- 您现在的位置：买卖IC网 > Datasheet目录537 > XT09-MI (Digi International/Maxstream)MODULE RF 900MHZ 1W 115K W/MMCX Datasheet资料下载
参数资料
| 型号： | XT09-MI |
| 厂商： | Digi International/Maxstream |
| 文件页数： | 39/71页 |
| 文件大小： | 0K |
| 描述： | MODULE RF 900MHZ 1W 115K W/MMCX |
| 标准包装： | 1 |
| 系列： | XTend™ |
| 频率： | 900MHz |
| 数据传输率 - 最大： | 125kbps |
| 调制或协议： | FHSS，FSK |
| 功率 - 输出： | 1W |
| 灵敏度： | -100dBm |
| 电源电压： | 2.8 V ~ 5.5 V |
| 电流 - 接收： | 80mA |
| 数据接口： | PCB，通孔 |
| 天线连接器： | MMCX |
| 工作温度： | -40°C ~ 85°C |
| 封装/外壳： | 模块 |
| 包装： | 散装 |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页当前第39页第40页第41页第42页第43页第44页第45页第46页第47页第48页第49页第50页第51页第52页第53页第54页第55页第56页第57页第58页第59页第60页第61页第62页第63页第64页第65页第66页第67页第68页第69页第70页第71页
9XTend? ? OEM ? RF ? Module ?‐? Product ? Manual ? v2.x4x ? [2007.01.04]
WA (Active Warning Numbers) Command
<Diagnostics> The WA command reports the
warning numbers of all active warnings - one
warning number per line. No further information
is shown and warning counts are not reset.
Chapter ? 3 ?‐? RF ? Module ? Configuration
AT Command: ATWA
Parameter Range: Returns string - one
warning number per line.
Sample Output (indicates warnings 1 and 3 are currently active):
1
3
OK
WN (Warning Data) Command
<Diagnostics> WN command is used to report the
following data for all active and sticky warnings:
? Warning number & description
AT Command: ATWN
Parameter Range: returns string
? Number of occurrences since the last WN or WS command
? Whether the warning is currently active
Warnings, which are not currently active and have not been active since the last issuance of the
WN or WS commands, are not displayed. The WN command also resets all non-zero warning
counts; except for warnings that are presently active, which are set to 1.
Sample output:
Warning 4: Over-temperature
5 occurrences; presently inactive.
Warning #
1
2
3
4
5
6
7
8
Description
Under-voltage. This is caused if the supply voltage falls below the minimum threshold for the lowest power level (2.8 V). If/when the voltage
rises above the threshold, the warning is deactivated. The module will not transmit below this voltage threshold.
Over-voltage. This is caused if the supply voltage exceeds 5.75 V. Transmission is not allowed while this warning is active.
Under-temperature. This is caused if the temperature sensed by the module is less than -40 C. The module does not artificially limit operation
while this warning is active, but module functionality is not guaranteed.
Over-temperature. This is caused if the temperature sensed by the module is greater than 105 C. The module does not allow transmission nor
reception while this warning is active. The warning is deactivated when the temperature falls to 100 C.
Power reduced. This is caused if the transmit power has to be reduced from the level programmed by PL Command due to insufficient supply
voltage. The 1 W power level requires 4.75 V or higher; 500 mW requires 3.0 V or higher; 100 mW, 10 mW and 1 mW require 2.8 V or higher.
Default calibration data in flash. This is caused if the module-specific power calibration data is either not present or is invalid, or if none of the
parameters have been modified from their default values. Power levels may be incorrect.
Default configuration parameters in flash. This is caused if user-modifiable parameters (i.e. those stored by a 'WR' command) in flash are all the
compiled-in default values. This is caused if the user configuration is found to be not present or invalid at power-up and there is no custom
configuration, or if no user-modifiable parameters have been modified from the compiled-in defaults. Modification of one or more parameters
without the subsequent WR to commit the changes to flash will not deactivate this warning, since it reflects the status of the parameters in flash.
Note that this warning does not reflect usage of the custom configuration defaults, only usage of the compiled-in defaults.
