参数资料
| 型号： | XRT5997IV-F |
| 厂商： | Exar Corporation |
| 文件页数： | 20/37页 |
| 文件大小： | 0K |
| 描述： | IC LIU E1 7CH 3.3V 100TQFP |
| 标准包装： | 90 |
| 类型： | 线路接口装置（LIU） |
| 驱动器/接收器数： | 7/7 |
| 规程： | E1 |
| 电源电压： | 3.14 V ~ 3.47 V |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 100-LQFP |
| 供应商设备封装： | 100-TQFP（14x14） |
| 包装： | 托盘 |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页当前第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页
XRT5997
27
Rev. 1.0.0
Capacitive-Coupling the Receiver to the Line
Figure 9, presents a recommended approach that the
user to employ when capacitive-coupling the Receive
Section to the line.
U1
XRT5997
RTIP_1
7
RRing_1
8
RxPOS_1
1
RxNEG_1
2
RxLOS_1
100
C1
0.1uF
1
2
C2
0.1uF
1
2
R2
37.4
1
2
R1
37.4
1
2
J1
BNC
1
2
RxPOS_1
RxNEG_1
Loss of Signal - 1
Figure 9. Recommended Schematic for Interfacing the Receive Sections of the XRT5997 Device to
the Line for 75
Applications (Capacitive-Coupling)
2.2 The “Receive Equalizer” Bock
After a given Channel (within the XRT5997 device) has
received the incoming line signal, via the RTIP_x and
RRing_x input pins, the first block that this signal will
pass through is the Receive Equalizer block.
As the line signal is transmitted from a given “Transmit-
ting” terminal, the pulse shapes (at that location) are
basically “square”. Hence, these pulses consist of a
combination of “low” and “high” frequency Fourier
components.
As this line signal travels from the
“transmitting terminal” (via the coaxial cable or twisted
pair) to the receiving terminal, it will be subjected to
“frequency-dependent” loss. In other words, the higher
frequency components of the signal will be subjected
to a greater amount of attenuation than the lower
frequency components. If this line signal travels over
reasonably long cable lengths, then the shape of the
pulses (which were originally square) will be distorted
and with inter-symbol interference increases.
The purpose of this block is to equalize the incoming
distorted signal, due to cable loss. In essence, the
Receive Equalizer block accomplishes this by subject-
ing the received line signal to “frequency-dependent”
amplification (which attempts to counter the fre-
quency-dependent loss that the line signal has experi-
enced).
By doing this, the Receive Equalizer is
attempting to restore the shape of the line signal so that
the received data can be recovered reliably.
相关PDF资料 |
PDF描述 |
|---|---|
| XRT6164AIP-F | IC TXRX DGTL INTERFACE 16PDIP |
| XRT6164CD-F | IC TXRX DGTL INTERFACE 16SOIC |
| XRT6165ID-F | IC DGTL DATA PROCESSOR 24SOIC |
| XRT6166CD-F | IC DGTL DATA PROCESSOR 28SOIC |
| XRT7295AEIW-F | IC E3 LINE RECEIVER 20SOJ |
相关代理商/技术参数 |
参数描述 |
|---|---|
| XRT5997IVTR-F | 功能描述:外围驱动器与原件 - PCI 7 Ch. E1 LIU RoHS:否 制造商:PLX Technology 工作电源电压: 最大工作温度: 安装风格:SMD/SMT 封装 / 箱体:FCBGA-1156 封装:Tray |
| XRT59L81IG-F | 功能描述:时钟发生器及支持产品 BITS Clock Generator RoHS:否 制造商:Silicon Labs 类型:Clock Generators 最大输入频率:14.318 MHz 最大输出频率:166 MHz 输出端数量:16 占空比 - 最大:55 % 工作电源电压:3.3 V 工作电源电流:1 mA 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:QFN-56 |
| XRT59L81IGTR-F | 功能描述:时钟发生器及支持产品 BITS Clock Generator RoHS:否 制造商:Silicon Labs 类型:Clock Generators 最大输入频率:14.318 MHz 最大输出频率:166 MHz 输出端数量:16 占空比 - 最大:55 % 工作电源电压:3.3 V 工作电源电流:1 mA 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:QFN-56 |
| XRT59L91 | 制造商:EXAR 制造商全称:EXAR 功能描述:Single-Chip E1 Line Interface Unit |
| XRT59L91ES | 功能描述:外围驱动器与原件 - PCI 1 CH E1 AFE RoHS:否 制造商:PLX Technology 工作电源电压: 最大工作温度: 安装风格:SMD/SMT 封装 / 箱体:FCBGA-1156 封装:Tray |
发布紧急采购，3分钟左右您将得到回复。