参数资料
| 型号： | XR19L400IL40TR-F |
| 厂商： | Exar Corporation |
| 文件页数： | 8/46页 |
| 文件大小： | 0K |
| 描述： | IC UART/TXRX RS485 40QFN |
| 标准包装： | 3,000 |
| 特点： | * |
| 通道数： | 1，UART |
| FIFO's： | 64 字节 |
| 规程： | RS485 |
| 电源电压： | 3.3V，5V |
| 带自动流量控制功能： | 是 |
| 带故障启动位检测功能： | 是 |
| 带调制解调器控制功能： | 是 |
| 带CMOS： | 是 |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 40-VFQFN 裸露焊盘 |
| 供应商设备封装： | 40-QFN 裸露焊盘（6x6） |
| 包装： | 带卷 (TR) |
第1页第2页第3页第4页第5页第6页第7页当前第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页第44页第45页第46页
XR19L400
16
SINGLE CHANNEL INTEGRATED UART AND RS-485 TRANSCEIVER
REV. 1.0.3
2.12
Sleep Mode, ACP Mode and Power-Save Feature with Wake-Up Interrupt
2.12.1
UART sleep mode (3.3V or 5V operation)
The UART portion in the L400 can enter sleep mode if all of these conditions are satisfied:
■ no interrupts pending (ISR bit-0 = 1)
■ the 16-bit divisor programmed in DLM and DLL registers is a non-zero value
■ sleep mode is enabled (IER bit-4 = 1)
■ modem inputs are not toggling (MSR bits 0-3 = 0)
■ RX input pins are idle
The L400 stops its crystal oscillator to conserve power in this mode. The user can check the XTAL2 pin for no
clock output as an indication that the device has entered the partial sleep mode.
The UART portion in the L400 resumes normal operation or active mode by any of the following:
■ a receive data start bit transition on the RX inputs
■ a data byte is loaded to the transmitter, THR or FIFO
■ a change of logic state on any of the modem or general purpose serial inputs: i.e., any of the MSR bits 0-
3 shows a ’1’ (in internal loopback mode)
If the sleep mode is enabled and the L400 is awakened by one of the conditions described above, an interrupt
is issued by the L400 to signal to the CPU that it is awake. The lower nibble of the interrupt source register
(ISR) will read a value of 0x1 for this interrupt and reading the ISR clears this interrupt. Since the same value
(0x1) is also used to indicate no pending interrupt, users should exercise caution while using the sleep mode.
The UART portion in the L400 will return to the sleep mode automatically after all interrupting conditions have
been serviced and cleared. If the UART portion of the L400 is awakened by the modem inputs, a read to the
MSR is required to reset the modem inputs. In any case, the sleep mode will not be entered while an interrupt
is pending. The UART portion of the L400 will stay in the sleep mode of operation until it is disabled by setting
IER bit-4 to a logic 0.
2.12.1.1
Receiving data in UART sleep mode
There is a start-up delay for the crystal oscillator after waking up from sleep mode, therefore the first few
receive characters may be lost. The number of characters lost during the restart also depends on your
operating data rate. More characters are lost when operating at higher data rate. If an external oscillator is
used, any data received will be transferred to/from the UART without any issues.
2.12.2
UART active, Charge pump of RS-485 transceiver shut down (3.3V operation only)
If the ACP pin is HIGH and the UART portion of the L400 is not in sleep mode, then the charge pump will
automatically shut down to conserve power if the following conditions are true:
■ no activity on the TX output signals
■ modem inputs have been idle for approximately 30 seconds
When these conditions are satisfied, the L400 shuts down the charge pump and tri-states the RS-485 drivers
to conserve power. In this mode, the RS-485 receivers are fully active and the internal registers of the L400
can be accessed. The time for the charge pump to resume normal operation after exiting the sleep mode is
typically 45
s. It will wake up by any of the following:
■ a receive data start bit transition on the RX input (LOW to HIGH)
■ a data byte is loaded to the transmitter, THR or FIFO
■ a LOW to HIGH transition on any of the modem or general purpose serial inputs
Because the receivers are fully active when the charge pump is turned off, any data received will be transferred
to/from the UART without any issues.
2.12.2.1
Transmitting data in ACP Mode
相关PDF资料 |
PDF描述 |
|---|---|
| XR16M680IB25-F | IC UART FIFO 32B 25BGA |
| XR16M670IB25-F | IC UART FIFO 32B 25BGA |
| XR20M1170IL16TR-F | IC UART FIFO I2C/SPI 64B 16QFN |
| XR16M580IB25-F | IC UART FIFO 16B 25BGA |
| XR16M570IB25-F | IC UART FIFO 16B 25BGA |
相关代理商/技术参数 |
参数描述 |
|---|---|
| XR19L402 | 制造商:EXAR 制造商全称:EXAR 功能描述:TWO CHANNEL INTEGRATED UART AND RS-485 TRANSCEIVER |
| XR19L402_09 | 制造商:EXAR 制造商全称:EXAR 功能描述:TWO CHANNEL INTEGRATED UART AND RS-485 TRANSCEIVER |
| XR19L402IL48 | 制造商:EXAR 制造商全称:EXAR 功能描述:TWO CHANNEL INTEGRATED UART AND RS-485 TRANSCEIVER |
| XR19L402IL48-0B-EB | 功能描述:界面开发工具 Supports L402 48 pin QFN, PCI Interface RoHS:否 制造商:Bourns 产品:Evaluation Boards 类型:RS-485 工具用于评估:ADM3485E 接口类型:RS-485 工作电源电压:3.3 V |
| XR19L402IL48-F | 功能描述:UART 接口集成电路 UART RoHS:否 制造商:Texas Instruments 通道数量:2 数据速率:3 Mbps 电源电压-最大:3.6 V 电源电压-最小:2.7 V 电源电流:20 mA 最大工作温度:+ 85 C 最小工作温度:- 40 C 封装 / 箱体:LQFP-48 封装:Reel |
发布紧急采购，3分钟左右您将得到回复。