参数资料
型号: XR68M752IB-0A-EVB
厂商: Exar Corporation
文件页数: 51/54页
文件大小: 0K
描述: EVAL BOARD FOR 68M752 49BGA
标准包装: 1
系列: *
XR16M752/XR68M752
6
HIGH PERFORMANCE DUART WITH 64-BYTE FIFO
REV. 1.1.1
RXA
4
5
D2
I
UART channel A Receive Data or infrared receive data.
Normal receive data input must idle HIGH. The infrared
receiver pulses typically idles at LOW but can be inverted
by software control prior going in to the decoder, see
MCR[6]. If this pin is not used, tie it to VCC or pull it high
via a 100k ohm resistor.
RTSA#
23
33
D5
O
UART channel A Request-to-Send (active low) or general
purpose output. This output must be asserted prior to
using auto RTS flow control, see EFR[6] and IER[6]. For
auto RS485 half-duplex direction control, see DLD[6].
CTSA#
25
38
A5
I
UART channel A Clear-to-Send (active low) or general
purpose input. It can be used for auto CTS flow control,
see EFR[7] and IER[7]. This input should be connected to
VCC or GND when not used.
DTRA#
-
34
A7
O
UART channel A Data-Terminal-Ready (active low) or
general purpose output. If it is not used, leave it uncon-
nected.
DSRA#
-
39
B6
I
UART channel A Data-Set-Ready (active low) or general
purpose input. This input should be connected to VCC or
GND when not used.
CDA#
-
40
C5
I
UART channel A Carrier-Detect (active low) or general
purpose input. This input should be connected to VCC or
GND when not used.
RIA#
-
41
A4
I
UART channel A Ring-Indicator (active low) or general
purpose input. This input should be connected to VCC or
GND when not used.
OP2A#
-
32
C6
O
Output Port 2 Channel A - The output state is defined by
the user and through the software setting of MCR[3].
INTA is set to the active mode and OP2A# output LOW
when MCR[3] is set to a logic 1. INTA is set to the three
state mode and OP2A# output HIGH when MCR[3] is set
to a logic 0. See MCR[3]. If INTA is used, this output
should not be used as a general output else it will disturb
the INTA output functionality.
TXB
6
8
D1
O
UART channel B Transmit Data or infrared encoder data.
Standard transmit and receive interface is enabled when
MCR[6] = 0. In this mode, the TX signal will be HIGH dur-
ing reset or idle (no data). Infrared IrDA transmit and
receive interface is enabled when MCR[6] = 1. In the
Infrared mode, the inactive state (no data) for the Infrared
encoder/decoder interface is LOW. If it is not used, leave
it unconnected.
RXB
3
4
C3
I
UART channel B Receive Data or infrared receive data.
Normal receive data input must idle HIGH. The infrared
receiver pulses typically idles at logic 0 but can be
inverted by software control prior going in to the decoder,
see MCR[6]. If this pin is not used, tie it to VCC or pull it
high via a 100k ohm resistor.
Pin Description
NAME
32-QFN
PIN #
48-TQFP
PIN #
49-STBGA
PIN #
TYPE
DESCRIPTION
相关PDF资料
PDF描述
A3967SLBTR IC MOTOR DRIVER PWM FULL 24SOIC
VI-202-EX CONVERTER MOD DC/DC 15V 75W
EB83-S0D1840V CONN EDGEBOARD DUAL 36POS 5A
ECM22DRMI-S288 CONN EDGECARD 44POS .156 EXTEND
VI-201-EX CONVERTER MOD DC/DC 12V 75W
相关代理商/技术参数
参数描述
XR68M752IB-0B-EVB 功能描述:界面开发工具 Eval Board for XR68M752IB Series RoHS:否 制造商:Bourns 产品:Evaluation Boards 类型:RS-485 工具用于评估:ADM3485E 接口类型:RS-485 工作电源电压:3.3 V
XR68M752IB49 制造商:EXAR 制造商全称:EXAR 功能描述:HIGH PERFORMANCE DUART WITH 64-BYTE FIFO
XR68M752IB49-F 功能描述:UART 接口集成电路 W/64 BYTE FIFO RoHS:否 制造商:Texas Instruments 通道数量:2 数据速率:3 Mbps 电源电压-最大:3.6 V 电源电压-最小:2.7 V 电源电流:20 mA 最大工作温度:+ 85 C 最小工作温度:- 40 C 封装 / 箱体:LQFP-48 封装:Reel
XR68M752IL-0B-EB 功能描述:界面开发工具 Support XR68M752 32L QFN, PCI Interface RoHS:否 制造商:Bourns 产品:Evaluation Boards 类型:RS-485 工具用于评估:ADM3485E 接口类型:RS-485 工作电源电压:3.3 V
XR68M752IL32 制造商:EXAR 制造商全称:EXAR 功能描述:HIGH PERFORMANCE DUART WITH 64-BYTE FIFO