参数资料
| 型号： | XRT75L02IV-F |
| 厂商： | Exar Corporation |
| 文件页数： | 20/50页 |
| 文件大小： | 0K |
| 描述： | IC LIU E3/DS3/STS-1 2CH 100TQFP |
| 标准包装： | 90 |
| 类型： | 线路接口装置（LIU） |
| 驱动器/接收器数： | 2/2 |
| 规程： | DS3，E3，STS-1 |
| 电源电压： | 3.135 V ~ 3.465 V |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 100-LQFP |
| 供应商设备封装： | 100-TQFP（14x14） |
| 包装： | 托盘 |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页当前第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页第44页第45页第46页第47页第48页第49页第50页
XRT75L02
xr
TWO CHANNEL E3/DS3/STS-1 LINE INTERFACE UNIT WITH JITTER
REV. 1.0.3
25
that is compliant with the Alternating polarity requirement of the AMI (Alternate Mark Inversion) line code and
‘V’ refers to a Bipolar Violation (e.g., a bipolar pulse that violates the AMI line code). The substitution of B0V or
00V is made so that an odd number of bipolar pulses exist between any two consecutive violation (V) pulses.
This avoids the introduction of a DC component into the line signal.
4.2.2
HDB3 Encoding:
An example of the HDB3 encoding is shown in Figure 15. If the HDB3 encoder detects an occurrence of four
consecutive zeros in the data stream, then the four zeros are substituted with either 000V or B00V pattern. The
substitution code is made in such a way that an odd number of bipolar (B) pulses exist between any
consecutive V pulses. This avoids the introduction of DC component into the analog signal.
NOTES:
1.
When Dual-Rail data format is selected, the B3ZS/HDB3 Encoder is automatically disabled.
2.
In Dual-Rail format, the Bipolar Violations in the incoming data stream is converted to valid data pulses.
3.
Encoder and Decoder is enabled only in Single-Rail mode.
4.3
TRANSMIT PULSE SHAPER:
The Transmit Pulse Shaper converts the B3ZS encoded digital pulses into a single analog Alternate Mark
Inversion (AMI) pulse that meet the industry standard mask template requirements for STS-1 and DS3. See
Figures 8 and 9.
For E3 mode, the pulse shaper converts the HDB3 encoded pulses into a single full amplitude square shaped
pulse with very little slope. This is illustrated in Figure 7.
The Pulse Shaper Block also includes a Transmit Build Out Circuit, which can either be disabled or enabled by
setting the TxLEV_n input pin “High” or “Low” (in Hardware Mode) or setting the TxLEV_n bit to “1” or “0” in the
control register (in Host Mode).
For DS3/STS-1 rates, the Transmit Build Out Circuit is used to shape the transmit waveform that ensures that
transmit pulse template requirements are met at the Cross-Connect system. The distance between the
transmitter output and the Cross-Connect system can be between 0 to 450 feet.
FIGURE 14. B3ZS ENCODING FORMAT
FIGURE 15. HDB3 ENCODING FORMAT
0
1
V
B
V
1
0
V
B
V
0
T C lk
Line
S ignal
T PD A T A
0
1
V
B
V
1
0
V
0
TClk
Line
Signal
TPDATA
相关PDF资料 |
PDF描述 |
|---|---|
| MS3101F22-12S | CONN RCPT 5POS FREE HNG W/SCKT |
| M83723/75A14126 | CONN PLUG 12POS STRAIGHT W/SCKT |
| MS3106A20-15SW | CONN PLUG 7POS STRAIGHT W/SCKT |
| XRT83L38IB | IC LIU T1/E1/J1 OCTAL 225BGA |
| IDT72V3660L10PF8 | IC FIFO SS 4096X36 10NS 128-TQFP |
相关代理商/技术参数 |
参数描述 |
|---|---|
| XRT75L02IVTR-F | 功能描述:时钟合成器/抖动清除器 RoHS:否 制造商:Skyworks Solutions, Inc. 输出端数量: 输出电平: 最大输出频率: 输入电平: 最大输入频率:6.1 GHz 电源电压-最大:3.3 V 电源电压-最小:2.7 V 封装 / 箱体:TSSOP-28 封装:Reel |
| XRT75L03 | 制造商:EXAR 制造商全称:EXAR 功能描述:THREE CHANNEL E3/DS3/STS-1 LINE INTERFACE UNIT WITH JITTER ATTENUATOR |
| XRT75L03D | 制造商:EXAR 制造商全称:EXAR 功能描述:THREE CHANNEL E3/DS3/STS-1 LINE INTERFACE UNIT WITH SONET DESYNCHRONIZER |
| XRT75L03DES | 功能描述:时钟合成器/抖动清除器 3 CH T3/E3/STS1 LIU+DESYNCH3.3V RoHS:否 制造商:Skyworks Solutions, Inc. 输出端数量: 输出电平: 最大输出频率: 输入电平: 最大输入频率:6.1 GHz 电源电压-最大:3.3 V 电源电压-最小:2.7 V 封装 / 箱体:TSSOP-28 封装:Reel |
| XRT75L03DIV | 功能描述:外围驱动器与原件 - PCI 3CHNNEL E3/DS3/STS 1 SONET DE-SYNCH RoHS:否 制造商:PLX Technology 工作电源电压: 最大工作温度: 安装风格:SMD/SMT 封装 / 箱体:FCBGA-1156 封装:Tray |
发布紧急采购，3分钟左右您将得到回复。