参数资料
| 型号： | XRT75R03IVTR |
| 厂商： | Exar Corporation |
| 文件页数： | 86/92页 |
| 文件大小： | 0K |
| 描述： | IC LIU E3/DS3/STS-1 3CH 128LQFP |
| 标准包装： | 750 |
| 类型： | 线路接口装置（LIU） |
| 驱动器/接收器数： | 3/3 |
| 规程： | DS3，E3，STS-1 |
| 电源电压： | 3.135 V ~ 3.465 V |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 128-LQFP |
| 供应商设备封装： | 128-LQFP（14x20） |
| 包装： | 带卷 (TR) |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页第44页第45页第46页第47页第48页第49页第50页第51页第52页第53页第54页第55页第56页第57页第58页第59页第60页第61页第62页第63页第64页第65页第66页第67页第68页第69页第70页第71页第72页第73页第74页第75页第76页第77页第78页第79页第80页第81页第82页第83页第84页第85页当前第86页第87页第88页第89页第90页第91页第92页
xr
XRT75R03
THREE CHANNEL E3/DS3/STS-1 LINE INTERFACE UNIT WITH JITTER ATTENUATOR
REV. 1.0.8
84
9.0
DIAGNOSTIC FEATURES:
9.1
PRBS Generator and Detector:
The XRT75R03 contains an on-chip Pseudo Random Binary Sequence (PRBS) generator and detector for
diagnostic purpose. This feature is only available in Host mode. With the PRBSEN_n bit = “1”, the transmitter
will send out PRBS of 223-1 in E3 rate or 215-1 in STS-1/DS3 rate. At the same time, the receiver PRBS
detector is also enabled. When the correct PRBS pattern is detected by the receiver, the RNEG/LCV pin will go
“Low” to indicate PRBS synchronization has been achieved. When the PRBS detector is not in sync the
PRBSLS bit will be set to “1” and RNEG/LCV pin will go “High”.
With the PRBS mode enabled, the user can also insert a single bit error by toggling “INSPRBS” bit. This is
done by writing a “1” to INSPRBS bit. The receiver at RNEG/LCV pin will pulse “High” for one RxClk cycle for
every bit error detected. Any subsequent single bit error insertion must be done by first writing a “0” to
INSPRBS bit and followed by a “1”.
Figure 25 shows the status of RNEG/LCV pin when the XRT75R03 is configured in PRBS mode.
NOTE: In PRBS mode, the device is forced to operate in Single-Rail Mode.
9.2
LOOPBACKS:
The XRT75R03 offers three loopback modes for diagnostic purposes. In Hardware mode, the loopback modes
are selected via the RLB_n and LLB_n pins. In Host mode, the RLB_n and LLB_n bits n the Channel control
registers select the loopback modes.
9.2.1
ANALOG LOOPBACK:
1
JA in Tx Path Ch_n
R/W
0
Jitter Attenuator in Transmit/Receive Path Select Bit:
This input pin is used to configure the Jitter Attenuator
(within Channel_n) to operate in either the Transmit or
Receive path, as described below.
0 - Configures the Jitter Attenuator (within Channel_n) to
operate in the Receive Path.
1 - Configures the Jitter Attenuator (within Channel_n) to
operate in the Transmit Path.
0
JA0 Ch_n
R/W
0
Jitter Attenuator Configuration Select Input - Bit 0:
Please see the description for Bit 2 (JA1 Ch_n).
FIGURE 26. PRBS MODE
BIT NUMBER
NAME
TYPE
DEFAULT
VALUE
DESCRIPTION
RClk
RNEG/LCV
SYNC LOSS
PRBS SYNC
Single Bit Error
相关PDF资料 |
PDF描述 |
|---|---|
| MS27472T10B35SB | CONN RCPT 13POS WALL MNT W/SCKT |
| VE-21W-MX-F3 | CONVERTER MOD DC/DC 5.5V 75W |
| XRT75L00DIV | IC LIU E3/DS3/STS-1 SGL 52TQFP |
| MS27466T11B98SA | CONN RCPT 6POS WALL MT W/SCKT |
| MS27466E15A15S | CONN RCPT 15POS WALL MT W/SCKT |
相关代理商/技术参数 |
参数描述 |
|---|---|
| XRT75R03IVTR-F | 功能描述:时钟合成器/抖动清除器 RoHS:否 制造商:Skyworks Solutions, Inc. 输出端数量: 输出电平: 最大输出频率: 输入电平: 最大输入频率:6.1 GHz 电源电压-最大:3.3 V 电源电压-最小:2.7 V 封装 / 箱体:TSSOP-28 封装:Reel |
| XRT75R06 | 制造商:EXAR 制造商全称:EXAR 功能描述:SIX CHANNEL E3/DS3/STS-1 LINE INTERFACE UNIT WITH JITTER ATTENUATOR |
| XRT75R06D | 制造商:EXAR 制造商全称:EXAR 功能描述:SIX CHANNEL E3/DS3/STS-1 LINE INTERFACE UNIT WITH SONET DESYNCHRONIZER |
| XRT75R06DES | 功能描述:时钟合成器/抖动清除器 RoHS:否 制造商:Skyworks Solutions, Inc. 输出端数量: 输出电平: 最大输出频率: 输入电平: 最大输入频率:6.1 GHz 电源电压-最大:3.3 V 电源电压-最小:2.7 V 封装 / 箱体:TSSOP-28 封装:Reel |
| XRT75R06DIB | 功能描述:网络控制器与处理器 IC 6CH E3/DS3/STS1 LIU w/DeSynch RoHS:否 制造商:Micrel 产品:Controller Area Network (CAN) 收发器数量: 数据速率: 电源电流（最大值）:595 mA 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:PBGA-400 封装:Tray |
发布紧急采购，3分钟左右您将得到回复。