- 您现在的位置：买卖IC网 > PDF目录11834 > XR88C192IV-F (Exar Corporation)IC UART FIFO DUAL 44LQFP PDF资料下载
参数资料
| 型号： | XR88C192IV-F |
| 厂商： | Exar Corporation |
| 文件页数： | 14/32页 |
| 文件大小： | 0K |
| 描述： | IC UART FIFO DUAL 44LQFP |
| 标准包装： | 160 |
| 特点： | * |
| 通道数： | 2，DUART |
| FIFO's： | 16 字节 |
| 电源电压： | 2.97 V ~ 5.5 V |
| 带自动流量控制功能： | 是 |
| 带CMOS： | 是 |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 44-LQFP |
| 供应商设备封装： | 44-LQFP（10x10） |
| 包装： | 托盘 |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页当前第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页
XR88C92/192
21
Rev. 1.33
bit in this register is also a “1”, the -INT output will be
asserted. If the corresponding bit in this register is a
zero, the state of the bit in the interrupt status register
has no effect on the -INT output. Note that the interrupt
mask register does not have any effect on the program-
mable interrupt outputs OP7 through OP3 or the value
read from the interrupt status register.
0 = Interrupt output (-INT) disabled (default)
1 = Enable interrupt output for the event controlled by the
corresponding bit in ISR.
COUNTER / TIMER REGISTERS
The Preload value Upper (CTPU) and Lower (CTPL)
registers hold the most-significant byte and the least-
significant byte, respectively, of the value to be used by
the C/T (in both counter and timer modes). The C/T
Upper (CUR) and Lower Registers (CLR) give the
current value of the C/T, at the time they are read. In the
counter mode, the CUR and CLR should only be read
when the counter is stopped. Upon receiving a start
command after a stop command, the counter starts a
fresh cycle and begins counting down from the original
(preload) value written to CTPU and CTPL. Also chang-
ing the value of these registers does not take effect till
the current cycle is stopped and a subsequent start
command is issued.
In the timer mode, the CUR and CLR registers cannot
be read by the CPU. A stop command will not stop the
timer, but will only clear the counter ready status bit in
ISR (bit-3). Changing the value of the CTPU and CTPL
registers when the timer is running will change the
waveform after the current half-period of the square
wave. For more details, see the Counter/Timer section.
GENERAL PURPOSE REGISTER (GPR)
This is a general purpose scratchpad register which can
be used to store and retrieve one byte of user
infomation.
INPUT PORT REGISTER - Read Only
The current state of the multi-purpose inputs (IP0-IP6)
can be read via this register.
IPR Bit 0-6:
0 = Inputs are in low state.
1 = Inputs are in high state.
IPR Bit-7:
Not used and is set to “0”.
OUTPUT PORT CONFIGURATION REGISTER
(OPCR) - Write Only
This register selects following options for the multi-
purpose outputs OP2 to OP7.4Alternate functions of
OP1 and OP0 are controlled by the mode registers, not
the OPCR. MR1A Bit-7 and MR2A Bit-5 control OP0.
MR1B Bit-7 and MR2B Bit-5 control OP1. For more
details on these, see 'Multi-purpose Outputs' on page 8.
OP2 Output Select
Bit-1 Bit-0
0
Controlled by SOPR and ROPR
(default)
0
1
TxAClk16-Transmit A 16X clock
1
0
TxAClk1-Transmit A 1X clock
1
RxAClk1- Receive A 1X clock
OP3 Output Select
Bit-3 Bit-2
0
Controlled by SOPR and ROPR
(default)
0
1
C/T Output
1
0
TxBClk1-Transmit B 1X clock
1
RxBClk1- Receive B 1X clock
If OP3 is to be used for the timer output (a square wave
of the programmed frequency), program the counter/
timer for timer mode (ACR Bit-6 = 1), initialize the
counter/timer pre-load registers (CTPU and CTPL), and
read the 'Start C/T Command Register' (STCR) before
setting OPCR Bits 3-2 = 01. In the counter mode, the
output remains high until the terminal count is reached,
at which time it goes low. The output becomes high again
when the counter is stopped by a stop counter com-
mand.
OP4 output select (Bit 4):
0 = Controlled by SOPR and ROPR (default)
1 = -RxARDY which is the complement of ISR bit-1
OP5 output select (Bit 5):
0 = Controlled by SOPR and ROPR (default)
1 = -RxBRDY which is the complement of ISR bit-5
OP6 output select (Bit 6):
0 = Controlled by SOPR and ROPR (default)
1 = -TxARDY which is the complement of ISR bit-0
OP7 output select (Bit 7):
0 = Controlled by SOPR and ROPR (default)
1 = -TxBRDY which is the complement of ISR bit-4
相关PDF资料 |
PDF描述 |
|---|---|
| MS27484T8F35PA | CONN PLUG 6POS STRAIGHT W/PINS |
| ST16C2550IJ44-F | IC UART FIFO 16B DUAL 44PLCC |
| VI-JWJ-IW-F2 | CONVERTER MOD DC/DC 36V 100W |
| VI-JWJ-IW-F1 | CONVERTER MOD DC/DC 36V 100W |
| VI-JWH-IW-F4 | CONVERTER MOD DC/DC 52V 100W |
相关代理商/技术参数 |
参数描述 |
|---|---|
| XR88C192IVTR-F | 功能描述:UART 接口集成电路 Dual Channel UART RoHS:否 制造商:Texas Instruments 通道数量:2 数据速率:3 Mbps 电源电压-最大:3.6 V 电源电压-最小:2.7 V 电源电流:20 mA 最大工作温度:+ 85 C 最小工作温度:- 40 C 封装 / 箱体:LQFP-48 封装:Reel |
| XR88C681 | 制造商:EXAR 制造商全称:EXAR 功能描述:CMOS DUAL CHANNEL UART (DUART) |
| XR-88C681/24CN | 制造商:未知厂家 制造商全称:未知厂家 功能描述:UART |
| XR-88C681/24N | 制造商:未知厂家 制造商全称:未知厂家 功能描述:UART |
| XR-88C681/28CN | 制造商:未知厂家 制造商全称:未知厂家 功能描述:UART |
发布紧急采购，3分钟左右您将得到回复。