TXRX RS485 40QFN
XR19L402IL48-F IC UART/TXRX RS485 48QFN
XR20M1170IL24TR-F IC UART FIFO I2C/SPI 64B 24QFN
相关代理商/技术参数
参数描述
XR19L212IL48TR-F 制造商:Exar Corporation 功能描述:UART 2-CH 64Byte FIFO 5V 48-Pin QFN EP T/R 制造商:Exar Corporation 功能描述:XR19L212IL48TR-F
XR19L220 制造商:EXAR 制造商全称:EXAR 功能描述:SINGLE CHANNEL INTEGRATED UART AND RS-232 TRANSCEIVER
XR19L220_07 制造商:EXAR 制造商全称:EXAR 功能描述:SINGLE CHANNEL INTEGRATED UART AND RS-232 TRANSCEIVER
XR19L220IL40 制造商:EXAR 制造商全称:EXAR 功能描述:SINGLE CHANNEL INTEGRATED UART AND RS-232 TRANSCEIVER
XR19L220IL40-0A-EB 功能描述:界面开发工具 Supports L220 40 pin QFN, ISA Interface RoHS:否 制造商:Bourns 产品:Evaluation Boards 类型:RS-485 工具用于评估:ADM3485E 接口类型:RS-485 工作电源电压:3.3 V