参数资料
| 型号： | XRT75L02IV-F |
| 厂商： | Exar Corporation |
| 文件页数： | 40/50页 |
| 文件大小： | 0K |
| 描述： | IC LIU E3/DS3/STS-1 2CH 100TQFP |
| 标准包装： | 90 |
| 类型： | 线路接口装置（LIU） |
| 驱动器/接收器数： | 2/2 |
| 规程： | DS3，E3，STS-1 |
| 电源电压： | 3.135 V ~ 3.465 V |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 100-LQFP |
| 供应商设备封装： | 100-TQFP（14x14） |
| 包装： | 托盘 |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页当前第40页第41页第42页第43页第44页第45页第46页第47页第48页第49页第50页
XRT75L02
xr
TWO CHANNEL E3/DS3/STS-1 LINE INTERFACE UNIT WITH JITTER
REV. 1.0.3
43
8.2.2
DIGITAL LOOPBACK:
The Digital Loopback function is available either in Hardware mode or Host mode. When the Digital Loopback
is selected, the transmit clock (TxClk_n) and transmit data inputs (TPOS_n & TNEG_n) are looped back and
output onto the RxClk_n, RPOS_n and RNEG_n pins as shown in Figure 27. The data presented on TxClk,
TPOS and TNEG are not output on the TTIP and TRING pins.This provides the capability to configure the
protection card (in redundancy applications) in Digital Loopback mode without affecting the traffic on the
primary card.
NOTE: Signals on the RTIP_n and RRING_n pins are ignored during digital loop back.
8.2.3
IREMOTE LOOPBACK:
With Remote loop back activated as shown in Figure 28, the receive data on RTIP and RRING is looped back
after the jitter attenuator (if selected in receive or transmit path) to the transmit path using RxClk as transmit
timing. The receive data is also output via the RPOS and RNEG pins.
During the remote loop back mode, if the jitter attenuator is selected in the transmit path, the receive data after
the Clock and Data Recovery Block is looped back to the transmit path and passed through the jitter attenuator
using RxClk as the transmit timing.
NOTE: Input signals on TxClk, TPOS and TNEG are ignored during Remote loop back.
FIGURE 26. ANALOG LOOPBACK
FIGURE 27. DIGITAL LOOPBACK
TRING
TTIP
RRING
RTIP
RPOS
RNEG
RCLK
TNDATA
TCLK
TPDATA
HDB3/B3ZS
ENCODER
HDB3/B3ZS
DECODER
J
IT
T
E
R
2
A
T
E
N
U
A
T
O
R
J
IT
T
E
R
2
A
T
E
N
U
A
T
O
R
TIMING
CONTROL
DATA &
CLOCK
RECOVERY
1 if enabled
2 if enabled and selected in either Receive or Transmit path
Tx
Rx
1
TRING
TTIP
RRING
RTIP
RPOS
RNEG
RCLK
TNDATA
TCLK
TPDATA
HDB3/B3ZS
ENCODER
HDB3/B3ZS
DECODER
J
IT
TE
R
2
A
TT
E
N
U
A
TO
R
J
ITT
E
R
2
A
T
TE
N
U
A
T
O
R
TIMING
CONTROL
DATA &
CLOCK
RECOVERY
1 if enabled
2 if enabled and selected in either Receive or Transmit path
Tx
Rx
1
相关PDF资料 |
PDF描述 |
|---|---|
| MS3101F22-12S | CONN RCPT 5POS FREE HNG W/SCKT |
| M83723/75A14126 | CONN PLUG 12POS STRAIGHT W/SCKT |
| MS3106A20-15SW | CONN PLUG 7POS STRAIGHT W/SCKT |
| XRT83L38IB | IC LIU T1/E1/J1 OCTAL 225BGA |
| IDT72V3660L10PF8 | IC FIFO SS 4096X36 10NS 128-TQFP |
相关代理商/技术参数 |
参数描述 |
|---|---|
| XRT75L02IVTR-F | 功能描述:时钟合成器/抖动清除器 RoHS:否 制造商:Skyworks Solutions, Inc. 输出端数量: 输出电平: 最大输出频率: 输入电平: 最大输入频率:6.1 GHz 电源电压-最大:3.3 V 电源电压-最小:2.7 V 封装 / 箱体:TSSOP-28 封装:Reel |
| XRT75L03 | 制造商:EXAR 制造商全称:EXAR 功能描述:THREE CHANNEL E3/DS3/STS-1 LINE INTERFACE UNIT WITH JITTER ATTENUATOR |
| XRT75L03D | 制造商:EXAR 制造商全称:EXAR 功能描述:THREE CHANNEL E3/DS3/STS-1 LINE INTERFACE UNIT WITH SONET DESYNCHRONIZER |
| XRT75L03DES | 功能描述:时钟合成器/抖动清除器 3 CH T3/E3/STS1 LIU+DESYNCH3.3V RoHS:否 制造商:Skyworks Solutions, Inc. 输出端数量: 输出电平: 最大输出频率: 输入电平: 最大输入频率:6.1 GHz 电源电压-最大:3.3 V 电源电压-最小:2.7 V 封装 / 箱体:TSSOP-28 封装:Reel |
| XRT75L03DIV | 功能描述:外围驱动器与原件 - PCI 3CHNNEL E3/DS3/STS 1 SONET DE-SYNCH RoHS:否 制造商:PLX Technology 工作电源电压: 最大工作温度: 安装风格:SMD/SMT 封装 / 箱体:FCBGA-1156 封装:Tray |
发布紧急采购，3分钟左右您将得到回复。