参数资料
| 型号： | XR19L400IL40TR-F |
| 厂商： | Exar Corporation |
| 文件页数： | 10/46页 |
| 文件大小： | 0K |
| 描述： | IC UART/TXRX RS485 40QFN |
| 标准包装： | 3,000 |
| 特点： | * |
| 通道数： | 1，UART |
| FIFO's： | 64 字节 |
| 规程： | RS485 |
| 电源电压： | 3.3V，5V |
| 带自动流量控制功能： | 是 |
| 带故障启动位检测功能： | 是 |
| 带调制解调器控制功能： | 是 |
| 带CMOS： | 是 |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 40-VFQFN 裸露焊盘 |
| 供应商设备封装： | 40-QFN 裸露焊盘（6x6） |
| 包装： | 带卷 (TR) |
第1页第2页第3页第4页第5页第6页第7页第8页第9页当前第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页第44页第45页第46页
XR19L400
18
SINGLE CHANNEL INTEGRATED UART AND RS-485 TRANSCEIVER
REV. 1.0.3
2.12.3
UART sleep, Charge pump of RS-485 transceiver shut down (3.3V operation only)
If the ACP pin is HIGH and the UART portion of the L400 is in sleep mode, then the charge pump will shut
down immediately.
In this mode, the L400 shuts down the charge pump and tri-states the RS-485 drivers to conserve power. In
this mode, the RS-485 receivers are fully active and the internal registers of the L400 can be accessed. The
time for the charge pump to resume normal operation after exiting the sleep mode is typically 45
s. It will wake
up by any of the following:
■ a receive data start bit transition on the RX input (LOW to HIGH)
■ a data byte is loaded to the transmitter, THR or FIFO
■ a LOW to HIGH transition on any of the modem or general purpose serial inputs
2.12.3.1
Receiving data in UART sleep mode
There is a start-up delay for the crystal oscillator after waking up from sleep mode, therefore the first few
receive characters may be lost. The number of characters lost during the restart also depends on your
operating data rate. More characters are lost when operating at higher data rate. If an external oscillator is
used, any data received will be transferred to/from the UART without any issues.
2.12.3.2
Transmitting data in ACP mode
Since it takes the charge pump typically 45
s to resume normal operation after ACP mode has been disabled.
It is recommended that data not be transmitted until after this time.
2.12.4
Power-Save Feature
This mode is in addition to the sleep mode and in this mode, the core logic of the L400 is isolated from the CPU
interface. If the address lines, data bus lines, IOW#, IOR# and CS# remain steady when the L400 is in full
sleep mode, the maximum current will be in the microamp range as specified in the DC Electrical
Characteristics on page 37. However, if the input lines are floating or are toggling while the L400 is in sleep
mode, the current can be up to 100 times more. If not using the Power-Save feature, an external buffer would
be required to keep the address and data bus lines from toggling or floating to achieve the low current. But if
the Power-Save feature is enabled (PwrSave pin connected to VCC), this will eliminate the need for an
external buffer by internally isolating the address, data and control signals from other bus activities that could
cause wasteful power drain (see Figure 1). The L400 enters Power-Save mode when this pin is connected to
VCC, and the UART portion of the L400 is already in sleep mode.
Since Power-Save mode isolates the address, data and control signals, the device will wake-up only by:
■ a receive data start bit transition, or
■ a change of logic state on any of the modem or general purpose serial inputs: i.e., any of the MSR bits 0-
3 shows a ’1’
The L400 will return to the Power-Save mode automatically after a read to the MSR (to reset the modem
inputs) and all interrupting conditions have been serviced and cleared. The L400 will stay in the Power-Save
mode of operation until it is disabled by setting IER bit-4 to a logic 0 and/or the Power-Save pin is connected to
GND.
If the L400 is awakened by any one of the above conditions, it issues an interrupt as soon as the oscillator
circuit is up and running and the device is ready to transmit/receive. This interrupt has the same encoding (bit-
0 of ISR register = 1) as "no interrupt pending" and will clear when the ISR register is read. This will show up in
the ISR register only if no other interrupts are enabled.
相关PDF资料 |
PDF描述 |
|---|---|
| XR16M680IB25-F | IC UART FIFO 32B 25BGA |
| XR16M670IB25-F | IC UART FIFO 32B 25BGA |
| XR20M1170IL16TR-F | IC UART FIFO I2C/SPI 64B 16QFN |
| XR16M580IB25-F | IC UART FIFO 16B 25BGA |
| XR16M570IB25-F | IC UART FIFO 16B 25BGA |
相关代理商/技术参数 |
参数描述 |
|---|---|
| XR19L402 | 制造商:EXAR 制造商全称:EXAR 功能描述:TWO CHANNEL INTEGRATED UART AND RS-485 TRANSCEIVER |
| XR19L402_09 | 制造商:EXAR 制造商全称:EXAR 功能描述:TWO CHANNEL INTEGRATED UART AND RS-485 TRANSCEIVER |
| XR19L402IL48 | 制造商:EXAR 制造商全称:EXAR 功能描述:TWO CHANNEL INTEGRATED UART AND RS-485 TRANSCEIVER |
| XR19L402IL48-0B-EB | 功能描述:界面开发工具 Supports L402 48 pin QFN, PCI Interface RoHS:否 制造商:Bourns 产品:Evaluation Boards 类型:RS-485 工具用于评估:ADM3485E 接口类型:RS-485 工作电源电压:3.3 V |
| XR19L402IL48-F | 功能描述:UART 接口集成电路 UART RoHS:否 制造商:Texas Instruments 通道数量:2 数据速率:3 Mbps 电源电压-最大:3.6 V 电源电压-最小:2.7 V 电源电流:20 mA 最大工作温度:+ 85 C 最小工作温度:- 40 C 封装 / 箱体:LQFP-48 封装:Reel |
发布紧急采购，3分钟左右您将得到回复。