参数资料
型号: XRT7300IV-F
厂商: Exar Corporation
文件页数: 20/55页
文件大小: 0K
描述: IC LIU E3/DS3/STS-1 SGL 44TQFP
标准包装: 160
类型: 线路接口装置(LIU)
驱动器/接收器数: 1/1
规程: DS3,E3,STS-1
电源电压: 4.75 V ~ 5.25 V
安装类型: 表面贴装
封装/外壳: 44-LQFP
供应商设备封装: 44-TQFP(10x10)
包装: 托盘
其它名称: 1016-1635
XRT7300IV-F-ND
XRT7300
E3/DS3/STS-1 LINE INTERFACE UNIT
REV. 1.1.2
23
Figure 14 illustrates the HDB3 Encoder at work with
two separate strings of four (or more) consecutive ze-
ros.
2.3.3
Enabling/Disabling the HDB3/B3ZS
Encoder
The XRT7300 allows two methods to enable or dis-
able the HDB3/B3ZS Encoder.
If the XRT7300 is operating in the Hardware Mode.
To enable the HDB3/B3ZS Encoder, set the ENCO-
DIS input pin (pin 21) to “0”. To disable the HDB3/
B3ZS Encoder, set the ENCODIS input pin (pin 21) to
“1”.
If the XRT7300 is operating in the HOST Mode.
To enable the HDB3/B3ZS Encoder, set the ENCO-
DIS bit-field in Command Register (CR2) to “0”.
To disable the HDB3/B3ZS Encoder, set the ENCO-
DIS bit-field in Command Register (CR2) to “1”.
If either of these two methods is employed to disable
the HDB3/B3ZS Encoder, the LIU transmits the data
onto the line as it is received via the TPDATA and
TNDATA input pins.
2.4
THE TRANSMIT PULSE SHAPER CIRCUITRY
The Transmit Pulse Shaper Circuitry consists of a
Transmit Line Build-Out circuit which can be enabled
or disabled by setting the TXLEV input pin (or TXLEV
bit-field) to “High” or “Low”. The purpose of the
Transmit Line Build-Out circuit is to permit configuring
of the XRT7300 to transmit an output pulse which is
compliant to either of the following Bellcore pulse
template requirements when measured at the Digital
Cross Connect System. Each of these Bellcore spec-
ifications further state that the cable length between
the Transmit Output and the Digital Cross Connect
system can range anywhere from 0 to 450 feet.
The Isolated DSX-3 Pulse Template Requirement per
Bellcore GR-499-CORE is illustrated in Figure 7.
The Isolated STSX-1 Pulse Template Requirement
per Bellcore GR-253-CORE is illustrated in Figure 8.
2.4.1
Enabling the Transmit Line Build-Out Cir-
cuit
If the Transmit Line Build-Out Circuit is enabled, the
XRT7300 outputs shaped pulses onto the line via the
TTIP and TRING output pins.
Do the following to enable the Transmit Line Build-
Out circuit in the XRT7300:
If the XRT7300 is operating in the Hardware Mode,
set theTXLEV input pin (pin 1) to “Low”
If the XRT7300 is operating in the HOST Mode, set
the TXLEV bit-field to “0” as illustrated below.
2.4.2
Disabling the Transmit Line Build-Out Cir-
cuit
FIGURE 14. AN EXAMPLE OF HDB3 ENCODING
Data
TPDATA
TNDATA
1
0
1
0
1
0
1
0
1
0
1
0
1
0 0
0
V
Line Signal
B
0 0
V
TCLK
COMMAND REGISTER CR2 (ADDRESS = 0X02
D4
D3
D2
D1
D0
DECODIS ENCODIS ALOSDIS DLOSDIS
REQDIS
X
0
X
COMMAND REGISTER CR1 (ADDRESS = 0X01)
D4
D3
D2
D1
D0
TXOFF
TAOS
TXCLKINV
TXLEV
TXBIN
0
X
0
1
相关PDF资料
PDF描述
VI-JTZ-MW-S CONVERTER MOD DC/DC 2V 40W
VI-BNW-MX-F2 CONVERTER MOD DC/DC 5.5V 75W
LTC2619IGN#TRPBF IC DAC 14BIT R-R QUAD 16SSOP
SP510EM-L IC TXRX MULTIPROTOCOL HS 100LQFP
AD5334BRUZ-REEL IC DAC 8BIT QUAD VOUT 24TSSOP
相关代理商/技术参数
参数描述
XRT7300IVTR 功能描述:网络控制器与处理器 IC RoHS:否 制造商:Micrel 产品:Controller Area Network (CAN) 收发器数量: 数据速率: 电源电流(最大值):595 mA 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:PBGA-400 封装:Tray
XRT7300IVTR-F 功能描述:网络控制器与处理器 IC RoHS:否 制造商:Micrel 产品:Controller Area Network (CAN) 收发器数量: 数据速率: 电源电流(最大值):595 mA 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:PBGA-400 封装:Tray
XRT7302IV 制造商:未知厂家 制造商全称:未知厂家 功能描述:PCM Transceiver
XRT73L00 制造商:EXAR 制造商全称:EXAR 功能描述:E3/DS3/STS-1 LINE INTERFACE UNIT
XRT73L00A 制造商:EXAR 制造商全称:EXAR 功能描述:E3/DS3/STS-1 LINE INTERFACE UNIT