- 您现在的位置：买卖IC网 > PDF目录11834 > XR88C192IV-F (Exar Corporation)IC UART FIFO DUAL 44LQFP PDF资料下载
参数资料
| 型号： | XR88C192IV-F |
| 厂商： | Exar Corporation |
| 文件页数： | 16/32页 |
| 文件大小： | 0K |
| 描述： | IC UART FIFO DUAL 44LQFP |
| 标准包装： | 160 |
| 特点： | * |
| 通道数： | 2，DUART |
| FIFO's： | 16 字节 |
| 电源电压： | 2.97 V ~ 5.5 V |
| 带自动流量控制功能： | 是 |
| 带CMOS： | 是 |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 44-LQFP |
| 供应商设备封装： | 44-LQFP（10x10） |
| 包装： | 托盘 |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页当前第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页
XR88C92/192
23
Rev. 1.33
PROGRAMMING EXAMPLES
The following examples show how to initialize the XR88C92/192 for various operating conditions:
A) The first example will initialize channel A of an XR88C92 device for regular RX/TX. The operating parameters will
be 9600 baud, 8 word length, no parity and 1 stop bit.
Operation Register
Value
Remarks
Write
CRA
0x20
; reset RX (receiver)
Write
CRA
0x30
; reset TX (transmitter)
Write
CRA
0x40
; reset error status
Write
CRA
0xB0
; reset MR pointer to MR0
Write
MR0A
0x00
; use normal baud rate table. Now MR pointer points to MR1
Write
MR1A
0x13
; select word length & parity. Now MR pointer points to MR2
Write
MR2A
0x07
; normal mode (not loopback) & 1 stop bit
Write
CSRA
0xBB
; 9600 baud for RX & TX - clock source is XTAL1
Write
CRA
0x05
; enable RX & TX
Read
SRA
; should get a value 0x0C
B) This example will show how to use hardware flow control for both RX (RTS via OP0) and TX (CTS via IP0):
Write
CRA
0x10
; reset MR pointer to MR1
Write
MR1A
0x93
; select auto RTS control. The -RTS signal is sent via output OP0
Write
MR2A
0x17
; select auto CTS control. The input IP0 serves as the -CTS signal
C) This example will configure clock sources for TX and RX of both channels and C/T. Specifically, XTAL1 will be
used as channel A's TX clock; IP4 as channel A's 16X RX clock; IP5 as channel B's 1X TX clock and XTAL1 as
channel B's RX clock. Also, the C/T will be initialized in the timer mode and IP2 will be used as its clock source.
Some of these will be programmed to appear at the multi-purpose output pins:
Write
ACR
0x40
; C/T initialized in timer mode & IP2 chosen as its clock source
; also, bit-7 = 0, therefore baud rate Set1 has been selected
Write
CTPU
0x00
; It is essential to program CTPU & CTPL before programming OP3
Write
CTPL
0x05
; as C/T output (see below)
Write
CSRA
0xEB
; channel A RX clock source: IP4-16X, TX clock source: XTAL1 (if MR0A
; bits 2 and 0 = 0, the TX baud rate is 9600)
Write
CSRB
0xBF
; channel B RX clock source: XTAL1 (9600 baud), TX clock source: IP5-1X
Read
STCR
; Start the C/T
Write
OPCR
0x06
; C/T output appears at OP3 and channel A's TX 1X clock (this is XTAL1
; clock divided by 16) at OP2.
D) The next example will show how to configure and run channel B's transmitter in a multi-drop application. Note that
all other relevant parameters should be configured already, like baud rate etc.
Write
CRB
0x10
; reset MR pointer to MR1
Write
MR1B
0x1B
; word length = 8 and use A/D tag in the place of parity
Write
CRB
0x04
; Enable transmitter of channel B
Write
TXB
address
; Send the address first (A/D tag = 1)
Write
CRB
0x10
; reset MR pointer to MR1
Write
MR1B
0x13
; change A/D tag = 0
Write
TXB
data
; You can load the data (A/D tag = 0) immediately after the address. There
; is no need to wait till the transmitter is empty. Load all the data.
Read
SRB
; Check to see if the transmitter is empty & ready. You need to do this
; before you can load the next address.
; Repeat the last 5 steps to load different addresses and their data.
相关PDF资料 |
PDF描述 |
|---|---|
| MS27484T8F35PA | CONN PLUG 6POS STRAIGHT W/PINS |
| ST16C2550IJ44-F | IC UART FIFO 16B DUAL 44PLCC |
| VI-JWJ-IW-F2 | CONVERTER MOD DC/DC 36V 100W |
| VI-JWJ-IW-F1 | CONVERTER MOD DC/DC 36V 100W |
| VI-JWH-IW-F4 | CONVERTER MOD DC/DC 52V 100W |
相关代理商/技术参数 |
参数描述 |
|---|---|
| XR88C192IVTR-F | 功能描述:UART 接口集成电路 Dual Channel UART RoHS:否 制造商:Texas Instruments 通道数量:2 数据速率:3 Mbps 电源电压-最大:3.6 V 电源电压-最小:2.7 V 电源电流:20 mA 最大工作温度:+ 85 C 最小工作温度:- 40 C 封装 / 箱体:LQFP-48 封装:Reel |
| XR88C681 | 制造商:EXAR 制造商全称:EXAR 功能描述:CMOS DUAL CHANNEL UART (DUART) |
| XR-88C681/24CN | 制造商:未知厂家 制造商全称:未知厂家 功能描述:UART |
| XR-88C681/24N | 制造商:未知厂家 制造商全称:未知厂家 功能描述:UART |
| XR-88C681/28CN | 制造商:未知厂家 制造商全称:未知厂家 功能描述:UART |
发布紧急采购，3分钟左右您将得到回复。