参数资料
型号: XRT75L00DIVTR-F
厂商: Exar Corporation
文件页数: 51/92页
文件大小: 0K
描述: IC LIU E3/DS3/STS-1 SGL 52TQFP
标准包装: 1,000
类型: 线路接口装置(LIU)
驱动器/接收器数: 1/1
规程: DS3,E3,STS-1,SONET
电源电压: 3.135 V ~ 3.465 V
安装类型: 表面贴装
封装/外壳: 52-LQFP
供应商设备封装: 52-TQFP(10x10)
包装: 带卷 (TR)
XRT75L00D
REV. 1.0.2
E3/DS3/STS-1 LINE INTERFACE UNIT WITH SONET DESYNCHRONIZER
50
Telcordia GR-253-CORE’s recommendation on mapping DS3 data into an STS-1 SPE
An STS-1 frame is a data-structure that consists of 810 bytes (or 6480 bits). A given STS-1 frame can be
viewed as being a 9 row by 90 byte column array (making up the 810 bytes). The frame-repetition rate (for an
STS-1 frame) is 8000 frames/second. Therefore, the bit-rate for an STS-1 signal is (6480 bits/frame * 8000
frames/sec =) 51.84Mbps.
A simple illustration of this SONET STS-1 frame is presented below in Figure 31.
Figure 31 indicates that the very first byte of a given STS-1 frame (to be transmitted or received) is located in
the extreme upper left hand corner of the 90 column by 9 row array, and that the very last byte of a given STS-
1 frame is located in the extreme lower right-hand corner of the frame structure. Whenever a Network Element
transmits a SONET STS-1 frame, it starts by transmitting all of the data, residing within the top row of the STS-
1 frame structure (beginning with the left-most byte, and then transmitting the very next byte, to the right). After
the Network Equipment has completed its transmission of the top or first row, it will then proceed to transmit the
second row of data (again starting with the left-most byte, first). Once the Network Equipment has transmitted
the last byte of a given STS-1 frame, it will proceed to start transmitting the very next STS-1 frame.
The illustration of the STS-1 frame (in Figure 31) is very simplistic, for multiple reasons. One major reason is
that the STS-1 frame consists of numerous types of bytes. For the sake of discussion within this data sheet,
the STS-1 frame will be described as consisting of the following types (or groups) of bytes.
The Transport Overheads (or TOH) Bytes
The Envelope Capacity Bytes
9.2.1.1.1
The Transport Overhead (TOH) Bytes
The Transport Overhead or TOH bytes occupy the very first three (3) byte columns within each STS-1 frame.
Figure 32 presents another simple illustration of an STS-1 frame structure. However, in this case, both the
TOH and the Envelope Capacity bytes are designated in this Figure.
FIGURE 31. A SIMPLE ILLUSTRATION OF THE SONET STS-1 FRAME
STS-1 Frame (810 Bytes)
90 Bytes
9 Rows
First Byte of the STS-1 Frame
Last Byte of the STS-1 Frame
相关PDF资料
PDF描述
VE-21X-MX-F2 CONVERTER MOD DC/DC 5.2V 75W
MS3100A22-27S CONN RCPT 9POS WALL MNT W/SCKT
MS3106R28-10SW CONN PLUG 7POS STRAIGHT W/SCKT
VE-21X-MX-F1 CONVERTER MOD DC/DC 5.2V 75W
VI-21X-MX-F4 CONVERTER MOD DC/DC 5.2V 75W
相关代理商/技术参数
参数描述
XRT75L00ES 功能描述:时钟合成器/抖动清除器 1CH T3/E3/STS1 LIU+JA 3.3V RoHS:否 制造商:Skyworks Solutions, Inc. 输出端数量: 输出电平: 最大输出频率: 输入电平: 最大输入频率:6.1 GHz 电源电压-最大:3.3 V 电源电压-最小:2.7 V 封装 / 箱体:TSSOP-28 封装:Reel
XRT75L00IV 功能描述:外围驱动器与原件 - PCI 3.3V 1 CH E3/DS3/STS W/JITTER ATTEN RoHS:否 制造商:PLX Technology 工作电源电压: 最大工作温度: 安装风格:SMD/SMT 封装 / 箱体:FCBGA-1156 封装:Tray
XRT75L00IV-F 功能描述:外围驱动器与原件 - PCI Sngl Chip LIU DS3/E3 RoHS:否 制造商:PLX Technology 工作电源电压: 最大工作温度: 安装风格:SMD/SMT 封装 / 箱体:FCBGA-1156 封装:Tray
XRT75L00IVTR 功能描述:时钟合成器/抖动清除器 3.3V 1 CH E3/DS3/STS W/JITTER ATTEN RoHS:否 制造商:Skyworks Solutions, Inc. 输出端数量: 输出电平: 最大输出频率: 输入电平: 最大输入频率:6.1 GHz 电源电压-最大:3.3 V 电源电压-最小:2.7 V 封装 / 箱体:TSSOP-28 封装:Reel
XRT75L00IVTR-F 功能描述:时钟合成器/抖动清除器 3.3V 1 CH E3/DS3/STS W/JITTER ATTEN RoHS:否 制造商:Skyworks Solutions, Inc. 输出端数量: 输出电平: 最大输出频率: 输入电平: 最大输入频率:6.1 GHz 电源电压-最大:3.3 V 电源电压-最小:2.7 V 封装 / 箱体:TSSOP-28 封装:Reel