- 您现在的位置：买卖IC网 > PDF目录1976 > XR21V1412IL32TR-F (Exar Corporation)IC USB UART FIFO FULL SPD 32QFN PDF资料下载
参数资料
| 型号： | XR21V1412IL32TR-F |
| 厂商： | Exar Corporation |
| 文件页数： | 32/32页 |
| 文件大小： | 0K |
| 描述： | IC USB UART FIFO FULL SPD 32QFN |
| 产品培训模块： | XR21V141x Full-Speed USB UART Family |
| 标准包装： | 3,000 |
| 特点： | * |
| 通道数： | 2，DUART |
| FIFO's： | 128 字节，384 字节 |
| 规程： | USB 2.0 |
| 电源电压： | 2.97 V ~ 3.63 V |
| 带自动流量控制功能： | 是 |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 32-VFQFN 裸露焊盘 |
| 供应商设备封装： | 32-QFN 裸露焊盘（5x5） |
| 包装： | 带卷 (TR) |
| 配用： | 1016-1301-ND - EVAL BOARD FOR XR21V1412IL |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页当前第32页
XR21V1412
9
REV. 1.3.0
2-CH FULL-SPEED USB UART
Bit 6 is Self-powered mode - set to ’0’ for bus-powered, set to ’1’ for self-powered
Bit 5 is Remote Wakeup support - set to ’0’ for no support, set to ’1’ for remote wakeup support
Bit 4:0 are reserved - set to ’0’
1.3.1.4
Device Maximum Power
The Device Maximum Power value replaces the bMaxPower field in the USB Standard Configuration
Descriptor. The value specified is in units of 2 mA. For example, the value 0x2F is decimal 47 or 94 mA. Note
that the default bMaxPower of the V1412 device is 94 mA.
1.4
UART Manager
The UART Manager enables/disables each UART including the TX and RX FIFOs for each UART. The UART
Manager is located in a separate register block from the 2 UART channels.
1.5
UART
There are 2 enhanced UART channels in the V1412. Each UART channel is independent, therefore, they will
need to be initialized and configured independently. Each UART can be configured via USB control transfers
from the USB host. The UART transmitter and receiver sections are described seperately in the following
sections. At power-up, the V1412 will default to 9600 bps, 8 data bits, no parity bit, 1 stop bit, and no flow
control. If a standard CDC driver accesses the V1412, defaults will change. See ”Section 1.2, USB Device
Driver” on page 7.
1.5.1
Transmitter
The transmitter consists of a 128-byte TX FIFO and a Transmit Shift Register (TSR). Once a bulk-out packet
has been received and the CRC has been validated, the data bytes in that packet are written into the TX FIFO
of the specified UART channel. Data from the TX FIFO is transferred to the TSR when the TSR is idle or has
completed sending the previous data byte. The TSR shifts the data out onto the TX output pin at the data rate
defined by the CLOCK_DIVISOR and TX_CLOCK_MASK registers.
The transmitter sends the start bit
followed by the data bits (starting with the LSB), inserts the proper parity-bit if enabled, and adds the stop-
bit(s). The transmitter can be configured for 7 or 8 data bits with or without parity or 9 data bits without parity.
If 9 bit data is selected without wide mode, the 9th bit will always be ’0’.
1.5.1.1
Wide Mode Transmit
When both 9 bit data and wide mode are enabled, two bytes of data must be written. The first byte that is
loaded into the TX FIFO are the first 8 bits (data bits 7-0) of the 9-bit data. Bit-0 of the second byte that is
loaded into the TX FIFO is bit-8 of the 9-bit data. The data that is transmitted on the TX pin is as follows: start
bit, 9-bit data, stop bit. Use the WIDE_MODE register to enable wide mode.
1.5.2
Receiver
The receiver consists of a 384-byte RX FIFO and a Receive Shift Register (RSR). Data that is received in the
RSR via the RX pin is transferred into the RX FIFO. Data from the RX FIFO is transferred to the USB host in
response to a Bulk-In request. Depending on the mode, error / status information for that data character may
or may not be stored in the RX FIFO with the data.
1.5.2.1
Normal receive operation with 7 or 8-bit data
Data that is received is stored in the RX FIFO. Any parity, framing or overrun error or break status information
related to the data is discarded. Receive data format is shown in Figure 3.
1.5.2.2
Normal receive operation with 9-bit data
The first 8 bits of data received is stored in the RX FIFO. The 9th bit as well as any parity, framing or overrun
error or break status information related to the data is discarded.
相关PDF资料 |
PDF描述 |
|---|---|
| XR21V1414IM48-F | IC UART FIFO USB QUAD 48TQFP |
| XR3178EID-F | IC TXRX RS485 DIFF 3V 8NSOIC |
| XR5488EID-F | IC TXRX RS485 PROFIBUS 8NSOIC |
| XR68C681P-F | IC UART CMOS DUAL 40PDIP |
| XR68C92CJ-F | IC UART FIFO DUAL 44PLCC |
相关代理商/技术参数 |
参数描述 |
|---|---|
| XR21V1414 | 制造商:EXAR 制造商全称:EXAR 功能描述:4-CH FULL-SPEED USB UART |
| XR21V1414_10 | 制造商:EXAR 制造商全称:EXAR 功能描述:4-CH FULL-SPEED USB UART |
| XR21V1414IM-0A-EB | 功能描述:界面开发工具 Eval Board for XR21V1414IM48-F RoHS:否 制造商:Bourns 产品:Evaluation Boards 类型:RS-485 工具用于评估:ADM3485E 接口类型:RS-485 工作电源电压:3.3 V |
| XR21V1414IM-0B-EB | 功能描述:界面开发工具 For XR21V1414 TQFP48 USB, RS232;No Cables RoHS:否 制造商:Bourns 产品:Evaluation Boards 类型:RS-485 工具用于评估:ADM3485E 接口类型:RS-485 工作电源电压:3.3 V |
| XR21V1414IM48 | 制造商:EXAR 制造商全称:EXAR 功能描述:4-CH FULL-SPEED USB UART |
发布紧急采购，3分钟左右您将得到回复。