参数资料
| 型号： | XRT75L00DIV |
| 厂商： | Exar Corporation |
| 文件页数： | 81/92页 |
| 文件大小： | 0K |
| 描述： | IC LIU E3/DS3/STS-1 SGL 52TQFP |
| 标准包装： | 96 |
| 类型： | 线路接口装置（LIU） |
| 驱动器/接收器数： | 1/1 |
| 规程： | DS3，E3，STS-1，SONET |
| 电源电压： | 3.135 V ~ 3.465 V |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 52-LQFP |
| 供应商设备封装： | 52-TQFP（10x10） |
| 包装： | 托盘 |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页第44页第45页第46页第47页第48页第49页第50页第51页第52页第53页第54页第55页第56页第57页第58页第59页第60页第61页第62页第63页第64页第65页第66页第67页第68页第69页第70页第71页第72页第73页第74页第75页第76页第77页第78页第79页第80页当前第81页第82页第83页第84页第85页第86页第87页第88页第89页第90页第91页第92页
XRT75L00D
E3/DS3/STS-1 LINE INTERFACE UNIT WITH SONET DESYNCHRONIZER
REV. 1.0.2
77
Using a particular clock edge within the "gapped" clock signal (from the Mapper IC) to sample and latch the
value of each DS3 data-bit that is output from the Mapper IC.
To (through the user of the Jitter Attenuator block) attenuate the jitter within this "DS3 data" and "clock signal"
that is output from the Mapper IC.
To convert this "smoothed" DS3 data and clock into industry-compliant DS3 pulses, and to output these
pulses onto the line.
To configure the LIU to operate in the correct mode for this application, the user must execute the following
configuration steps.
a.
Configure the LIU to operate in the DS3 Mode
The user can configure a given channel (within the LIU) to operate in the DS3 Mode, by executing either of the
following steps.
If the LIU has been configured to operate in the Host Mode
The user can accomplish this by setting both Bits 2 (E3_n) and Bits 1 (STS-1/DS3*_n), within each of the
"Channel Control Registers" to "0" as depicted below.
If the LIU has been configured to operate in the Hardware Mode
The user can accomplish this by pulling all of the following input pins "Low".
Pin 76 - E3_0
Pin 94 - E3_1
Pin 85 - E3_2
Pin 72 - STS-1/DS3_0
Pin 98 - STS-1/DS3_1
Pin 81 - STS-1/DS3_2
b.
Configure the LIU to operate in the Single-Rail Mode
Since the Mapper IC will typically output a single "Data Line" and a "Clock Line" for each DS3 signal that it
demaps from the incoming STS-N signal, it is imperative to configure each channel within the LIU to operate in
the Single Rail Mode.
The user can accomplish this by executing either of the following steps.
If the LIU has been configured to operate in the Host Mode
The user can accomplish this by setting Bit 0 (SR/DR*), within the each of the "Channel Control" Registers to 1,
as illustrated below.
CHANNEL CONTROL REGISTER
Channel - 0 Address Location = 0x06, Channel - 1 Address Location = 0x0E, Channel - 2 Address Location = 0x16
BIT 7BIT 6BIT 5BIT 4BIT 3BIT 2BIT 1
BIT 0
Unused
PRBS Enable
Ch_n
RLB_n
LLB_n
E3_n
STS-1/DS3_n
SR/DR_n
R/O
R/W
00
000
00
0
相关PDF资料 |
PDF描述 |
|---|---|
| MS27466T11B98SA | CONN RCPT 6POS WALL MT W/SCKT |
| MS27466E15A15S | CONN RCPT 15POS WALL MT W/SCKT |
| VE-21W-MX-F2 | CONVERTER MOD DC/DC 5.5V 75W |
| XRT83SH314IB | IC LIU T1/E1/J1 14CH 304TBGA |
| MS27508E14B15SA | CONN RCPT 15POS BOX MNT W/SCKT |
相关代理商/技术参数 |
参数描述 |
|---|---|
| XRT75L00DIV-F | 功能描述:外围驱动器与原件 - PCI 1-Ch DS3, E3, SONET RoHS:否 制造商:PLX Technology 工作电源电压: 最大工作温度: 安装风格:SMD/SMT 封装 / 箱体:FCBGA-1156 封装:Tray |
| XRT75L00DIVTR | 功能描述:时钟合成器/抖动清除器 3.3V 1 CH E3/DS3/STS W/SONET DE-SYNCH RoHS:否 制造商:Skyworks Solutions, Inc. 输出端数量: 输出电平: 最大输出频率: 输入电平: 最大输入频率:6.1 GHz 电源电压-最大:3.3 V 电源电压-最小:2.7 V 封装 / 箱体:TSSOP-28 封装:Reel |
| XRT75L00DIVTR-F | 功能描述:时钟合成器/抖动清除器 3.3V 1 CH E3/DS3/STS W/SONET DE-SYNCH RoHS:否 制造商:Skyworks Solutions, Inc. 输出端数量: 输出电平: 最大输出频率: 输入电平: 最大输入频率:6.1 GHz 电源电压-最大:3.3 V 电源电压-最小:2.7 V 封装 / 箱体:TSSOP-28 封装:Reel |
| XRT75L00ES | 功能描述:时钟合成器/抖动清除器 1CH T3/E3/STS1 LIU+JA 3.3V RoHS:否 制造商:Skyworks Solutions, Inc. 输出端数量: 输出电平: 最大输出频率: 输入电平: 最大输入频率:6.1 GHz 电源电压-最大:3.3 V 电源电压-最小:2.7 V 封装 / 箱体:TSSOP-28 封装:Reel |
| XRT75L00IV | 功能描述:外围驱动器与原件 - PCI 3.3V 1 CH E3/DS3/STS W/JITTER ATTEN RoHS:否 制造商:PLX Technology 工作电源电压: 最大工作温度: 安装风格:SMD/SMT 封装 / 箱体:FCBGA-1156 封装:Tray |
发布紧急采购，3分钟左右您将得到回复。