Default factory configuration parameters in flash. This is caused if the factory parameters in flash are all the default values. This is caused if the
factory configuration is found to be not present or invalid at power-up, or if no factory parameters have been modified.
WR (Write) Command
<(Special)> The WR command is used to write
configurable parameters to non-volatile memory
(Values remain in the module's memory until
AT Command: ATWR
Binary Command: 0x08
overwritten by another use of WR Command).
If changes are made without writing them to non-volatile memory, the module will revert back to
previously saved parameters the next time the module is powered-on.
If the non-volatile user configuration is not correct, WR will re-attempt (up to 3x). If all three
attempts fail, the command will return an ERROR alert.
WS (Sticky Warning Numbers) Command
<Diagnostics> The WS command reports warning
numbers of all warnings active since the last use
of the WS or WN command (including any warn-
ings which are currently active). This command
AT Command: ATWS
Parameter Range (read-only): 1 - 8
Number of bytes returned: 1
also resets all non-zero warning counts, except
for warnings that are presently active, which are set to 1.
? ? 2007 ? MaxStream, ? Inc.
????? 39
相关PDF资料 |
PDF描述 |
|---|---|
| XT09-PKI-EA-NA | MODEM RF 900MHZ 1W ETHER INT |
| XT09-SI | MODULE RF 900MHZ 1W 115K W/RPSMA |
| XU-A11 | X-STICK 2.4GHZ USB TO XBEE |
| XV-8000CB :3 50.3000KHZ+/-60DPS | AUTOMOTIVE GYRO SENSOR +/-60DPS |
| YB03WKW01-6B-JB | INDICATOR PB RECT WHT LED ILLUM |
相关代理商/技术参数 |
参数描述 |
|---|---|
| XT09-MI-MESH | 功能描述:射频模块 9XTend, 1W Trnsvr MMCX,115000bps,Mesh RoHS:否 制造商:Linx Technologies 产品:Transceiver Modules 频带:902 MHz to 928 MHz 输出功率:- 15.5 dBm to + 12.5 dBm 接口类型:UART 工作电源电压:- 0.3 VDC to + 5.5 VDC 传输供电电流:38.1 mA 接收供电电流:22.7 mA 天线连接器类型:U.FL 最大工作温度:+ 85 C 尺寸:1.15 mm x 0.63 mm x 0.131 mm |
| XT09MINA | 制造商:DIGI 功能描述:New |
| XT09-MI-NA | 功能描述:射频模块 9XTend 1W transceiv encryption 9600 bps RoHS:否 制造商:Linx Technologies 产品:Transceiver Modules 频带:902 MHz to 928 MHz 输出功率:- 15.5 dBm to + 12.5 dBm 接口类型:UART 工作电源电压:- 0.3 VDC to + 5.5 VDC 传输供电电流:38.1 mA 接收供电电流:22.7 mA 天线连接器类型:U.FL 最大工作温度:+ 85 C 尺寸:1.15 mm x 0.63 mm x 0.131 mm |
| XT09-MT | 功能描述:射频模块 9XTend 1W transceiv onnector 115000 bps RoHS:否 制造商:Linx Technologies 产品:Transceiver Modules 频带:902 MHz to 928 MHz 输出功率:- 15.5 dBm to + 12.5 dBm 接口类型:UART 工作电源电压:- 0.3 VDC to + 5.5 VDC 传输供电电流:38.1 mA 接收供电电流:22.7 mA 天线连接器类型:U.FL 最大工作温度:+ 85 C 尺寸:1.15 mm x 0.63 mm x 0.131 mm |
| XT09-PKC-U | 功能描述:射频模块 9XTend 1W USB w/o accessories RoHS:否 制造商:Linx Technologies 产品:Transceiver Modules 频带:902 MHz to 928 MHz 输出功率:- 15.5 dBm to + 12.5 dBm 接口类型:UART 工作电源电压:- 0.3 VDC to + 5.5 VDC 传输供电电流:38.1 mA 接收供电电流:22.7 mA 天线连接器类型:U.FL 最大工作温度:+ 85 C 尺寸:1.15 mm x 0.63 mm x 0.131 mm |
发布紧急采购，3分钟左右您将得到回复。