- 您现在的位置：买卖IC网 > PDF目录11834 > XR88C92CV-F (Exar Corporation)IC UART FIFO DUAL 44LQFP PDF资料下载
参数资料
| 型号： | XR88C92CV-F |
| 厂商： | Exar Corporation |
| 文件页数： | 6/32页 |
| 文件大小： | 0K |
| 描述： | IC UART FIFO DUAL 44LQFP |
| 标准包装： | 160 |
| 特点： | * |
| 通道数： | 2，DUART |
| FIFO's： | 16 字节 |
| 电源电压： | 2.97 V ~ 5.5 V |
| 带自动流量控制功能： | 是 |
| 带CMOS： | 是 |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 44-LQFP |
| 供应商设备封装： | 44-LQFP（10x10） |
| 包装： | 托盘 |
| 其它名称： | XR88C92CV-F-ND |
第1页第2页第3页第4页第5页当前第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页
XR88C92/192
14
Rev. 1.33
INTERNAL REGISTER DESCRIPTIONS
A3 A2 A1 A0
READ Operation
WRITE Operation
0000
Mode Register A (MR0A, MR1A, MR2A)
0001
Status Register A (SRA)
Clock-Select Register A (CSRA)
0010
Reserved
Command Register A (CRA)
0011
Receiver Buffer A (RXA)
Transmitter Buffer A (TXA)
0100
Input Port Change Register (IPCR)
Auxiliary Control Register (ACR)
0101
Interrupt Status Register (ISR)
Interrupt Mask Register (IMR)
0110
Counter/Timer Upper Register (CUR)
C/T Preload value Upper Register (CTPU)
0111
Counter/Timer Lower Register (CLR)
C/T Preload value Lower Register (CTPL)
1000
Mode Register B (MR0B, MR1B, MR2B)
1001
Status Register B (SRB)
Clock-Select Register B (CSRB)
1010
Reserved
Command Register B (CRB)
1011
Receiver Buffer B (RXB)
Transmitter Buffer B (TXB)
1100
General Purpose Register (GPR)
1101
Input Port Register (IPR)
Output Port Configuration Register (OPCR)
1110
Start C/T Command (STCR)
Set Output Port Register (SOPR)
1111
Stop C/T Command (SPCR)
Reset Output Port Register (ROPR)
address 0xE) is read, the C/T terminates the current
countdown sequence and sets its output to a '1' (OP3
can be programmed to show this output). The C/T is
then initialized to the pre-load value, and begins a new
countdown sequence. When the terminal count is
reached (0x0000), the C/T sets its output to a '0'. Then,
it gets re-initialized to the pre-load value and repeats the
countdown sequence. See Figure 2 for the resulting
waveform.
The timer sets the C/T-ready bit in the interrupt status
register (ISR Bit-3) every other time it reaches the
terminal count (at every rising edge of the output). Users
can program the timer to generate an interrupt request
for this condition (every second countdown cycle) on
the -INT output. If the CPU changes the pre-load value,
the timer will not recognize the new value until either
(a) it reaches the next terminal count and is reinitialized
automatically, or
(b) it is forced to re-initialize by a start command.
When a read at the stop counter command address is
performed, the timer clears ISR Bit-3 but does not stop.
Because in timer mode the C/T runs continuously, it
should be completely configured (pre-load value loaded
and start counter command issued) before program-
ming the timer output to appear on OP3.
OTHER PROGRAMMING REMARKS
The contents of internal registers should not be changed
during receiver/transmitter operation as certain
changes can produce undesired results. For example,
changing the number of bits per character while the
transmitter is active will result in transmitting an incorrect
character. The contents of the clock-select register
(CSR) and ACR Bit-7 should only be changed after the
receiver(s) and transmitter(s) have been issued soft-
ware RX and TX reset commands. Similarly, changes
to the auxiliary control register (ACR Bits 4-6) should
only be made while the counter/timer (C/T) is not used.
The mode registers of each channel MR0, MR1 and
MR2 are accessed via an auxiliary pointer. The pointer
is set to mode register one (MR1) by RESET. It can be
set to MR0 or MR1 by issuing a “reset pointer” command
(0xB0 or 0x10 respectively) via the channel's command
register. Any read or write of the mode register switches
the pointer to next mode register. All accesses subse-
quent to reading/writing MR1 will address MR2 unless
the pointer is reset to MR0 or MR1 as described above.
The mode, command, clock-select, and status registers
are duplicated for each channel to allow independent
operation and control (except that both channels are
restricted to baud rates that are in the same set).
相关PDF资料 |
PDF描述 |
|---|---|
| D38999/20WC98S | CONN RCPT 10POS WALL MNT W/SCKT |
| XR88C681J-F | IC UART CMOS DUAL 44PLCC |
| ST16C552AIJ68-F | IC UART FIFO 16B DUAL 68PLCC |
| MS27474T10A98P | CONN RCPT 6POS JAM NUT W/PINS |
| XR88C192IV-F | IC UART FIFO DUAL 44LQFP |
相关代理商/技术参数 |
参数描述 |
|---|---|
| XR88C92CVTR-F | 功能描述:UART 接口集成电路 Dual Channel UART RoHS:否 制造商:Texas Instruments 通道数量:2 数据速率:3 Mbps 电源电压-最大:3.6 V 电源电压-最小:2.7 V 电源电流:20 mA 最大工作温度:+ 85 C 最小工作温度:- 40 C 封装 / 箱体:LQFP-48 封装:Reel |
| XR88C92IJ | 制造商:EXAR 制造商全称:EXAR 功能描述:DUAL UNIVERSAL ASYNCHRONOUS RECEIVER AND TRANSMITTER |
| XR88C92IJ-F | 功能描述:UART 接口集成电路 Dual Channel UART RoHS:否 制造商:Texas Instruments 通道数量:2 数据速率:3 Mbps 电源电压-最大:3.6 V 电源电压-最小:2.7 V 电源电流:20 mA 最大工作温度:+ 85 C 最小工作温度:- 40 C 封装 / 箱体:LQFP-48 封装:Reel |
| XR88C92IJTR-F | 功能描述:UART 接口集成电路 Dual Channel UART RoHS:否 制造商:Texas Instruments 通道数量:2 数据速率:3 Mbps 电源电压-最大:3.6 V 电源电压-最小:2.7 V 电源电流:20 mA 最大工作温度:+ 85 C 最小工作温度:- 40 C 封装 / 箱体:LQFP-48 封装:Reel |
| XR88C92IP | 制造商:EXAR 制造商全称:EXAR 功能描述:DUAL UNIVERSAL ASYNCHRONOUS RECEIVER AND TRANSMITTER |
发布紧急采购，3分钟左右您将得到回复。