- 您现在的位置：买卖IC网 > PDF目录11814 > XR20M1170IG24 (Exar Corporation)IC UART FIFO I2C/SPI 64B 24TSSOP PDF资料下载
参数资料
| 型号： | XR20M1170IG24 |
| 厂商： | Exar Corporation |
| 文件页数： | 3/56页 |
| 文件大小： | 0K |
| 描述： | IC UART FIFO I2C/SPI 64B 24TSSOP |
| 产品变化通告： | Leaded UART, V&I Obsolescence 11/Apr/2011 |
| 标准包装： | 62 |
| 特点： | * |
| 通道数： | 1，UART |
| FIFO's： | 64 字节 |
| 规程： | RS485 |
| 电源电压： | 2.25 V ~ 3.6 V |
| 带自动流量控制功能： | 是 |
| 带IrDA 编码器/解码器： | 是 |
| 带故障启动位检测功能： | 是 |
| 带调制解调器控制功能： | 是 |
| 带CMOS： | 是 |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 24-TSSOP（0.173"，4.40mm 宽） |
| 供应商设备封装： | 24-TSSOP |
| 包装： | 管件 |
第1页第2页当前第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页第44页第45页第46页第47页第48页第49页第50页第51页第52页第53页第54页第55页第56页
XR20M1170
11
REV. 1.1.0
I2C/SPI UART WITH 64-BYTE FIFO
2.5
Crystal Oscillator or External Clock Input
The M1170 includes an on-chip oscillator (XTAL1 and XTAL2) to produce a clock for both UART sections in the
device. The crystal oscillator provides a system clock to the Baud Rate Generators (BRG) section found in
each of the UART. XTAL1 is the input to the oscillator or external clock buffer input with XTAL2 pin being the
output. Please note that the input XTAL1 is not 5V tolerant and so the maximum at the pin should be VCC. For
programming details, see ““Section 2.6, Programmable Baud Rate Generator with Fractional Divisor” on
FIGURE 11. TYPICAL OSCILLATOR CONNECTIONS
C1
22-47 pF
C2
22-47 pF
Y1
1.8432 MHz
to
24 MHz
R1
0-120
(Optional)
R2
500Κ1Μ
XTAL1
XTAL2
The on-chip oscillator is designed to use an industry standard microprocessor crystal (parallel resonant,
fundamental frequency with 10-22 pF capacitance load, ESR of 20-120 ohms and 100 ppm frequency
tolerance) connected externally between the XTAL1 and XTAL2 pins (see Figure 11). The programmable
Baud Rate Generator is capable of operating with a crystal oscillator frequency of up to 24 MHz. However, with
an external clock input on XTAL1 pin, it can extend its operation up to 64 MHz (16 Mbps serial data rate) at
3.3V with an 4X sampling rate. For further reading on the oscillator circuit please see the Application Note
DAN108 on the EXAR web site at http://www.exar.com.
2.6
Programmable Baud Rate Generator with Fractional Divisor
Each UART has its own Baud Rate Generator (BRG) with a prescaler for the transmitter and receiver. The
prescaler is controlled by a software bit in the MCR register. The MCR register bit-7 sets the prescaler to divide
the input crystal or external clock by 1 or 4. The output of the prescaler clocks to the BRG. The BRG further
divides this clock by a programmable divisor between 1 and (216 - 0.0625) in increments of 0.0625 (1/16) to
obtain a 16X, 8X or 4X sampling clock of the serial data rate. The sampling clock is used by the transmitter for
data bit shifting and receiver for data sampling. The BRG divisor (DLL, DLM and DLD registers) defaults to the
value of ’1’ (DLL = 0x01, DLM = 0x00 and DLD = 0x00) upon power-up. Therefore, the BRG must be
programmed during initialization to the operating data rate. The DLL and DLM registers provide the integer part
of the divisor and the DLD register provides the fractional part of the dvisior. The four lower bits of the DLD are
used to select a value from 0 (for setting 0000) to 0.9375 or 15/16 (for setting 1111). Programming the Baud
Rate Generator Registers DLL, DLM and DLD provides the capability for selecting the operating data rate.
Table 6 shows the standard data rates available with a 24MHz crystal or external clock at 16X clock rate. If the
pre-scaler is used (MCR bit-7 = 1), the output data rate will be 4 times less than that shown in Table 6. At 8X
sampling rate, these data rates would double and at 4X sampling rate, these data rates would quadruple. Also,
when using 8X sampling mode, the bit time will have a jitter of ± 1/16 whenever the DLD is non-zero and is an
相关PDF资料 |
PDF描述 |
|---|---|
| VI-B7J-IW-F3 | CONVERTER MOD DC/DC 36V 100W |
| MS27497T18A35S | CONN RCPT 66POS WALL MNT W/SCKT |
| VI-B7L-IX-F2 | CONVERTER MOD DC/DC 28V 75W |
| SC16C752IB48,151 | IC UART DUAL W/FIFO 48-LQFP |
| VI-B7L-IW-F4 | CONVERTER MOD DC/DC 28V 100W |
相关代理商/技术参数 |
参数描述 |
|---|---|
| XR20M1170IG24-F | 功能描述:UART 接口集成电路 UART RoHS:否 制造商:Texas Instruments 通道数量:2 数据速率:3 Mbps 电源电压-最大:3.6 V 电源电压-最小:2.7 V 电源电流:20 mA 最大工作温度:+ 85 C 最小工作温度:- 40 C 封装 / 箱体:LQFP-48 封装:Reel |
| XR20M1170IG24TR-F | 制造商:Exar Corporation 功能描述:UART 1-CH 64Byte FIFO 1.8V/2.5V/3.3V 24-Pin TSSOP T/R 制造商:Exar Corporation 功能描述:XR20M1170IG24TR-F |
| XR20M1170IL16 | 制造商:EXAR 制造商全称:EXAR 功能描述:I2C/SPI UART WITH 64-BYTE FIFO |
| XR20M1170IL16-F | 功能描述:UART 接口集成电路 UART RoHS:否 制造商:Texas Instruments 通道数量:2 数据速率:3 Mbps 电源电压-最大:3.6 V 电源电压-最小:2.7 V 电源电流:20 mA 最大工作温度:+ 85 C 最小工作温度:- 40 C 封装 / 箱体:LQFP-48 封装:Reel |
| XR20M1170IL16TR-F | 功能描述:UART 接口集成电路 1.8V, 1 Ch. 64 Byte I2C / SPI UART RoHS:否 制造商:Texas Instruments 通道数量:2 数据速率:3 Mbps 电源电压-最大:3.6 V 电源电压-最小:2.7 V 电源电流:20 mA 最大工作温度:+ 85 C 最小工作温度:- 40 C 封装 / 箱体:LQFP-48 封装:Reel |
发布紧急采购，3分钟左右您将得到回复。