参数资料
型号: XRT83L314IB-L
厂商: Exar Corporation
文件页数: 30/84页
文件大小: 0K
描述: IC LIU T1/E1/J1 14CH 304TBGA
标准包装: 27
类型: 线路接口装置(LIU)
驱动器/接收器数: 14/14
规程: T1,E1,J1
电源电压: 3.135 V ~ 3.465 V
安装类型: 表面贴装
封装/外壳: 304-LBGA
供应商设备封装: 304-TBGA(31x31)
包装: 托盘
XRT83L314
14-CHANNEL T1/E1/J1 LONG-HAUL/SHORT-HAUL LINE INTERFACE UNIT
REV. 1.0.0
32
3.6.2
T1 Short Haul Line Build Out (LBO)
The short haul transmitter output pulses are generated using a 7-Bit internal DAC (6-Bit plus the MSB sign bit).
The line build out can be set to interface to five different ranges of cable attenuation by programming the
appropriate channel register. The pulse shape is divided into eight discrete time segments which are set to
fixed values to comply with the pulse template. To program the eight segments individually to optimize a
special line build out, see the arbitrary pulse section of this datasheet. The short haul LBO settings are shown
3.6.3
Arbitrary Pulse Generator For T1 and E1
The arbitrary pulse generator divides the pulse into eight individual segments. Each segment is set by a 7-Bit
binary word by programming the appropriate channel register. This allows the system designer to set the
overshoot, amplitude, and undershoot for a unique line build out. The MSB (bit 7) is a sign-bit. If the sign-bit is
set to "0", the segment will move in a positive direction relative to a flat line (zero) condition. If this sign-bit is
set to "1", the segment will move in a negative direction relative to a flat line condition. The resolution of the
DAC is typically 60mV per LSB. Thus, writing 7-bit = 1111111 will clamp the output at either voltage rail
corresponding to a maximum amplitude. A pulse with numbered segments is shown in Figure 29.
FIGURE 29. ARBITRARY PULSE SEGMENT ASSIGNMENT
NOTE: By default, the arbitrary segments are programmed to 0x00h. The transmitter outputs will result in an all zero
pattern to the line interface.
3.7
DMO (Digital Monitor Output)
The driver monitor circuit is used to detect transmit driver failures by monitoring the activities at TTIP/TRING
outputs. Driver failure may be caused by a short circuit in the primary transformer or system problems at the
transmit inputs. If the transmitter of a channel has no output for more than 128 clock cycles, DMO goes "High"
until a valid transmit pulse is detected. If the DMO interrupt is enabled, the change in status of DMO will cause
TABLE 12: SHORT HAUL LINE BUILD OUT
LBO SETTING EQC[4:0]
RANGE OF CABLE ATTENUATION
08h (01000)
0 - 133 Feet
09h (01001)
133 - 266 Feet
0Ah (01010)
266 - 399 Feet
0Bh (01011)
399 - 533 Feet
0Ch (01100)
533 - 655 Feet
1
2
3
4
5
6
7
8
Segment
Register
1
0xn8
2
0xn9
3
0xna
4
0xnb
5
0xnc
6
0xnd
7
0xne
8
0xnf
相关PDF资料
PDF描述
XRT83L34IV-F IC LIU T1/E1/J1 QUAD 128TQFP
XRT83L38IB-F IC LIU T1/E1/J1 OCTAL 225BGA
XRT83SH314IB-F IC LIU T1/E1/J1 14CH 304TBGA
XRT83SH38IB-F IC LIU SH T1/E1/J1 8CH 225BGA
XRT86L30IV-F IC LIU/FRAMER TI/E1/J1 SGL 128LQ
相关代理商/技术参数
参数描述
XRT83L34 制造商:EXAR 制造商全称:EXAR 功能描述:QUAD T1/E1/J1 LH/SH TRANSCEIVER WITH CLOCK RECOVERY AND JITTER ATTENUATOR
XRT83L34_05 制造商:EXAR 制造商全称:EXAR 功能描述:QUAD T1/E1/J1 LH/SH TRANSCEIVER WITH CLOCK RECOVERY AND JITTER ATTENUATOR
XRT83L34ES 功能描述:外围驱动器与原件 - PCI RoHS:否 制造商:PLX Technology 工作电源电压: 最大工作温度: 安装风格:SMD/SMT 封装 / 箱体:FCBGA-1156 封装:Tray
XRT83L34IV 功能描述:网络控制器与处理器 IC RoHS:否 制造商:Micrel 产品:Controller Area Network (CAN) 收发器数量: 数据速率: 电源电流(最大值):595 mA 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:PBGA-400 封装:Tray
XRT83L34IV-F 功能描述:网络控制器与处理器 IC RoHS:否 制造商:Micrel 产品:Controller Area Network (CAN) 收发器数量: 数据速率: 电源电流(最大值):595 mA 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:PBGA-400 封装:Tray